Having problems with your Eureka Smartvac 4870 Bagged Upright Vacuum ?

Eureka 4870 hose assembly replacement

\015 I cannot figure out how to replace the hose assembly. You cannot take the back of the unit apart as there are some sort of screws that cannot be removed. The assemly will not slide through the narrow hole.\015

Answers :

Boy, it's been awhile since I took one of these hoses off, but I think at least one of those plastic hose guide things has to come off in order to remove the hose. Those screws that look like they cannot be removed are probably torx screws which need a T20 torx scredriver that you can get at any hardware store. That is the most common size torx screw that Eureka uses.
\015\012
\015\012Here is a link to the owner's manual in case you need any diagrams for getting the clear tubes off:
\015\012http://www.eureka.com/service/manuals/70750.pdf
\015\012
\015\012Hope this helps. :-)
Repair Help & Product Troubleshooting for Eureka Smartvac 4870 Bagged Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka 4870 hose assembly replacement


Boy, it's been awhile since I took one of these hoses off, but I think at least one of those plastic hose guide things has to come off in order to remove the hose. Those screws that look like they cannot be removed are probably torx screws which need ... Eureka Smartvac 4870 Bagged Upright Vacuum

How to replace hose assembly on eureka 4870 - Eureka Smartvac 4870 Bagged Upright Vacuum


... Eureka Smartvac 4870 Bagged Upright Vacuum

Eureka air extreme hose assembly replacement - Eureka Smartvac 4870 Bagged Upright Vacuum


... Eureka Smartvac 4870 Bagged Upright Vacuum

How do you replace the hose assembly on the Eureka 4870 vacuum? Which screws do you have to take out and do you need a special screw driver?


... Eureka Smartvac 4870 Bagged Upright Vacuum

My mother purchased a replacement hose assembly for a Bissell ProHeat 2X and the part was shipped without any instructions... While I am pretty handy, my issue is with the supply tube, and I cant figure out how to accomplish the replacement, and as its not MY vacuum, Im hesitant to start taking things apart.I just need instructions to replace the entire hose assembly.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

I have Optima, 12amp Eureka vacuum, Model 431, AXZ type and the extension hose for cleaning corners and edges --the plastic part that the attachments fit into has a piece broken off and tools don;t fit anymore. It looks like the hose attachment can be replaced--can it be and if so--where can I get a new hose attachment. It seems it is cheaply made of plastic and really shouldn't have broken a piece off.


... Eureka 431A Optima Bagless Upright Vacuum

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@


Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

I'm using a Eureka maxima 12 amp vacuum and where the hose is connected to the vacuum by a screw that part is broken where do I find a replacement hose that includes the clear plastic part that I can attatch to the vacuum?


... Eureka 4700A Maxima Bagless Upright Vacuum

I have an Eureka Enviro Vac, I have replaced the filter, cleaned the hose and it still won't pick anything up. The brush is turning and there is suction in the hose. What else can I check?


... Eureka Vacuums

Bissell 1631-1 Need replacement Water Hose Meter Assembly


... Bissell 1631 PowerSteamer ProHeat Canister Vacuum

I need to replace the hose and can't find one. the model #is 5893avz. this is a upright eureka vacum cleaner


I called the plant and they are sending me one. thamk you ... Eureka Vacuums

I am looking for a replacement hose for modle # 1784 B. Eureka


... Vacuums

I need a replacement hose assembly for the hoover steamvac jr. any suggestions where i might find the part?


Only through a Hoover warranty/ service center if still available. If not save your hose ends and find a different hose with adaptable ends ... Hoover F5411 SteamVac Jr. Canister Vacuum

Where can I get a replacement hose for the eureka 431A optima bagless upright vacuum


You could try Espares.co.uk if your u/k ... Eureka 431A Optima Bagless Upright Vacuum

I need a replacement hose - Eureka 3041BZ Upright Vacuum


You can get the nose part number and order the part at this URL:\015\012\015\012http://www.VacPartsWarehouse.com/Eureka-3041-Enviro-Vac-s/1859.htm ... Eureka 3041BZ Upright Vacuum

Hoover Windtunnel T-Series UH20700 9 mos old. Keeps clogging in hose just above the beater brush assembly. I think it clogs because the suction is too weak to pull much through. Primary filter is clean and HEPA filter is replaced. Even when everything is unclogged, suction is weak compared to another unit (same model) that a friend has. Any ideas?


... Hoover UH70120 WindTunnel TSeries Rewind Bagless Upright Vacuum Cleaner

I need to replace the "hose assembly" for a PANASONIC MC-E852. wHERE CAN i GET ONE? Ykanks


I bought a new one. ... Panasonic Vacuums

Help!!! I bought a replacement nozzle valve for a hoover steam vac hose and I can't get it back in right. Does anyone know where I can find an illustration of this assembly??


Hessco.com ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Where is schematics online to replace lower hose assembly part


There is no schematic that I am aware of. I can tell you that from experience that this repair is very difficult. Basicaly the upper and lower handle unscrew along with the tank base, the hood comes off. the lower handle will split but not comes comp ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

How do i disassemble the foot to replace the lower hose assembly ont he bissell 5770


... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

How do i replace the water channel/ hose assembly on a Hoover Floormate H3000 ?


... Hoover Floormate H3000 Upright Wet/Dry Vacuum

Hoover F6028-900 Need to replace the hose assembly but am unsure of how to get the old one disconnected.


It's probably harder to explain than it is to do. \015\012\015\012Take off the recovery tank and underneath it you can see where the hose attaches to the unit. On the bottom side of that inlet is a clip that latches the hose ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

How to open 116.23512301 vacuum canister AC section to wire in replacement 4370608 cable assy. This assembly contains the receptacle that powers the hose. I found the two screws below the bag cover, but can't figure out how to release the end near the retractor lever.


... Kenmore Vacuums

How to replace the cord rewind assembly on a AS1101 eureka vacuum


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0518 seconds