Having problems with your Eureka the boss smart vac ?

How do i replace the correct screws for the bottom plate

I lost the screws when replacing the belt i need new ones

Answers :

Repair Help & Product Troubleshooting for Eureka the boss smart vac

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Dyson dc07 The rotating brush on the bottom of my vacuum was filled with strings. I removed the brush by undoing all yellow plastic screws from plate. Removed all strings and replaced as best I could and it was hard to get the brush back in and the belt around it. I dont have my manual but it fits so it should be correct....? Right? No, not true, because when I turn it on and try to and vacuum (by lower canister with foot release) it makes that terrible ratching sound). Please help


The loud ratching is a warning to tell you that there is something stopping the roller bar from rotating this is a very common thing lay the machine on the floor front side down take off the bottom plate and just check the belt is in the centre of th ... Dyson DC07 Bagless Upright Cyclonic Vacuum

How do you replace a belt on the a Simplicity Synergy vaccuum? Removing the 2 screws on the bottom plate allows you to access the roller, but doesn't give you access to the drive motor. Any ideas?


... Simplicity 7850 Premier Bagged Canister Vacuum

Dear Sir or Madam, I own a black 23 x 47 x 7 mm Rowenta lighter. It has a screw on bottom that I cannot remove. What is it hiding ? Is this lighter refillable ? Is there a flint to replace ?. I've found on your site the following : "By jbbiii on Apr 06, 2009 Father died and left me a Rowenta lighter purchased in Stutgart in 1952. It has a screw on bottom with spring to replace the flint, but I cannot figure out how to open the bottom to replace the cotton wadding which I can see through the hole


Hello \015\012The flint should be near the striker.Or the thumb roller,usually below it.\015\012As old as it is you may not see it beacause its worn down.\015\012\015\012Maybe taking it to an antique store or a smoke shop woul ... Vacuums

Hoover Wind Tunnel U6458-900 Self Propel doesn't work - via other expert advice here for other models of Hoover - I'm thinking it is the actuator that needs to be replaced as I can see the cable does not connect to anything on the bottom. My problem is - I can't get the cover off. Been trying for a couple of hours. I removed every screw I can seem to find but something is hold it down. I also am wondering if/when I do eventually get the cover off, would I need to replace the cable when I replac


On some models there are hook/springs that hold the cover of the base snug. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

What size screws are needed for the bottom plate of a Hoover U5061-900, the screw part number is 012-21447121


Any coarse thread screw about 1/2" long will work. There's no real "threads" inside, its just cut when they put the screws in at the factory. ... Hoover Elite U5061-900 Bagged Upright Vacuum

Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the


Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums

The roller is not spinning. I took the bottom screws off but and replaced the belt but am not sure how to replace the clutch. I think that is what it is anyways, the thin silver bar that controls if the roller is spinning or not


... Riccar 8850 Vacuum

Need to replace belt on Eureka Powerline 12.0 vac. Screws look like Torx head or something on bottom of vac. Are those the screws that need to come out for changing? If so, what size do I need?


No, do not remove the torx head screws for a belt change. If there are any screws that need to be removed for the belt change, they will be phillips head. What is model # of vac?? ... Eureka Vacuums

I also have a Hoover upright and I need to replace the electrical cord. I have dimantled the back, where the tools are stored, and the hose. I still cannot find the screws or whatever, to get to the area behind the cord, so I can replace it. I think I will have to take off the bottom too. Has anyone out there tried to do this? It seems crazy. This machine works great so I hope I can also put it back together. Thanks for the help.


Since I do not know your specific model I can only supply you with general instructions. Be aware that most of the time you only need to gain access to the on/off switch to replace the power cord. Also Make sure that you are replacing the existing co ... Vacuums

I have a 20 yr old upright U4689-910 with a broken agitator belt. I have a replacement belt. I have removed the L shaped plate on the bottom of the vac. It is not clear to me how to replace the belt at this point.


If it is like the older hoover models you need toDISCONNECT FROM MAINS FIRST then lift out the roller with the brushes on it, grip firmly at both ends and pull away from body of hoover, loop the belt over it and push it back in. Make sure you l ... Hoover Vacuums

I have a Hoover U5750-900 Windtunnel Bagless and For some reason, the belt has been replaced correctly, but there is a very LOUD vibration/rattling coming from the agitator, like it's hitting the assembly/bottom plate? Is there a reason that there would not be enough distance from the plate?


... Hoover U5750-900 WindTunnel Bagless Upright Vacuum

Fan replacement I found the part to replace my broken fan. I've remove many screws, but I can't remove, what seems to be, the obvious plate to get to the broken fan.


Http://reviews.ebay.com/KIRBY-VACUUM-REPAIR-HOW-TO-REPLACE-THE-FAN-IMP ... Kirby Ultimate G Bagged Upright Vacuum

Eureka Fantom Thunder 12V/older model Need instructions on how to change belt and headlights.I could only find 1 screw on the bottom plate none on top plate. Thanks N J


There are two screws on the Fantom Thunder (It was not made by Eureka though) on the back of the unit just above the rear wheels. Remove these two screws and the top cover can be removed to get to the brushroll, belt and headlights. I believe the lig ... Vacuums

Bottom plate screws


They don't unscrew they only turn 1/4 of a turn then pull open watch this video ... Dyson DC26 Bagless Canister Cyclonic Vacuum

I have a Fuller FB80 and am unable to remove the bottom plate for cleaning. I can only find 2 screws holding it on, but I'm afraid to force it in case I might break the plastic.


... Fuller Brush FB80 Bagless Upright Vacuum

I unscrewed the 4 screws on the bottom of my gen 3 mistakenly trying to replace wheels. now it turns on sometimes when the on button is pushed and sometimes it doesn't. is there an easy fix?


Easy fix... wow... um.. maybe. \012\012I think that you may have accidently disconnected the metal arm between the foot pedal and the actual switch. Its not a problem, but you will have to open the top of the kirby unit to see if it has b ... Kirby Generation 3 Bagged Upright Vacuum

I have a Kirby G5 and need to replace the gear drive shaft, as the lever inside fell off and the shaft came out. (Common problem by the sound of it.) How do i remove the actual gearbox itself. I have removed the 3 screws on the bottom, but it's not coming out. What's stopping it from coming out? Do i need to remove the gearbox drive belt first? If so, how do i get to it? Thanks in advance.


HELLO, JUST USE THIS GUIDE! :0)http://reviews.ebay.com/REPLACING-OR-REPAIRING-KIRBY-VACUUM-NEUTRAL-DRIVE-PEDAL?ugi ... Kirby G5 Bagged Upright Vacuum

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci


If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

Vibrating When I turn on the vacuum , the bottom where the brush is vibrates to make a loud sound. I cleaned the brush and took the gray plate off. when replaced made louder.


I misunderstood the original suggestion to fix this issue. It was a misalignment on the beater bar. I fixed that and voila! Vacuum is perfect again. Thank you ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Belt How do you remove the bottom plate to replace the belt. I have the brush off but can't figure out how to get to the other end to loop the belt


You need to take the top cover off to get to motor shaft. Some had a couple of screws from the bottom, others had tabs, use a flat blade screwdriver to fit into the slots at the bottom edge of the top, pry out and up to pop the cover off. ... Hoover Commercial C1403 Bagged Upright Vacuum

How many screws are there on the electolux epic 2500 sr on the bottom plate to hold it on?


There should be 5 screws. ... Vacuums

Bottom plate latch needs to be replaced


... Sanyo Performax SC-U126 Vacuum

I have any easy-flo built-in vacuum. I recently had the bearings on the motor, top and bottom replaced. I put the vacuum back together and it mow has low suction power. There is plenty of suction on the side of the canister where the rigid tubing meets the canister body but little suction at the wall plates. Any ideas? Roger


There is either a blockage or a pipe is open somewhere. You should check the system at the wall valve without the hose to determine if the pipes are blocked or if perhaps the hose is plugged. If one of the wall valves is damaged or open, this will af ... Vacuums

Dyson DC07 is excessively difficult to push. The plate on the bottom was replaced & helped a little bit for a while.


You should probably consider fitting a new brush roll. The bristles gradually wear away, to the point where they no longer help to pull the machine over the carpet. A new brush with full-length bristles will almost certainly solve the problem. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Sanitaire Model S661 Type A, heavy duty commercial motor, 8840 watts. A large nail was accidentally vacuumed. There was immediate noise, and then it smelled like smoke. We can see after removing the bottom plate that the translucent plastic fan was completely broken. Can it be replaced? We have no repair service nearby.


... Eureka Sanitaire S661 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0495 seconds