Having problems with your Eureka Uno 2998AZ Bagless Upright Vacuum ?

My eureka bagless uno vac problem is when I use it the belt gets really hot and starts smoking


Answers :

Try to manually turn the brushroll. if it feels tight then u will need a new brushroll. otherwise try replacing the belt
Repair Help & Product Troubleshooting for Eureka Uno 2998AZ Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My eureka bagless uno vac problem is when I use it the belt gets really hot and starts smoking


Try to manually turn the brushroll. if it feels tight then u will need a new brushroll. otherwise try replacing the belt ... Eureka Uno 2998AZ Bagless Upright Vacuum

Over heating? My 10 gallon 4HP shop vac has started shutting off after about 30 sec. after I turn it on to use. It smells real hot after I shut it off. I have changed the filter and the bag, which did not solve the problem. Any suggestions on what the problem could be? It's only about 31/2 years old and I really don't use it all that much, mainly for getting up dust and cob-webs from my garage.


It sounds like you need to replace the motor in it . thank you for using fixya ... Shop Vac ShopVac 3 HP 2 Stage 10 Gallon--Automotive Wet/Dry Vacuum Vacuum

Belts breaking/melting The original belt broke at almost 1 year so I replaced it. I changed the carpet setting to shag even though my carpet is very low pile to make it easier on the vacuum. I didn't get to use it but just a couple minutes and could already start smelling the new belt getting hot. I checked the roller and it is easy to spin. Not clogged with hair or dirt. Now the inside of the new belt has small pieces of rolled rubber instead of being smooth. The metal shaft that goes into the


... Dirt Devil M088905 Vision Bagless Upright Vacuum

Belt and lifter getting hot right away on start up.


Hello,\015\012I would say that it is definitely running backwards. I have a guide to replacing the power switch that outlines the reassembly of the Kirby and tells you which carbon brush wire plugs into which hole on the power switch. Ea ... Kirby Ultimate G Bagged Upright Vacuum

Help!!!! i have an older model of the dirt devil bagless quick vac. and it has been working great, just last week i was vaccuming my bedroom and i accidentally sucked up a string belt that goes with one of my capris. and today i emtpied out the dirt cup but it seems the the string belt that was sucked up is not within my reach and whenever i start the vaccum i get this distinctive noise that i've never heard before. help.


It's likely wrapped around the brush\015\012pull out the roller and un tangle it ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

My Oreck xl makes really loud sound and starts to smell hot when running still picks up but I am afraid I will damage something if I use it. The loud sounds gets very loud then quits for a few seconds then starts again.


... Oreck XL Ultra Bagged Upright Vacuum

Smoking belt Hey I have a Eureka 2961 avz bagless vacuum, and if it's on for a few minutes i can smell the belt burning.  If the vacuum is left on any longer the belt starts smoking.  I took the case off and there was a little debris but not much.  Is there a cause and fix or just time to replace the belt?


Belt is slipping because the bearings on the beater brushes, which it turns, are jammed or full of dust. \015\012Alternatively the belt has stretched after being overheated and needs replacing because it now slips. ... Eureka 2961AVZ Bagless Upright Vacuum

Belt problem My belt broke. I put a new belt in, followed the instructions, seemed to be right but as I started using the vaccuum, it starting smelling like burnt rubber. The belt was extremely hot. Took it apart, tried again and the same thing happened. Please help me!!!!


Get the old lady to use a dustpan and brush instead SORTED ... Kirby Generation 3 Bagged Upright Vacuum

Eureka 2981bvz bagless belt pully is getting too hot and burning through belt


Check the brush roll, if one end has overheated and is locked up so it won't turn, then you need to replace the brush roll. ... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

I've got a Kenmore canister vacuum, Progressive 236123, and there's a burning smell from the belt side of the head--smells a lot like hot rubber. I've cleaned the agitator and changed the belt, but I still get the smell. It's stronger when I'm using "carpet" mode than when I'm using "bare floor" mode. Any ideas what the problem is?


... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.


I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

I just used my Bissell Proheat, when I heard the vacuum sound get lower and lower then suddenly something "gave" and it got very loud and started emitting a burnt rubber smell. It still worked to put liquid into the carpet; seemed to have trouble getting it out. I checked the tank, filters, belt, and roller and all seemed OK - but when I started up again and looked down I saw sparks in the motor/belt area and shut it down immediately. Any thoughts?


The bearing that is located at the top of the vacuum motor has failed . Because of that the shaft of the motor's rotor is out of position and the pulley attached to it has started rubbing on the other pulleys, giving you that smell. the spark appear ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Vacuum started smoking and smelled. Yikes! I new it was the belt. Got a new belt replaced it.... with less than a minute it burned up another. The rotor/ pin that the belt goes around that should be spinning right? What do i do to get it to spin?


... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

My brand-new Hoover Windtunnel T-Series Pet Rewind Bagless vac simply shut off while I was using it and now I can't get it to turn back on. I've emptied the dirt collection bin and let the unit sit unplugged for 30 minutes to reset the Thermal Protector as per the manual. I've even tried a few different outlets just in case a fuse got tripped, but the vac still won't turn on. What happened? Do I need to return this vac to the store? I just bought it 5 hours ago.


... Hoover Vacuums

I have an upright, but use it as a canister. It will start sometimes and vac for about half and hour and then it will quit. I can't get it started again even after it cools off.


First check the hose and down by the brush roll for a clog. If there is a clog, it will cause the motor to overheat and the theremo protector will cause the motor to shut off until it has cooled. Now if it won't turn back on, the thermo protector m ... Electrolux Vacuums

My dyson has started to give off an acrid smell when I use it. I have checked all areas for blockages, cleaned the removable filter and removed all hair from the brush but this has not helped. I am worried the motor is getting hot in use. Whats the best thing to do next? Thanks


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

A friend who bought a multimaster less than a year ago has had his start a loud 'clattering', dry, noise, and the gearbox started to get hot. The output shaft now has about the same amount of slop as the total movement should be. It is one of the quick attach type. I bought one of the allen key attach type, and have found in the past with various 'name brand' tools, drills, angle grinders etc that they usually use a 'dry' type grease which soon throws off the necessary parts and they run dry u


Fein is an excellent tool and has an excellent warranty that will be void the moment you open the gearbox. I do not recommend this action. Fein is quick and responsive, especially for a less than one year issue.\015\012Farmerbear at FixYa.com ... Fein Multimaster Rs - Msxe 636 - 2 Rs

We replaced the belt after about 5 uses, and now every once in a while it smells like burning rubber, I checked to belt to make sure it was ok, and then last week it started smoking. Is there reported problems with this model?


If the belt is hot or burning during use, it could be due to a beater brush, which the belt drives, being bound up in some manner.\015\012The beater brush is removed during belt changes and should be cleaned of all debris as best you can.\015\012At e ... Dirt Devil Reaction Twin Cyclone Upright Vacuum

Burned out The best way for me to describe the problem is to post reviews I made on Amazon.com, which is where I purchased them. ________________ Based on my past experience, I bought another 6 months ago. I live in a very tiny 2 room apartment and do not vacuum lots of dirt. I noticed this new vac getting very hot to the touch where the motor is located with only a few minutes of use. Today it just STOPPED. When I felt the canister, it was HOT. It obviously has burned out. Upon closer inspect


... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

Hoover self-propelled windtunnel U6430-900 flat belt gets hot & becomes hard to push. It has a filter bag. Purchased 8/2/01. Took one plate off bottom. Used a compressor to blow out dirt & dust. Put new thin belt on.


Belts get hot when fibers from carpet get wound arounf the belts mounting shaft. Best to take a razor and cut off any fibers so the belt doesn't get hot again ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

I have a Miele S1721 Powerhouse upright vacuum. When the belt broke I took it into the shop (because when i tried to replace the belt, the tension was so tight I couldn't get it back together!!). When I got it home I DISCOVERED THAT THE HEIGHT ADJUSTMENT DIDN'T WORK anymore. It seems like it's set really hight, because it no longer contacts and brushes the carpet. So it's now useless. I went back to the shop and the tech denied that there was anything wrong. (I didn't have the vac with me). No


Hi\015\012The Miele uprights (S170 and upwards) with the Powerhouse title are ALL Panasonic uprights which have been at one time sold in the UK. Therefore the upright may use TWO drive belts which need to be looked at: Take off the sole plate a ... Vacuums

I used one tank of water/solution and the spot bot worked great. i refilled it and tryed to use it again, but all of the lights came on and it started beeping. why is this? is it getting too hot?


My machine is not spraying water. What can I do ... Bissell SpotBot Robotic Wet/Dry Vacuum

Burning smell While using the vacuum, the running light will get dim. If I hold the handle at the point where the light gets dim the motor will start smoking. I can either raise or lower the handle and the light will brighten up and the vacuum will run fine. Any ideas???


Hi theres two things that could have made it start doing that 1 the whires have a short in it or 2 the motor has gon faulty. you might want to buy a new machine ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Have a Centralux Aerus about 5 years old. Don't see a model number. There is suction but beater brush quit working. Was using for a few minutes, shut it off for a few minutes, turned it back on and suction only. Tried the reset button also. Tried the sidekick attachment and it works fine. There was no smell like something was hot. Belt is fine. Are there any fuses or anything else to try? This vacuum cleaner has not really been used that much, it is hard to believe the motor would need replaced


There probably is a loose wire in the handle near the switch or a wire off near the swivel elbow near the vac power head. With the right fastener tool to remove some screws you can fix it yourself ... Electrolux Centralux Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1542 seconds