Having problems with your Eureka Smartvac 4870 Bagged Upright Vacuum ?

The brush does not stop rotating when the dial is set to "hose". What might be broken or need fixing?


Answers :

Hi. most vaccums the brushes dont stiop turning when you use the hose. so everything should be fine. keep on cleaning. have a good day!
Repair Help & Product Troubleshooting for Eureka Smartvac 4870 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brush does not stop rotating when the dial is set to "hose". What might be broken or need fixing?


Hi. most vaccums the brushes dont stiop turning when you use the hose. so everything should be fine. keep on cleaning. have a good day! ... Eureka Smartvac 4870 Bagged Upright Vacuum

DT 1300 As I am vacuuming the motor seems to fade in and out and sometimes stops running for a few seconds and then resumes. If I move the hose a bit near the vacuum end, it runs smoothly again. Does this sounds as if there might be a short in the motor? Would this be something I can fix myself or does the vacuum need to go in for repairs.


... Oreck DutchTech DTX1300C with Motorized Carpet Brush Bagged Canister Vacuum

My bissel 310-3150 will not dispense cleaning solution, hence it will not suction up water. Red spinny thing will spin a couple of revolutions, then quit. When that stops, everything stops. What can I do to fix this? Unemployed so repair shop is out. DIY fix is needed.


... Bissell 1693 PowerSteamer Upright Vacuum

Hoover floormate handle release pedal broken. Need diy repair information.


... Hoover Vacuums

The last time I sewed with my Necchi the tension was fine. Today when I threaded my needle, the thread felt tight in the upper tension dial. I tried re-threading the machine several times, but it didn't help. Now the parts of the tension dial are all loose and wobbbly and I have no upper tension. Doesn't matter what the dial is set on. The tension dial appears to be broken, but I don't know how that could have happend since I store it in a case.


I found this thread (no pun intended):\015\012\015\012http://www.fixya.com/support/t2902978-need_replace_upper_tension_dial\015\012 ... Vacuums

Brush Roller Wondering if I need a new brush as well as a belt. The Roller seems to have trouble spinning when it makes contact with the carpet no matter how the height is set. Everything else seems to work fine. Do I need a new roller to fix this problem?


The bearings can go bad in the brushroll. It may need replaced, even if the brushes aren't worn. Helpful link....\015\012\015\012 ... Kirby G6 Bagged Upright Vacuum

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula


There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

I have an Electrolux Oxygen 3 vacuum I purchased rebuilt. After 1 month the power stopped working. I took it into Electrolux Authorized repair dealer, which was a horrible experience. When we received it back it was clearly not as powerful as before. Does anyone have any suggestions on what the problem may be? I would rather fix it myself than take it back to them. The next repair center is too far away. I am pretty good with fixing things, just needs some guidance. I think the repair center rep


Never have liked Electrolux doing any repair because it has been my experience that they don't do what they say they did....if you can read between the lines.....give me a picture of the unit and more details and I'll try and help you. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode


... Hoover Vacuums

How do we fix a broken upright stop? the upright stop will not stay up. something is not right.


Hi Jeremy! You may want to have one of our techs at a BISSELL Authorized Service Center inspect your machine.\015\012Here's a quick link to assist you in locating one in your area: ... Bissell 7950 ProHeat Upright Wet/Dry Vacuum

I need a manual for this vacuum as well as an answer as to why the belt stops working. how to fix it please and thank you......Trisha


The model number is 5770 and the user's manual can be downloaded at: \015\012http://www.bissell.com/user-guides/?searchtex ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I have a Hoover SteamVac Carpet Cleaner with Clean Surge. I lent it to my mother who used it without the brush attached underneath. Now it doesn?t **** up water and the brushes don?t turn. Any idea what would?ve broken? Is there a belt that would have burned out? The motor? Anthing I could fix myself, or would I need service for this?


If you go to this URL:\015\012\015\012http://www.vacpartswarehouse.com/Hoover-F7452-s/811.htm\015\012\015\012you will an exploded view of your Hoover. By going down the pictures you will be able to see the internal parts of the unit and ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Both drive and slave belts are intact and tight on the Bissell ProHeat 2x. The brushes will not turn. When last turned on, there was a loud snap noise and something is broken in the power head drive train. Can we repair this or is there a service center near the Hastings, MI area? We need this fixed ASAP. Thank you.


Sounds likely you should take it in your drive gears might have a problem ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

I have a bissell 7.5poweramp uprite vacuum with a broken belt for the brush. What size belt would i need to fix this?


I have a galexey 3507a500 and my belt broke and i can't find a replacement belt at any store where do i get a replacement belt for a 5275 belt. ... Vacuums

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

I checked the belt and it has not broken, but when I start to vaccum the spinning head stops, and I start to smell a rubber smell...Do you think I need to replace the belt, I did get some string caught in it the last time I vaccummed, and it did stink like rubber then also...


Yes you do need to replace the belt they stretch out. Think of a belt like a big rubber band if you were to stretch it out and hold a lighter to it the rubber band would stay stretched out. That is the same thing that happen ... Bissell Vacuums

Very end of hose on kenmore 116.35923 upright has broken and attachments won't stay on. need new hose or a way to fix the end of this one.


... Kenmore Vacuums

Broken hose The hose on my Hoover F5837-900 Steam vac Supreme broke away from the coupler on the bottom of the unit - under/behind the recovery tank (solution tube is till attached). It might have gotten pinched in there a couple times. Problem - it was glued in the coupler really well, and I cannot get the whole thing out - hose will be too short anyway - is there a way to fix this or a part I can order instead??


You will have to replace the complete hose asm, part # 90001337 ... Hoover F5837-900 SteamVac Supreme Wet/Dry Vacuum

My kirby is making a very loud noise and somehow the white fan inside has broken. I have the pieces. What do I need to do? I can't find a vacuum repair place near my location. Can I fix this myself?


What you need to do is a long process of taking apart the vacuum apart. Your fan broke so you are going to need a new one. So go to Kirbys website and look up a nearby vacuum store. Or More recommended a Kirby. It is a long process of taking the vacu ... Kirby Ultimate G Bagged Upright Vacuum

Hi all, I have a Janome 234D overlocker and when I try to sew with it, it misses stitches. What could be causing this problem and how do I fix it? I tried rethreading,checked the tension and stitch length dials on the side and I dont have a manual for any instructions, help is desperately needed, regards Wendy


... Vacuums

The suction on my eureka optima stopped working but the roller still works, what might i do to fix it?


Hi there. Most suction problems are due to a blockage. Start with the base and look carefully for debris that is stopping air flow. You may have to remove the base plate to get to the problem. I am including a link to the manual for your machine. ... Eureka 431A Optima Bagless Upright Vacuum

I have a Hoover Steam Vac F5853 and the trigger seems to be broken. I have taken off the cover only to find the trigger just flapping in the wind. What do I need to fix this?


... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The roller on my Dyson vacuum has stopped rotating (I still have suction) I have checked the belt (not Broken) and have checked and cleaned the roller and spindle and also checked the "auto" button setting on the vacuum but to no avail ... Anybody have any clue as to the problem Many thanks


... Dyson DC07 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0906 seconds