Having problems with your Eureka Uno 2998AZ Bagless Upright Vacuum ?

The motor that turns the rollbrush does not seem to be turning. How can i check to see if the motor is still working? the belt looks fine.

Answers :

Have u tried getting access to the motor 2 check that the spindle the belt goes onto is turning or has the belt strectched marting
Repair Help & Product Troubleshooting for Eureka Uno 2998AZ Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The motor that turns the rollbrush does not seem to be turning. How can i check to see if the motor is still working? the belt looks fine.

Have u tried getting access to the motor 2 check that the spindle the belt goes onto is turning or has the belt strectched marting ... Eureka Uno 2998AZ Bagless Upright Vacuum

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?

... Kenmore 34722 Grab-N-Go Upright Vacuum

My Bissell 3760-1 has stopped sucking in the roller portion. The grab n go part are working fine. Checked the belt and it looks fine. Did I burn up the motor or a microchip?

Hey Lisa! Sorry you're having difficulty with your Lift-Off vacuum. Here's a link to troubleshooting steps to assist you with the suction.\015\012http: ... Vacuums

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.

Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Bissell pet hair eraser model #3920. It's been working great until last night. I went to use it and the brush won't spin. It also smells like it's burning. I checked the belt and it looks fine, and the brush spins by hand easily. It's not clogged anywhere that I can see. Anyone have any other ideas? This vacuum is only 8 months old.

- Remove the access panel, which is on the bottom of the machine. There are 4 tabs to lift on the access panel to remove. Start with tab 1 then 2-4 tabs.- Check the brush, and belt for any damage. Clean off any debris on the brush. ... Bissell 3920 Bagless Upright Vacuum

Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th

... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John

It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag

... Euro-Pro EP621 Bagless Upright Vacuum

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced

There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum

I have a Necchi LYdia 3 machine type 544 The motor was overheating and I removed the bottom cover and examined the motor .It looked fine and ran well. It worked OK for a time and then got hot.I was able to partially remove the motor for inspection.I found that the cooling impeller was not secured to the shaft,I tightened the set screws and reinstalled the motor. In process of getting the drive belt back on I turned the wheel that extends out of the case to index the screw that attaches the bobb

Good day!Please try to re align the motor position.You have to do is repeat the procedure that you take to remove the motor and double check the alignment because all motor in misalignment is very hard to turn.And ... Vacuums

Beater bar my beater bar won't go around, checked & the belt is fine. The motor driving the belt isn't working

... Hoover Platinum LiNX Cordless Stick Vacuum

My bissell 6590 works fine with hose attachment. Motor shaft turns when belt and roller are off. When belt and roller are on it's noisy and smelly. Now one end of the roller actually melted in the holding slot. Do these rollers wear out like this or should I be looking for another problem.

Replace the roller,belt and before instalation clean motor shaft where belt rolls. you can turn on the vacumm and using a knife scrape the motor shaft from the black dirt. ... Bissell 6590 CleanView Bagless Upright Vacuum

WST 1600A I purchased this vaccum about four months ago from Heartland America. Up to this point it's worked fine. After cleaning it this time when I went to start vaccuming again it runa for about 10 seconds and cuts off. I've changed the battery, taken everything that can be removed out checked it and replaced it. THe motor sounds like it's straining. I have not taken the housing off the motor to see what's going on with that. I misplaced my manual.

It sounds like there is a clog. If there is no air flow it could be overheating. ... Westinghouse WST1600 Upright Vacuum

Bad smell after using my windtunnel for a couple of minutes i noticed an odd smell. i turned it over and checked, the belts are fine but i cleaned out the hair anyway. after doing that the self propel seems to struggle and it is hard to push. when i look through the window on the top i can see the brush spinning freely but then when i push it, it slows down dramatically and then picks up again. the suction is fine. what do you recommend?

It may be the roller bearings? ... Hoover U5450-900 Windtunnel Supreme Bagged Upright Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

When i turn on my yellow Eureka upright everything works but when i flip the switch on the handal to do the carpet the brushed do not work. The belt looks fine. Is the motor dead?

The brush is worn out most likely ... Vacuums

I lent it out (NEVER AGAIN!) got it back and no water squirts out of it in front I looked at it with the cover off but it doesn't come all the way off anyhow nothing looks clogged the belt is all fine too. Clean all the grime is seen and still doesnt work. What's wrong?

It might be pet hair caught in its hose. You might have to disassemble everything just to be sure. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.

Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

Filter queen 95X (1991) Motor is noisy but still work fine. Can there be a loose screw inside ? Can I open the motor and look inside ?

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=766802\015\012Generic problem for all Vacuums\015\012Filter queen 95X (1991) \015\012Posted by alexun o ... Vacuums

Stopped working Was working fine then it smelled like burning rubber, not the belt I checked. It sounds like the motor wants to run then it just stopped but the light is on. What do you think, go by a new one?? This has been a great vacuum cleaner and I can not seem to find a Sharp anywere. Thanks for your time.

Well it could be the motor, if it is it would cost around $80 or so for a motor. May be better to buy new, thre are a number of good brands out there. ... Sharp Twin Energy EC-12TWT4 Bagged Upright Vacuum

Changing fan I changed the broken fan in my eureka 1934A. Put the cover back on and reattached the belt and when I went to start it, it wouldn't work. I took the cover back off to see what was going on and it looked like the motor was running in reverse of what it had been. Is this possible?

My solution is one that only works if the vacuum is a spare... To get mad at it and throw it in the garbage... \015\012\015\012My thought though on what the problem actually was... Seeing as where the vacuum came from and what the problem ... Eureka 1934 Bagged Upright Vacuum

The bar isn't turning on my dyson..the belt is still fine looks like maybe something with the motor?

The DC07 has a "brush control system" operated by a knob on the right side of the base. This knob has two positions: "bare floors" (or "off") and "carpet" (or "auto"). The roller will turn only when the knob is on "carpet", and even then only w ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1498 seconds