Having problems with your Eureka The Boss Bagless Stick Vac - 166DX ?

Burnt smell..not the belt...shaft and brushes are cleaned and moving...what is it! HELP!

Answers :

Check your switch eureka's are bad about switch's burning up.
Repair Help & Product Troubleshooting for Eureka The Boss Bagless Stick Vac - 166DX

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Burnt smell..not the belt...shaft and brushes are cleaned and moving...what is it! HELP!

Check your switch eureka's are bad about switch's burning up. ... Eureka The Boss Bagless Stick Vac - 166DX

Roomba Discovery My Roomba turns on and moves but the brushes won't turn. Someone told me that I had forgotten to put in the yellow and black end bearings, but I did. Help, I miss my Roomba I have a Roomba 530, I have had it for 2 weeks and really loved it. I have followed all the cleaning instructions etc.. Then the Roomba wanted it's brushes cleaning "please clean Roombas brushes" So thinking that something was stuck I removed and cleaned the brushes, (yellow tabs on and in place by the way)

I read somewhere that you need to clear the software in case there is a glitch. To do this, take the battery out and then, simultaneously hold down the "spot" and "clean" buttons for 30 seconds. Replace battery. This has worked for my Discovery model ... Roomba Robotic Floor Bagless Vacuum

My roomba won't go forward; it just rotates right ~90 degrees and then left ~90 degrees. I've cleaned the brushes, taken it apart and cleaned the brush gears, popped off the front wheel and cleaned the hair off that, taken off the front bumper panel and cleaned off the cliff sensors. Please help!

Compare your Roomba to the video on http://www.eesolutions.ca and look for the fix. ... iRobot Roomba 550 Vacuum

Keep getting message 'please remove and clean Roomba's brushes'. Have removed and cleaned brushes and even fitted new one's but still getting message. Also brushes sometimes rotate, sometimes not and not picking up very well at all. Help!

Must be your inbox is full, Delete old / unwanted messages. It should resolve the problem ... iRobot Roomba 500 Series Virtual Wall Lighthouse 80201 Robotic Vacuum

I noticed that the little side brush doesn't turn anymore and the Dirt Dog stops about every minute now so I have to keep turning it back on! I have dismantled the brushes and cleaned everything out but that didn't help at all. It doesn't really come apart any more than that for cleaning. Any suggestions as to where my problems may lie?

... iRobot 1100 Dirt Dog Bagless Robotic Vacuum

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.

Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula

There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums

Hoover Max Extract LS F6056900 Hand Tool not working / Cleaning Solution I need to know what I need to get in order to have the hand tool work on this model. Also, what cleaning solution is best for pet stains? Tried cleaning, pre-treating with Spot Shot and towel and/or scrub brush, then cleaning, still doesn't work. PLEASE HELP!!

... Vacuums

I recently purchased a Hoover SteamVac to replace an old one because the brushes would not turn. I used it last week and then tried to use it last night and the same thing happened w/ the brand new model - the brushes won't. I've cleaned the brushed, the filter and everything else I can see. Can you help?

Those things are a waste of money you better off renting one. but the only thing i could think of is that something is stuck or your belt came off track ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.

If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum

Vaccum brush not working. Filters clear of debris has been smoking will not **** anything up help! I cleaned the brush up, cut hair out, etc. Still the brush will not turn and it smokes a little, is this a belt problem?

Yes you need to change the belt. Here is a link to the belt you need and to a manual you can view:Bissell Lift-Off Revoluti ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?

Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

Hi my dyson is not sucking up very well when i put it on its side and switch it on the brushes are not going round when i put the white dail to on at the bottom the brushes go round but it makes a terrible noise i have cleaned the brushes checked the soleplate is on correct and taken the clear hose off and checked for splits the suction is there when i have been checking these things hope you can help thx

Hi there,Sorry to hear you're experiencing a problem with your cleaner. Please get in touch with us, free, on 08002980298 (UK), or 1866MYDYSON (US). We can run through some checks over the phone and provide you with the assistance you nee ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The vaccum has been cleaned and checked but the brush is not rotating and no suction at the bottom, but through the hose. In reading the instructions to remove the brush cover it says to lift tab one and release 2-4. Where is the tab for tab 1 can not find anything for tab one to be able to lift, nothing there any ideas for help would be greatlly appreciated/

3 on the front and one on the back. where the belt runs ... Bissell 6594 PowerForce Bagless Upright Vacuum

No suction i have a bissell lift off revolution vacuum. I have cleaned all the filters and emptied out the canister made sure that the hoses are not plugged but it will not pick up unless you use the hose. the floor brush is clean and still no suction coming from under the vacuum... could you help me please

Is there a blockage in the small hose in the bottom of the machine \015\012take of the pod and you will see the small hose, \015\012Is the main hose pushed into the bottom housing ... Bissell 37603 Upright Vacuum

Roomba Stops I've had a Roomba for about 2 months. Lately, it runs for about 45 secs, then stops, makes a two-tone (descending) sound, and flashes the CLEAN button while the STATUS button is red. I've emptied the dustbin on it. Can you help? I am seeing the same problem on my roomba today. I cleaned all that I could., the brushes, the pins on the sides and all that and it still gives the same problem..Any other fix?

Run your roomba through a self diagnostic test. I have posted the link below. Tell me your findings.\015\012\015\012\015\012http://mysite.verizon.net/gsplews/Diagnositic-Tests_Proc.v.0.5.htm ... iRobot Roomba 4210 Bagless Robotic Vacuum

I caught a hidden shoe lace in my dyson 17 beater head....shut it of quickly....removed the lacing from around the head....loosened the three screws on the botton of the head....cleaned it out from whatever little dust there was....checked the heads belt reset the roller brush into the head...but alas no beater brush action. what to do?(I've had my dyson about5 months....HELP!. thanks, Jan Selman

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Neato XV11 Vacuum and despite cleaning the brushes completely the machine no longer vacuums because it displays the error messages that it brushes are stuck and to the debris. Please Help Thanks.

... Neato XV11 Vacuum

I have a Dyson DC14 It started making a high pitched squeel so I took the filters out and cleaned them and i checked all places that pull out on the vacume to see if there was anything clogged. I also cleaned the roller brush. but when I turned it on, after a couple of seconds the sound came back again. can you help

Sounds like motor bearings are gone .... sorry. ... Dyson Vacuums

The rotating brush bar won't turn after i cleaned all the tangled hair and string off of t ,... I don't think i positioned the brush bar back in to the correct place that will connect ,,can you PLEASE help me?

Hello pmoongoddess. Here is a list of dyson vacuums with the parts diagrams for each one. Find your model and then open up that parts diagram showing the rotating brush component. It will show you exactly how it is positioned. I hope this helps. ... Dyson Vacuums

I have a roomba 435. I've had it for about 3 months, it had been working great until it started to sound a little different (louder). Now I noticed that it doesn't pick things up, it just pushes them around, I then discovered that the brushes aren't turning. I cleaned them out, no parts are missing. Brushes still won't turn. Help please.

Hmmmm....I know exactly what this is... Think back...the last time it was used when it worked...did it pick up something like a sock or get stuck somwhere?????? If you look on Ebay, it is polluted with this model Roomba. There is a gear that strips. ... iRobot Roomba 410 Robotic Vacuum

Roomba is not picking up dirt but does pick up dust. That is, the dust chamber has dust in it but the dirt chamber is empty. The brushes don't have any fluff on them either which is not normal. The fan is blowing out plenty of air, the filter has been cleaned but we suspect the brushes aren't turning. an you help?

... Roomba Vacuums

I have a Bissell proheat clearview 12 amp 5 cleaning rows of dirtlifter powerbrush. It won't shoot the cleaner to the brushes. I cleaned the filter, checked the belt, water is full, and soap dispenser is full. Still no soap going to rug. Can you help? Thanks

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

5 yr. old Miele s514 Turbo plus's power nozzle brush seems to disengage temporarily, stopping the spin. Then it seems to re-seat itself after a few seconds, then starts spinning OK. I keep the nozzle brush very clean, so there is no hair or yucky stuff to cause it to jam. Please help.

I had a White Pearl with same problem. As I moved the hose/wand the brush motor would start stop. Find out where the circuit opens up by holding one part and moving the part that connects to it - 1) where the hose plugs into the cleaner, 2) the swi ... Miele S514 Solaris Turbo Plus Vacuum

I have a Hoover Steam Vacuum, All Terrain, and the bristle brushes are not rotating. They appear to be seated properly and, the entire vacuum is clean and free of lint, hair etc., so everything is working properly except the brushes do not rotate. Any help would be greatly appreciated. Thank you.

I checked the owner's manual and the parts breakdown for your model F5807. Both showed that your model has a stationary brush strip and not rotating brushes. Is F5807 the correct model number? ... Hoover F5807 SteamVac Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0999 seconds