Having problems with your Eureka Uno 2998AZ Bagless Upright Vacuum ?

Handle from my Eureka Uno 2999 AVZ broke off

\015 How can I get a replacement?\015

Answers :

Try a company called cds they r in the midlands but they courier parts out 2u dont have their no 2 hand u will need the model number try the web marting
Repair Help & Product Troubleshooting for Eureka Uno 2998AZ Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Handle from my Eureka Uno 2999 AVZ broke off


Try a company called cds they r in the midlands but they courier parts out 2u dont have their no 2 hand u will need the model number try the web marting ... Eureka Uno 2998AZ Bagless Upright Vacuum

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!


Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

My Eureka Optima vacuum handle broke right at the metal tube.


I have exactly the same problem. I plan to drill a hole in the handle through plastic and metal, and then pass a metal pin to hold them together. I don't rotate the handle much, so the loss of handle spin functionality will not be a major issue for m ... Eureka 431A Optima Bagless Upright Vacuum

The handle release pedal broke on my Eureka Smartvac. The spring is still in tact. I have a replacement pedal, but cannot figure out how to install it. Any suggestions?


... Eureka Smartvac 4870 Bagged Upright Vacuum

The handle for my Eureka 5893 AVZ was getting very hot. Finally, the wires around the switch melted and the vacuum will not work. What is wrong? Is the switch bad? Nothing else appears to be wrong.


Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. It almost melted the handle! Ordered a switch after talking\015\012to several repair men. Talked to Eureka, too, and they were absolutely\015\012no help. Cheap wiring ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

What type of belt does the Eureka Uno take? - Eureka Uno 2998AZ Bagless Upright Vacuum


Here is a link to the belts for the Eureka Uno models and a manual you can view which has instructions.Eureka Uno Belts and Manual ... Eureka Uno 2998AZ Bagless Upright Vacuum

I had a house fire and lost most of my belongings. But I had just purchased a Shark Steam mop 3501. Loved it. Well it did not get destroyed in the fire but someone managed to break the handle off. Just the handle itself was broke off the rest of the handle rod is ok. I'm trying to see if I can replace the handle and not the whole shaft. Can you help me.


Yes you can replace jus the handle, the replacement part for the handle is available at the manufacturer's web site in the Parts and Accesories section. Enter M/N: S3501 to confirm it's the same as on your unit.\015\012\015\012 ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Floppy handle When I depressed the pedel to lower the handle on our Savvy there was a snap and now the the handle won't stay up. I assume there is a spring or someting else that broke. I can't find an exploded view of the vacumm to to take it apart to find out whats broken. Any ideas on what it is.


You have to take the base cover off to find out what broke,there are some screws on the bottom remove those to take the bottom plate off then,then up inside there are more screws to on the top remove the emblem and take that screw out ,that should e ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

The power brush floor rug attachment on my Eureka 6997 A Oxygen Canister Vacuum goes on an off as I use it. I replaced the The power cord from the handle has 2 plug in connections: 1 at the handle / upper wand 1 at the lower wand top of the power brush attachment I replaced the entire wand assembly and it worked great for a year or so and now it's doing the same thing again. I was told to keep the power switch on the handle set to off when connecting the power brush attachment or it will bu


This is from the prongs not making a good connection causing an arch inside the plugg causing what looks like rust on the plugg. I would try snugging up the connection by squeezing the female section to get a better connection on the prongs when it i ... Vacuums

I broke the handle part of the shark steamer #53101. I don't have the book to try to tell you the parts I need. Can you send me a picture or a copy of the steamer. It is purple. The above number may not be the correct one. It is broken in the center part. It has a little small circular piece that joins the two pieces which are broken. The beginning of the handle at the bottom of the steamer and the next session which has the steam release. The top of the handle is okay . It the middle and bottom


Hi,Ann there are very few parts for these...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Assembly I am trying to assemble the eureka smart boss. The problem that I am having is that the handle is not completely fitting into the cleaner body. I can slide the handle into the handle supports but it doesn't seem to click together. There is a space at the top; it doesn't seem to be able to fit as closely as the bottom. Thanks, Lisa


It may not just slide into place, you may have to knocj it into place, then put the screws in to secure it. ... Vacuums

Handle broke handle of 2961avz somehow snapped in half. any ideas how to find a replacement handle?


Part # for the handle is 75765-3. You should be able to order thru a local service repair shop. ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.


Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

I need to replace the cord on an older Hoover upright, model S660, about 1986 vintage. The cord broke where it enters handle. Handle comes apart easily. Just not sure how to pop the switch out without breaking it. Was looking for a manual online to see parts diagram and/or instruction on disassembly and cant seem to find one for that old of vacuum.


Check ebay. those vacuums are worth fixing. I loved them. they would **** the carpet off of the floor! those cords aren't hard to replace.just remember the way you got the old one out. ... Vacuums

Eureka Model C2094-Type GW Vacuum 1 Bags-Belt- Beater Roller or bristles that go on roller-light bulb Vacuum 2 Bags-Belt-Beater Roller-Bulb-Plastic frame the motor bolts on-Metal holder the handle go in that lets the handle move up and down


... Eureka Vacuums

Eureka capture vacuum - Eureka 8802AVZ Capture Bagless Upright Vacuum, Telescopic Self Cleaning Duster, Power Paw Turbo With Riser Visor, Dual Powered Edge Kleener, Comfort-Gripped Oval Handle, HEPA Filtration, 15 Extra Wide Cleaning Path, 30 ft. Cord Length, UPC 023169120891 8802


... Eureka 8802AVZ Capture Bagless Upright Vacuum, Telescopic Self Cleaning Duster, Power Paw Turbo With Riser Visor, Dual Powered Edge Kleener, Comfort-Gripped Oval Handle, HEPA Filtration, 15 Extra Wide Cleaning Path, 30 ft. Cord Length, UPC 023169120891 88

Model number U5763900 Serial Number 090400013588 Handle broke off just above the four screws that attach it ti the boby of the vac. Hoover does not list parts for models that are more than two years old. The vac operates perfectly but without a handle my wife cannot use it, where can I find a part replacement. easy to remove four screws and replace. dont want to drive 100 or more miles to find a authorized repair shop. Oh yes, this is a Hoover Preferred Wind Tnnel Bagless


Get over it and buy a new one!!! ... Vacuums

I purchased a Eureka C4910 last year and have a question that I am hoping you can answer. There are two motor actions with this vacuum, 1) the vacuum suction, and 2) the beater bar. The action of the beater bar is that motor is supposed to automatically shut off when the handle is in the complete vertical position assuming the vacuum is stationary, but then turn on when the handle is tilted toward the floor, assuming the vacuum is moving back and forth. The beater bar motor turn-on mechan


Good day!Normally when the motor is easily moved back and forth means that it have a proper lubrication,proper alignment and no clogs.When the motor and the belt is OK the problem could be on electrical wiring and switch ... Eureka C4910 Bagged Upright Vacuum

Broken Grip on handle of the Eureka 421A EZ Kleen Bagless Stick Vac. Need to replace grip or complete handle.


... Eureka 421A EZ Kleen Bagless Stick Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

Handle broke and had to call in the duct tape. hate to trash the vac just for this reason (although i'd take almost any excuse to buy an oreck). is there any way to get a new "ergonomic handle"??? thanks


This site will probably help you:http://www.fixya.com/websearch.aspx?cx=partner-pub-8183356113384228%3A3nccpq-il5y&ie=UTF-8&cof=FORID%3A11&q=ergonomic+vacuum+handle&sa=Search#1392Jim ... Euro-Pro NV31 Infinity Vacuum

The handle on my h2o steam mop broke. Where can I find a new handle?


We have no resources to find parts, sorry if u didn't understand that, that said based on my experience you will not be able to buy parts for this, this type of product is considered "throw away" ... Vacuums

Replace handle release buttom Eureka 4870 - Eureka Smartvac 4870 Bagged Upright Vacuum


... Eureka Smartvac 4870 Bagged Upright Vacuum

Eureka 2999 dvz brush roll - Eureka Uno 2998AZ Bagless Upright Vacuum


... Eureka Uno 2998AZ Bagless Upright Vacuum

Eureka model 4716 type avz reset button - Eureka Vacuums


... Eureka Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0785 seconds