Having problems with your Eureka Smartvac 7975 Vacuum ?

Eureka 4470 The suction works from the hose, but not from the base. I do not know how to remove the cover to check the inside.


Answers :

Take apart botem 1st cheak the hoses for sumthign in there ok stick a hanger in it poke it out from bottem side under
Repair Help & Product Troubleshooting for Eureka Smartvac 7975 Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka 4470 The suction works from the hose, but not from the base. I do not know how to remove the cover to check the inside.


Take apart botem 1st cheak the hoses for sumthign in there ok stick a hanger in it poke it out from bottem side under ... Eureka Smartvac 7975 Vacuum

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

My eureka optima upright bagless vaccum has VERY low suction using the floor part. the hose has excellent suction. i removed the little translucent door underneath and there were no blockages, i cleaned the brushroll thoroughly and that hasnt helped either. i know this probably isnt recommended but i turned it on to the floor setting with the brushroll off and stuck my fingers up the intake as far as i could, the suction was good further up but it just seems to stop down at the base. because i s


I will try and help here. Is the sole plate on the bottom of the vacuum complety on and there are no visible cracks along the seam where it meets the body? This is the usual cause for this. Onc you take of the plate to access the roller and brushes, ... Eureka 431A Optima Bagless Upright Vacuum

No suction. filter and hose clear. motor high pitch. don't know how to remove cover to check motor.


Something is clogged somewhere start from bottom and foolow suction path all the way through. wht kind of vacuum? ... Vacuums

Suction Cover The suction cover of my Eureka Deep Steam 2575A is broken - the tabs snapped off of the cover so I am unable to screw the suction cover back on. I need to purchase a new suction cover but can't find one anywhere. Anyone know what I can do? thanks


The exact same thing happened to me. i just called and ordered it from eureka. the number is 1-800-282-2886. the cover cost 13.07 and the s ... Eureka 2576A Steam Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom


Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hi. I have Dyson dc08 hepq+. Thet problem is its not having suction .I checked inside the pipe and foot , ery thing is fine. And if i take the whole dirtbin out ...machine workes fine. when i put ery thing back ....as soon as i start it , after 2 second machine change its voice...and loos suction. I think its just happen because ...the saftey yellow valve inside the machine turns up because the dirt drum is blocked inside some where. Any suggstion ...what can i do with it. I m tahnkful in avance


Hi its Darran at Dyson.From your description of the problem, it sounds as though the bin inner is missing. To confirm this, if you remove the cyclone and bin from the machine, then separate the 2 pieces as if you were going to empty it, w ... Dyson DC08 Hepa Allergy Bagless Canister Cyclonic Vacuum

OUR DYSON 07 SWEEPER HAS VERY LITTLE Vacuum, have cleaned all filters and hoses, on line troubleshooting has said to check soleplate being on correctly, we have done this, still does not have good vacuum, belts are covered by a housing, the video that shows the changing of the belt is not the same, I need to know how to remove the cover to check both belts and any help in gaining the vacuum


This video shows you everything you need to know ... Vacuums

Brushes stopped The brushes stopped turning while using the cleaner. I removed the brushes to see if the spindle was broken, it wasn't. I then removed the top plastic cover and checked the switch that engages the brushes; it didn't seem to be moving correctly. There's one spring on the switch - should there be two? Or do you think something has broken on the inside? Thanks for any help


Most likely the turbine is bad, it may just be clogged up, you can take it apart and clean it out real good. That may work, but it may not. Sometimes it is best to replace the turbine. ... Hoover F7431-900 SteamVac Vacuum

I cleaned out the hose and removed brush to clean and checked belt. Everything seems to work but will not pick up or suction on carpet. The hose is totally clear from clogs. I can see the floor from one end to the other. What am I missing that might be causing lack of suction?


Hi troupdavid,I see that your Vacuum is having issues with it suction, you mentioned that you took it a part to clean it, see steps below.\015\012\015\012Check if everything is inserted prope ... Hoover Tempo Widepath Upright Vacuum - Blue

Hoover Alpina 2 1300 cleaner. I need to split the upper and lower casings to check that the switch is working. I have removed the screwa in the area around the bag, but now need to remove the switch and cable rewind covers, as I assume there are more securing screws under them. Can you advise how to do it please?


Move covers (forcibly !) away from the centreline of cleaner then move to rear until released. The covers are held by slide catches on inner edges. ... Vacuums

The retracktable power cord on my Panasonic MC-E7103K is jammed inside the machine. Does anyone know how I remove the cover after removing the two visible screws? Brian


... Panasonic Vacuums

No suction hello, there was a rubber smell then no suction. i'm thinking it needs a new belt but don't know how to remove the cover to replace. is it a complicated procedure. is there a diagram available? don't have any info here. thanks, leslie


Flip the machine upside down and remove the four screws from the baseplate. Replacement should be fairly self-explanatory from there. If it's a self-propel model, note that the v-belt in the front WILL look loose normally, so it does not usually requ ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do I access the motor to my eureka capture? It has no suction at all but turns on just fine..filters are cleaned and there are no clogs or leaks on the hose....im thinking there must be something stuck in the motor possibly but there are soo many screws that im having trouble removing them all....whats the best way to access the motor to check it??


... Eureka Capture Upright Vacuum Vacuum

I purchased a brand new Eureka Pet vacuum, sorry don't know exact name but it the one that has the self cleaning duster on it. Last night I used the vacuum on my carpet, it was working fine until I accidently sucked up the corner of a scarf that was hanging off a couch. I shut the vacuum off, pulled out the scarf and and resumed vacuuming. Much to my dismay the suction on the vacuum had ceased. Can you tell me if there is a reset button on the vacuum? The vacuum does not appear to be damage


If the motor is running, there should be suction. Possible problems depend on whether it's a canister or upright and are:\015\012A clog in the hose, UR or canister. Detach hose. Drop small coin in one end and lift hose causing it to roll out ... Eureka Vacuums

We have Nilfisk Tempest 1500W bagged cleaner. It just stopped working and I have taken off top cover and all wires/contacts look OK. But power still not getting through I assume. The retractable lead goes into base and cant get to this area. How do I check main lead or perhaps you provide details of serviceman. On North Shore, Auckland, NZ.


... Vacuums

I have a DC14. About a wk ago it was making loud sound and bar stopped turning. i unclogged everything....now the suction works great. However, the bar still wont turn. The belt inside is still intact and isnt loose. Several solutions suggested resetting the "Red" button...i have searched the vacuum over and over. there is NO red or any other color reset button. The bar is set down perfectly in there, the cover plate is installed properly. What other problems could there be? Or do i just need to


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

It starting to put out a hot type smell. I have tried cleaning the filters real well and even tried to see if there was problem with the ozone filter. We have checked and could not find a jam. I know the hose has excellent suction. The vacumn works but the intelliclean sensors will not. It only takes about 15 seconds or so for the odor to start. Then it gets real strong and it makes my eyes water


Hi,The hot smell could be from the belt or the motor. Turn it on for a moment, turn it off, then flip it on its side and smell the belt that drives the brush. If that is where the smell is coming from, then your belt is burning up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

My 4 yr old Nilfisk vacuum cleaner has been working fine up until now. But suddenly, it has hardly any suction power and also, hot air seems to be coming out thru the vents on top and also thru the space that's normally used for blowing air OUT....the outlet with the retractable cover located close to the part where the power cable comes out of and retracts into. I've checked the filter and the hose and they are not clogged...I have also put in a new bag. Not keen to buy another vacuum cleaner u


Hi there SmartAlec from Nelsonvacuums.com.au here.It sounds like a blockage of some kind. The best way to find it is to set the machine up for normal vacuuming and remove o ... Vacuums

My Dyson vacuum works fine for cleaning the rug but the hose doesnt get any suction at all. I removed the hose and all the parts around it that I could and dont see any clogs or broken pieces. I lost my manual so I dont know if this is addressed, or if there is a switch Im not flipping. Gave it a thorough look but found nothing.


Hi there,Sorry to hear you're having a problem with your DC07. If you have suction through the cleaner head but not through the wand, it sounds as though you have a blockage. Although you say you've already checked for these, you may find ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The vaccum has been cleaned and checked but the brush is not rotating and no suction at the bottom, but through the hose. In reading the instructions to remove the brush cover it says to lift tab one and release 2-4. Where is the tab for tab 1 can not find anything for tab one to be able to lift, nothing there any ideas for help would be greatlly appreciated/


3 on the front and one on the back. where the belt runs ... Bissell 6594 PowerForce Bagless Upright Vacuum

I have a Hoover SteamVac spot cleaner, model F5505. This is an older cleaner. It has no suction and I believe the hose may be clogged, but don't know how to remove the hose and check it.


... Hoover F5505 SteamVac Spot Vacuum

My hose no longer works no suction buth the vacuume still works how do i fix I checked the hose checked the filters nothing works to get my hose so it has suction.


Check the following after unplugging the power cord from the outlet.\012\012- Check for suction at the back of the unit, after removing the hose where it attaches to the back of the vacuum. If there is NO suction, the machine will need to be ta ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Recently purchase SC-N500 vacuum cleaner. Worked well only the first 2 times I used it to clean up plaster dust from floor after sanding. Since then it has not worked at all well wiht very poor suction. Fluff gets stuck in the hose and has to be manually removed. Suction power is very poor. I have washed the filter to remove the dust with no difference. Who do I contact in Brisbane to service or assess the problem further.


... Sanyo Vacuums

Suction stopped. Roller and belt working-in fine order. Checked hoses have not found any blockage. Blowing out air or sucking so little can't feel it with hand on hose end. Help!


Either a blockage or the main air filter is blocked , some it can be washed and others it must be replaced I would check the owner manual and look at the filter, foam ones can and usually have instructions where they install to wash them. ... Hoover Tempo Widepath Upright Vacuum - Blue
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1150 seconds