Having problems with your Eureka Smartvac 4870 Bagged Upright Vacuum ?

Eureka Boss belt keeps breaking

\015 I keep replacing the belt and it last about 2 weeks and breaks\015

Answers :

Repair Help & Product Troubleshooting for Eureka Smartvac 4870 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My Eureka Boss 4870 belt keeps fraying, stretching, and breaking. When I replace the belt and turn the roller brush by hand, within just a few turns the belt drifts off center and to the left of the roller brush where it starts to rub. How do I fix this?


... Eureka Smartvac 4870 Bagged Upright Vacuum

Eureka Boss belt keeps breaking


... Eureka Smartvac 4870 Bagged Upright Vacuum

My Eureka Boss vacuum belt keeps breaking


I have been searching the machine for something which could be rubbing against the belt to cause it to fray and break as often as it does. So far, I haven't found anything. I have heard that the belts, called ribbon belts, are terrible! I find tha ... Eureka Smartvac 4870 Bagged Upright Vacuum

My belt to my EUREKA KEEPS BREAKING


... Vacuums

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

I have a eureka power paw that keeps breaking belts. there doesnt seem to be a part that keeps the belt in place


My belt keeps breaking too, but worse is that I can't find out the size for replacing. Who knows the size I need for the Eureka Power Paw? ... Eureka Vacuums

EUREKA PETPAL VACUUM: I bought the original EurekA BELTS size U from Durabelt and a belt last only 2-3 times vacuuming...it keeps breaking...why? Please help. Thank you !


... Eureka 2941AVZ Vacuum

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

Boss smartvac The piece that keeps the roller from moving when set on hose doesn't work right. I keep breaking belts. How do I fix this?


... Eureka 4870SZX BOSS SMARTVAC PET LOVER Bagged Upright Vacuum

Eureka c2094 round belt keeps breaking immediately


... Eureka C2094G Vacuum

Belts keep breaking


Check the brush roll ends to see if they have melted or frozen. They should turn freely, part #361869-1. Make sure the belt isn't being pinched somewhere. ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

We have had three belts break on your hoover vaccum cleaner u5472-940. It is easy to replace, you just remove the plastic part over it, put belt on wheel and then put it back on. Any idea on why the belt keeps breaking?


Sometimes when you buy belts from the walmart or target, they are not at the correct specification and they brake as soon as you turn on the machine. i would suggest that you buy these belts from the company. ... Hoover F6021-900 Steam Vacuum

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum

Keep replacing belt that drives brusher but keeps breaking. When feel belt driver rod it is superheated.....could it be melting into the stretched belt causing it to weaken?


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=559226\015\012Generic problem for all Vacuums\015\012Keep replacing belt that drives\015\012 ... Vacuums

I keep replacing the belt and keeps melting and breaks. what do i need to do? everything else is working, the little piece of metal that hooks on the belt gets too hot and melt the belt


I think your talking about the motor spindel,,(the little metal bit?) if the motor is that hot its going to burn out soon, check that the brush is free to turn if its tight free it off its full of grit or fluff also check that the motor turns freely ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

Looking for Eureka belt 70646A for a Eureka The Boss upright


I just replaced the belt on my Eureka The Boss Smart Vac (Model 4870D). I purchased a namebrand Eureka R belt from a local vendor. I did my best to follow the instructions printed on the bottom of the machine. I turned on the vacuum cleaner and the ... Vacuums

How to replace belt on a eureka boss vacuum - Eureka 4870SZX BOSS SMARTVAC PET LOVER Bagged Upright Vacuum


If you look on the base plate you should see a diagram of how to do it,but if yours don't have a diagram then remove the screws from the base plate it should be three or four they have arrows next to them. take the base plate off and remove the brush ... Eureka 4870SZX BOSS SMARTVAC PET LOVER Bagged Upright Vacuum

Eureka Boss 12 amp Belt change - Eureka Mega Boss 4460DT Vacuum


... Eureka Mega Boss 4460DT Vacuum

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa


Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.


I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......


Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

Drive belt keeps breaking on hoover windtunnel vacuum. Drive belt won't turn the agitator. Belt is new. Small belt is new. Agitator is new.


... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Belts keep burning and breaking on turbopower 7100


If a roller brush does not rotate freely, the motor shaft spins in one place on the belt until it heats it up and breaks it. Roller brushes can become clogged on the ends, especially with pet hair. The solution is to remove the roller brush completel ... Vacuums

New Eureka vacuum cleaner belt keeps slipping off


You may have a bad brush roll, part #61250-1, or the base itself has a problem and isn't letting the brush roll sit straight so it can be in alignment. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0511 seconds