Having problems with your Eureka Smartvac 4870 Bagged Upright Vacuum ?

The handle release pedal broke on my Eureka Smartvac. The spring is still in tact. I have a replacement pedal, but cannot figure out how to install it. Any suggestions?


Answers :

Repair Help & Product Troubleshooting for Eureka Smartvac 4870 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The handle release pedal broke on my Eureka Smartvac. The spring is still in tact. I have a replacement pedal, but cannot figure out how to install it. Any suggestions?


... Eureka Smartvac 4870 Bagged Upright Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

Dear Sir or Madam, I own a black 23 x 47 x 7 mm Rowenta lighter. It has a screw on bottom that I cannot remove. What is it hiding ? Is this lighter refillable ? Is there a flint to replace ?. I've found on your site the following : "By jbbiii on Apr 06, 2009 Father died and left me a Rowenta lighter purchased in Stutgart in 1952. It has a screw on bottom with spring to replace the flint, but I cannot figure out how to open the bottom to replace the cotton wadding which I can see through the hole


Hello \015\012The flint should be near the striker.Or the thumb roller,usually below it.\015\012As old as it is you may not see it beacause its worn down.\015\012\015\012Maybe taking it to an antique store or a smoke shop woul ... Vacuums

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

Ordered a replacement motor for Hoover GUV garage utility vac L2310. It took months to receive. There are no installation instructions and the old motor was left with one of the dealers and lost. Any suggestions as to how to replace this motor.


... Hoover L2310 GUV Central System Vacuum

I have necchi ALICE model purchased in about 1972. Amazing machine but the floor pedal needs replacing and cannot find one. Code on plate of pedal is A 50305/4 made in italy.I live in montreal,canada. thanks, ania barnes


... Vacuums

My DC-25 will not return to the upright position. I emailed Dyson support and the response was: "The DC25 stabilizer wheels will not lock into position if the “spokes” on the red pedal are not seated correctly." I agree with that assessment, but cannot figure out how to get the spokes on the red pedal to seat correctly. The manual is useless for this problem since that part of the vacuum cleaner came already assembled, so the manual does not address it. Help.


It sounds like the undercarriage unit has failed. It is a common problem on ball models. The DC25 is a recent model so would still be under Dyson's 5 year guarantee. Get them out to it. ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have a Bissell Go Vac that does not want to take acharge from the charger. Where do I replace the battery at? It is a model 3302. Cannot figure out how to replace the battery. Help!


... Bissell Vacuums

Cannot figure out how to install brush belt on a bissell proheat


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

Hoover Handle Release Pedal Replacement--How is it possible?


If you look at the picture, the slots are right across from the drive wheels, you can see the slots in the picture. Use a flat blade screwdriver. ... Vacuums

My Sebo X1 stopped working and my husband tested it and determined that the on off switch was not working. I purchased a replacement switch online but I cannot figure out how to remove the old switch. Please can you help?


Thanks for your question!I'm sorry that you haven't received an answer yet.The response rate on FixYa FREE questions is usually over 80%, but sometimes questions go un-answered when:1. the question is unclear, incomplete, or poorly ... Sebo Automatic X1 Bagged Upright Vacuum

I cannot figure out how to replace the bulbs I do not have the original adapter. What voltage was it?


What kind of vacuum is it? A manual should be able to be downloaded from the manufactures web site showing the type and voltage for the bulb and location were parts are available. ... Vacuums

My Sebo X1 stopped working and my husband tested it and determined that the on off switch was not working. I purchased a replacement switch online but I cannot figure out how to remove the old switch. Please can you help?


Www.manualnguide.com/manual/sebo-x1-repair/page/3/\015\012\015\012Above is your user manual, and below is an exploded diagram so you can see where it all goes. Find all the screws lock ... Sebo Automatic X1 Bagged Upright Vacuum

I have a 5 yr old Ariens snowblower ( model # 924124). I am having a problem with the deflector cable freezing. I had the deflector cable replaced a yr or 2 ago. I took the cable off and brought it in the house to thaw. When I reinstalled the cable, it worked ine except the shute does not operate in its full range of motion. I have the cable EXACTLY in its original position and routing. The shute only closes about half way. I cannot get the shute to close any lower. Any suggestions?


... Vacuums

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.


Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums

Belt broke I need to find out how to get in the vacuum to replace the belt but cannot figure it out. I do not have the owners manual for this Eurka The Boss Superlit bagless (402a) please e-mail me any directions if you know how to do it,thanks. [email protected]


How do i change the belt on my eureka the boss lite vacum ... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum

I have a kenmore 116.25615506 vac and I want to replace the connector on the power sweeper. I cannot figure out how to disassemble the "electric folding wand" to get the connector out


... Kenmore Vacuums

I have a robot coupe R2 and i cannot figure out how to take it apart and replace the safety switch


... Vacuums

Vacuum filter I bought a vacuum from Walmart that works really well, but I cannot find a replacement filter for it. The lable on the bottom of the vacuum reads "Excellent Solutions LTD" Model C 2006B also has 31CX E306773 numbers on it. 120V-60Hz 10Amps I have searched the internet but no luck so far....any suggestions?


We bought one a couple years ago too, no filters. Now, WalMart carries replacement filters for other vacuums that will fit. Go back to WalMart and pick up the Durabrand CF2006 - it's in an orange box, works like a champ, I think it was around $5. ... Vacuums

Need to replace a vacuum belt on a eureka model 4377. I cannot figure out how to remove the bottom portion to get to it.


Here is a link to the manual and a link to the belt you need:Eureka 4377 Replacement Belt ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Houver Cleaner My self propelled windtunell baged Vacumn has a broken belt. The small visible one that is visible is intact. This is the thick belt. I cannot for the life of me figure out what to open and how to replace it. The model # is U6 401-9RM I keep asking for a manual online but it doesn't recognize this number. I am 67 yrs old broke and fix it challenged..lol can you help me?


Take off the bottom plate, The flat belt ges around the motor shaft and then around the bigger pulley by the V belt. It will stretch to o on.\015\012\015\012 ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

No suction I just replaced the bag, and normally after this I have a lot of suction. Now that I have changed the bag I have less suction that I had before. Not even enough to picj up dog hair. I snaked he hose and checked all of the connections. It seems to have an air leak but no amount of tape will fix this. I cleaned the filer as well with warm water and dried it and re installed but still absolutely no suction. I am ready to throw it out! Any suggestions would be appreciated


1, Does the blower (discharge) side blow bunches of air??Yes: Something is clogged from the bag to the hose end. Try blowing out the hose from the discharge side.Or: The bag is not properly seated. Make sure that the plastic piece is ... Kenmore 23313 Whispertone Bagged Canister Vacuum

Dead motor I purchased a new motor for my Dyson Animal but I cannot figure out how to get the thing apart to replace it. There are weird star shaped screws but I can't even see how removing those would get me where i need to be. HELP!!!


Ace Hardware or Home Depot should have your star screws ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0924 seconds