Having problems with your Eureka Smartvac 4870 Bagged Upright Vacuum ?

Eureka TheBoss SmartVac 4870 power switch no longer turns off vacuum. Is there an easy fix?

\015 Was using it and it went to turn it off, but the switch didn't work. Had to unplug it. Looked as though the plastic housing near the switch separated a little bit, but not a lot.\012\012Does anyone know of an easy fix?\015

Answers :

Repair Help & Product Troubleshooting for Eureka Smartvac 4870 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka TheBoss SmartVac 4870 power switch no longer turns off vacuum. Is there an easy fix?


... Eureka Smartvac 4870 Bagged Upright Vacuum

Henry hoover Hi all, I bought a spares/ repairs Henry on ebay having been told there was no cable rewind and believing that since I had a spare one in the shed it would be an easy fix. However, poor Henry had his cable replaced to find when plugged in, he tries to start but nothing happens. The motor turns once and just cuts out. If you turn it on and off again it happens again. One whir and turn of the motor, then nothing. It blew the fuses out in the kitchen first time too, so could it be a re


Hi it can be the connector at the end of the Henry cable inside the cable rewind unit happened to us! ... Numatic Henry Bagged Canister Vacuum

The spinning brushes on the vaccum no longer spin, how can i fix this? The vaccum picked up a very small wire from a video game and i turned it off immediately. I unwound the wire but the brushes no longer spin.


You have either broken the belt or more likely the clutch easiest is to replace cleaner head assembly \302\24375ish or call Dyson and arrange a service if you're not DIY inclined but check belt !st ... Dyson Ball DC24 Bagless Upright Vacuum

I have the Eureka Whirlwind upright vacuum. All of a sudden there is no suction- the hose has suction but not main part. I have no idea- but the brush part is not turning??? should I get a new vacuum or is this an easy fix? thanks!!!!!


If the belt isn't turning then it has snapped. Check the top of the hood for two or three crosshead screws; two at the front and one under neath by the left hand side if looking at the upright from the front. Its easy to fix if you take your ti ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

I by accident sucked up the corner of a sheet into the powermate of my vacuum. I turned the vacuum off and pulled out the sheet but now the powermate is no longer working (suction works fine) Is this something I can fix on my own?


These power heads have a kill switch on them. Not exactly clearly labeled. the kill switch reset button should be on the right side of the unit as you look down like you are using it. you may want to try pushing it with the power to the p ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode


... Hoover Vacuums

Motoe runs okay when you turn it on. But when you go to vacuum the room the beater bar makes a horrible noise snd does not work. Is it easy to fix.


... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a t4003rt3 pool timer, it appears its a bad switch, timer not working. I can turn it on with the on/off switch but you have to flip it on and off several times before it catches. Is ther an easy fix?


... Vacuums

I unscrewed the 4 screws on the bottom of my gen 3 mistakenly trying to replace wheels. now it turns on sometimes when the on button is pushed and sometimes it doesn't. is there an easy fix?


Easy fix... wow... um.. maybe. \012\012I think that you may have accidently disconnected the metal arm between the foot pedal and the actual switch. Its not a problem, but you will have to open the top of the kirby unit to see if it has b ... Kirby Generation 3 Bagged Upright Vacuum

AKAI AM-2600 WILL NOT TURN ON?? SWITCH DOES NOT WORK EASY FIX??? FUSES???


No fuse, needs switch replace ... Vacuums

I think the motor for the roller bar is going out, it won't turn very fast and we cleaned the bar, and made sure the belt is on right. is this an easy fix or where can I get repaired locally and quickly?


You may have to take out the roller brush completely and check the side bearings for packed in dirt. Clean out as best as you can and make sure it spins freely. use WD40 to lube it up. Hope this helps. ... Kenmore 25512/ 25513 Progressive Canister Vacuum

Hello, My Electrolux Renaissance is about 12 years old. It worked great for years, but now it keeps turning itself off...about every 15 seconds or so. The bag was just changed recently, too. Is there an easy, (and cheap) fix or should I start shopping for a new one?? Thanks!


Odds are you have an obstruction somewhere. Check all of the hoses and the power head to ensure that there is nothing blocking your airflow. \015\012\015\012Also note that if it keeps popping the front bag door open, that's usually indica ... Electrolux Vacuums

Small blue piece of plastic is broken of a metal rod that appears to connect to the belt turning causing a ver loud noise. Is this the motor assembly and is it an easy fix or should it be taken in for repair?


Try to dismantle the motor assembly and remove the broken plastic that connect to the belt maybe it is the one create loud noise. ... Royal RY9750 Bagged Upright Vacuum

My Roomba no longer cleans the entire room. Rather, it spins in circles and then turns itself off. Is it possible to fix this?


Ah yes. You, or rather your Roomba is experiencing what is commonly referred to as the "Roomba Circle Dance".This is caused by the a sensor called the "Optical Encoder".The image is a before and after cleaning of this sensor. This will re ... iRobot Roomba 560 Robotic Vacuum

Power Issue Hi...my Miele vacuum cleaner (S314) will not turn on, unless I lean it on its side (the side that the power switch is on). I took it apart and the wires are all well attached, and I do not see any issues with the connectors. Is this a common problem with an easy fix? Thanks! Todd


Could be the cord reel causing the problem. Sometimes the contacks on the inside of the reel loose contact and won't conduct. If this is the problem, then you will have to replace the reel cord asm. Part # 06777540, may cost about $150 approx. ... Vacuums

I have the Airvac zx7000 and it won't turn off unless I unplug it from the wall. Is this an easy fix or do I have to replace the system?


... M&S Systems ZX7000 Bagged Central System Vacuum

My honeywell hht-149-hd is not oscillating properly. it will rotate less than a full rotation then stop. the motor is still trying to turn the tower because i hear a rhythmic clicking inside the unit. i don't want to pry it open and void the warranty unless there is an easy fix. please help. thanks!


... Vacuums

My easy flo built in system wont turn on when the


If there is a switch on your hose, it may be broken. Your system powers on from the inlets via two low voltage wires that run from the inlets to the switch/relay at the power unit. Each inlet has 2 spring loaded pins attached to the low voltage ... Easy Flo EF1400 Central System Vacuum

Hoover upright 2000w, HL2005 001 problems:the hoover made a pop sound & turned off. Tried leaving it for 30 mins as suggested in the manual but it still won turn on. Really cannot afford to buy a new 1 & would like to fix it. partner is an electrician so if we have some guidance as to what the problem may be i am confident we can fix it. the hoover is only 18 months old so not very old at all.


... Vacuums

My dyson dc25 just turned off while i was using it first the roller brush stoped turning so i used the hose and now it turned off and wont turn on how do i fix it?


... Dyson DC25 All Floors Bagless Upright Vacuum

Eureka the Boss SmartVac just turned off and won't turn on


Make sure it is not the electrical outlet that has tripped. If not then you basically have 3 choices. Cord, switch, motor. A service tech. should be able to diagnose. ... Eureka Smartvac 4870 Bagged Upright Vacuum

The beater bar is not turning and the belt is still on it and not broke. it turns easy when i do it but will not work when i turn it on


The problem is that the belt is stretched. The belt may not be broken but if it is stretched or worn then it wont be able to turn the brush against the resistance of the carpet. Here is a link to the belt you need and to a manual you can view: ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My hamilton beach convection / rotissier over model 31197 oven button has a shortage in it, how can i fix it the button that turns the oven off and on, if you turn it on the oven doesn't come on but if you turn it counterclockwise all the way and hold it the light and the oven comes on. it was working this morning until i put a pan of biscuits in.


Sounds like a contact problem in the switch-Question: How old is the oven? Is it possible that the switch is worn out? If so-- and lets just say the switch cost $25, plus postage, would you want to invest that mo ... Vacuums

I was using my easy flow central vacuum, and shut it off. When I went to start it up again 5 min later, it would not turn on. I emptied out the filter, and reset the switch. When the reset button was pushed, it started up the vacuum, but the vacuum was not turned on in the house. It can only be turned on from in the garage and not on the actual hose. What is going on?


... Easy Flo EF2300 Central System Vacuum

My vacuum just stopped working, so I don't know what the problem is. I used it in the kitchen to vacuum the hard wood floor. I turned it off, and a few minutes later, turned it back on to finish vaccuuming the kitchen floor. It just would not turn on. I had not unplugged it or did anything to it. I then tried to see if it would work in another plug, and no luck. I'm trying to figure out if it can be fixed or if I need to look for a new vacuum.


When I get most Vacuums that have dies on people most of them the wire has been worn and cut one or more wires on the plug cord. Sometimes the cut can be over looked. Please unplug and check the wire carefully.Also please post the make model a ... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0565 seconds