Having problems with your Eureka Smart 4870DT Bagged Upright Vacuum ?
Handle release broken
\015 Have a Eureka Boss/Smart Vac, model 4870GZ. Handle release is broken. Gray step pedal is fine, and flat springs are OK. Some clear plastic pieces are broken. Can I fix this, or do I need a repair shop? Or just something just snap back together with some brute force?\015
Repair Help & Product Troubleshooting for Eureka Smart 4870DT Bagged Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I broke the handle part of the shark steamer #53101. I don't have the book to try to tell you the parts I need. Can you send me a picture or a copy of the steamer. It is purple. The above number may not be the correct one. It is broken in the center part. It has a little small circular piece that joins the two pieces which are broken. The beginning of the handle at the bottom of the steamer and the next session which has the steam release. The top of the handle is okay . It the middle and bottom
Hi,Ann there are very few parts for these...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum
The handle release pedal wasn't allowing the handle to lower. I took off the pedal and saw the spring load part was broken. What is this part and how to replace it? Bissell 3760-3 handle release
Our vacuum recently had an issue with it's motor, we had to borrow a neighbors a couple times while we were trying to figure out what to do. We decided to take it to a place that specializes in cleaning supplies and cleaning tools to see if they had ... Vacuums
The wand release button has broken. Therefore, the wand does not lock into place which results in swivelling of the handle and sometimes the handle coming off while using the vacuum cleaner. Can this wand release be readily repaired?
... Euro-Pro NV31 Infinity Vacuum
Hoover floormate handle release pedal broken. Need diy repair information.
... Hoover Vacuums
Broken handle release spring assembly on an electrolux intensity
... Electrolux EL5020 Vacuum
Broken handle release
Most times they don't break, it is the 2 screw holes at the back that back and the top will raise up from the base. If this is the case, remove the 2 screws and install longer ones with a flat washer on them to fashen down the top. But first the to ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
Handle release broken
... Eureka Smart 4870DT Bagged Upright Vacuum
Broken Handle Release Pedal
What is part number for broken pedal release ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum
How to remove broken handle release on hoover windtunnel upright
... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum
The handle release button is broken/ the handle will not fold
If you go to this URL:\015\012\015\012http://www.ereplacementparts.com/eureka-2590a-carpet-cleaner-parts-c-108750_109432_109471.html\015\012\015\012you should be able to identify the part and order it as well.\015\012\015\012If you ... Eureka Atlantis 2590A Wet/Dry Vacuum
Handle release broken Handle will not stay up
... Hoover F7431-900 SteamVac Vacuum
Chassis hook broken to rod which controls release of liquid shampoo in Hoover steam cleaner. It is the back of the handle area that is snapped off, not the actual rod with "push on / release"
If it is part of the handle, it breaks inside alot, part number 39458006. #2 in the picture.\015\012 \015\012 ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum
Hoover WindTunnel Self Propelled Handle Release Lever broken
... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum
Water Leakage We have a Bissell Proheat (Pro Tech). I don't think it is the 2X model. When releasing the water with the knob on the handle, water comes out the side of the housing at the lower part of the unit. Is their a seal that my be worn out or broken. Can you give us some ideas before we take it to an expensive repair man to fix
Check the water bottle. Ours has been doing the same but putting a bit of j cloth between what they call the o ring and the cap fixed it. Really you need a new bottle assembly ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum
PLASTIC HANDLE RELEASE BROKEN. WHERE DO I FIND A REPLACEMENT?
Greetings from GoVacuum.com,\015\012\015\012\015\012We are a vacuum cleaner parts store, http://www.govacuum.com, and we carry parts for over 40 different brands ... Vacuums
How can you fix a hoover spinscbrub 50 handle release that is broken?
... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum
Handle release pedal broken, how do i repair?
... Bissell 6591 Power Trak Revolution Bagless Upright Vacuum
Handle Release Pedal is broken on my Bissell Cleanview 82h1 - can order a new on and replace it?
... Bissell 82H1 Cleanview Helix Bagless Upright Vacuum
Foot controlled handle release lever is broken. Where to get parts?
I had same problem - the foot release pedal would not spring into place when unit was upright (but would work if you nudged in place with your foot). I installed a replacement part, and it didn't fix the problem. I cut out a small sqare of sponge ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum
Hoover savvy handle release pedal does not retract. There does not seem to be any mechanism to force it back, is something broken or missing, like a spring?
Yes the handle release pedal is broken. i have the same problem and ordering the spare as i'm writing this email ... Vacuums
How to replace handle release pedal on dirt devil kinetix self propelled vacuum cleaner. I need to remove the broken pedal and replace it with the new one.
... Dirt Devil Reaction Twin Cyclone Upright Vacuum
Possible broken belt - where do I find access to the belt. The beater bar does not rotate when i release the handle. I like this machine, but It is only 2 years old, the warranty has expired. And i must say, I am disappointed I am concerned that this article will end up in the landfill, adding one more problem for the environment.
As you do not say which type of vac ? but assume definately upright hoover/dyson or similar ? the actual belt is not difficult to renew on either model/s at this stage can only suggest you turn vac over to reveal the cover that houses the ro ... Vacuums
I have a clearviewII model 3576-3 and the handle release lever is broken. How to I remove the old lever and install a new one? Thanks, Pat
... Bissell Vacuums
I have a Hoover Windtunnel Dual V. The vacuum and I did a tumble down stairs and the handle release pedal was broken. Is that something I can order a part for and have my husband put on? If so, where would I obtain the part? Thanks. Roxanna Kindler [email protected]
Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=627747\015\012Generic problem for all Vacuums\015\012I have a Hoover Windtunnel\015\012Posted by ekindl ... Vacuums
Foot latch is broken. need to replace with new one. how does one access to remove the foot pedal latch. By foot latch, I mean the foot lever that releases the upright to lower the handle and begin vacuuming.
It is accessed from the bottom underneath by the rear wheel. However, If there are and cracks on the pedal release socket area then the base will need replacement. parts are little cost but the unit needs to be completely disassembled. ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum