Having problems with your Eureka the boss power plus ?
A non rotating brush head
Belt is broken but brush cylinder is seized up.
Repair Help & Product Troubleshooting for Eureka the boss power plus
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
Brush head not rotating. Press rotating button and head does a little jump but no more. No build up of debris on head.
... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum
Cleaning rotating brush on vacuum head
... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I bought a G5 (w/ all the attachments) at a lawn sale. It works as in the motor seems to run fine and the brush head rotates, but.....there's no suction. Is there another button or lever I need to push/pull?
This link is for the manual it may help you.http://kirby.110mb.com/docs/kirby_sentria_manual.pdf ... Kirby G5 Bagged Upright Vacuum
Kenmore canister. Brush is turning but spitting all dirt under and out the back of the head. I guess the suction is very weak or non at all. What is reseting overload protector doesn't work. Haven't tried yet but just in case. THANKS!
I would look to see if there is a clog. that would be the only reason that the power head would be spitting dirt in back of the power head. check the hose. ... Kenmore Vacuums
I've had my Kenmore Progressive canister for at least several years and never had a problem. Now, the carpet head brush does not rotate, it's not getting the connection unless I push down maintaining pressure on the handle.
Hi, try pushing the reset button with a pen or paper clip. If that doesn't work, the motor may need to replaced. If the reset button is stuck, if the reset button is stuck, use a pair of tweezers to pull it back out......\01 ... Kenmore 25512/ 25513 Progressive Canister Vacuum
I have a dyson dc07 with a malfuncitoning clutch diagnosed here on fixya. I've replaced the clutch and the grinding noise when the clutch is engaged for carpet and non rotating brush problem presists. This is after replacement of the clutch with a new part. Install of the new part went well and there are no otehr apparent problems with the unit. Ideas? The unit is only a couple years old and not used that much on carpet. For an expensive vacuum I'm not that impressed with it at this point.
Greetings from GoVacuum,\015\012\015\012If you have replaced the clutch already, then this can really only be one other problem, and that is the roller brush. If the roller brush's bearing have locked up, and the brush is no longer spinn ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
I need to know how to disassemble the power head for my pet vac. the brush no longer rotates, and it severely limits the quality of vaccuming. we have dogs, so it's really important for this thing to work at it's best!
... Euro-Pro Shark 18Volt Pet Perfect II Cordless Handheld Vacuum Cleaner
The brush head on our Dyson DC34 rotates for a second and then stops even tho vacuun still operating - how to fix?
... Dyson Dc34 Animal Handheld Vacuum With Longer Run Time For Pet Owners
I just accidently vacuumed over a bag, realized what had happened and pulled it out before it got stuck further into the head of my Hoover Wide Path. I shut the machine off, and when I turned it back on the brush won't rotate. Anything I can do?
IS THERE A RESET BUTTON ON THE MACHINE? SOME OF THE MATERIAL FROM THE BAG MAY BE WOUND AROUND A PART OF THE BRUSH. ... Vacuums
Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o
Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum
Dyson 18 slim the rotating brush bar will not rotate. Was working fine until I got the edge of a tablecloth caught in the brush, pulled it out ok but now the brush will not rotate fast, but will rotate by hand . Any ideas.
If the DC18 has a proteted belt then it will have to be replaced by a Dyson engineer or repairer. If the cleaner has a removable sole plate where the beater bar is then remove it and replace the belt - sounds like the belt has snapped and needs to be ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum
Dc11 dyson the brush head turns very slowly but when i take brush head cover of (the yellow part) and put my hand over the suction inlet part the brush head turns really fast. Have cleaned out collection chambers eg the hoover bag have washed the sponge with the little pictures of taps on it what now . thanks alan
I have taken the brush heads off and pulled all the hair out of the small gap between the chrome shaft and the plastic gear housing. Then a small amount of 3-in-1 oil into that gap to lube the internals and just a little through the air intake on th ... Dyson DC11 All Floors Bagless Canister Cyclonic Vacuum
Kenmore 116.23513301 Motor runs, but the brush will not rotate. Every time I hit the overload reset button, it will rotate for about a second then stop. I replaced the belt and cleaned around the brush, but the brush still will not rotate. Any help you can give me would be greatly appreciated.
If the motor on the power brush is running the belt is bad, if the motor on the power brush only runs when you push the overload, the overload is bad. ... Kenmore 22812 Bagged Canister Vacuum
Bissell proheat 2x carpet cleaner when the switch is turned on the brushes rotate fot 2 seconds then STOP ,, iIf I turn it off and on again ithe brushes will rotate for 2seconds and STOP again ?? brushes rotate for
Hey, sorry to hear you're having difficulty with the brushes. Here's a quick link to troubleshooting steps.\015\012http://www.bissell.com/FAQDetail.aspx?id ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
F7220-900 The brushes do not rotate, motor seems to run properly. Brushes did rotate very slowly but stopped when put on floor. Brushes rotate when turned by hand.
Clean the lint filter first. Remove both tanks. Lay the cleaner down(unplugged from power of course) Below the brushes(directly behind them) to the right side as you're looking at the underside is the filter. Squeeze the filter frame, lift it and pul ... Hoover F7220900 SteamVac V2 Upright Vacuum
Now that I just fixed my Lux Legacy canister vacuum, I need help on my other Electrolux Regency Series upright! The vacuum works fine but the rotating brush does not work and the brush motor does not turn on. Tried cleaning the brush and hitting hte reset button to no avail. This upright has a triple setting switch and I checked the each of the wires seem to be attached. Tried rotating the brush by hand and it would not budge. Was going to "encourage" the brush to turn with a set of articula
There are a couple rectangular holes on the bottom of the power nozzle, beside the wheels. These have tabs in them that need released with a standard screwdriver. \015\012 ... Vacuums
I caught a hidden shoe lace in my dyson 17 beater head....shut it of quickly....removed the lacing from around the head....loosened the three screws on the botton of the head....cleaned it out from whatever little dust there was....checked the heads belt reset the roller brush into the head...but alas no beater brush action. what to do?(I've had my dyson about5 months....HELP!. thanks, Jan Selman
... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
Hoover steam vac, brushes won't rotate, have cleaned filter by brushes, removed brushes and they rotate okay when off steam vac, tried to ajust level for carpet cleaning and brushes still don't move
There are three things to check when experiencing 'no spin' on the cleaning brushes. 1) Check the small pull out filter screen under the machine. It must stay clean for air to pass to the turbine which powers the brushes. 2) Check that the long shaft ... Vacuums
Hoover WindTunnel S3765. The motor spins and the belt turns when I turn the brushes on, and the brushes will spin. The problem is that when I do this on carpet, the brushes stop spinning. As soon as I pull the "head" off the carpet, the brushes spin again. It's almost as if the vacuum suction is too great. I took the head apart and watched the motor turn the metal spindle that the belt rests on, and the belt turns as well.
The belt is stretched and needs replacement.(Belt # 38528036) . The brush is not turning against resistance. ... Hoover Vacuums
My Kenmore progressive upright vacuum, model 11635923500 has a problem with the brush rotating. Sometimes the brush will not rotate until the unit in lowered way down, like the activate switch has rotated. Can I get inside the unit to check the switch, if so were do I look
... Kenmore Vacuums
Hi. I have a DC 24 which when brush rotates makes a very loud noise. I have replaced the brush and side bar. The side bar appears very loose. The noise stops when I switch the brush rotation off. Any ideas ?
Hi there,I'm sorry to hear you're having difficulties with your DC24. If the cleaner head seems to be making an unusual noise during use, you may want to check all the parts are correctly assembled, and that the cleaner head and brushbar are ... Dyson Ball DC24 Bagless Upright Vacuum
My pet hair eraser rotating brush does not rotate. I read the manual and cleaned the brush and placed it back correctly, but it is not working when I am using it. If I lift the vacuum from the flour, it starts rotating so I think it is the matter of the amount of contact to the flour. what should I do?
... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum
Rotating brush Hello, my kenmore rotating brush is not spinning at all, and its causing the motor to cut the belt. should i get a new brush? Thank you.
Sounds like the brush roll has an end that is melted or frozen up so it won't move, in which case you need to replace it. ... Vacuums
We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a
Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums
No matter how many new belts we put in the brush will not rotate when it touches the floor. If you hold it straight up the brush rotates like crazy. Why is the brush not cleaning the floor. Yes, I have the right belt. It is R we have the boss. 12 amps. Model 4870
There is probably an accumulation of slippery stuff on the shaft that drives the belt. You can scrape it clean with a sharp knife or a razor blade. You might need to use some kind of solvent to get it clean, and if you do, be sure to follow up wit ... Eureka Vacuums