Having problems with your Eureka Uno 2998AZ Bagless Upright Vacuum ?

How to put on a belt on eureka uno bagless vacuum cleaner

\015 How do i take the cover off to replace the belt\015

Answers :

Unplug the vacuum.

Turn it over so you have access to the bottom of the unit (you should see the brushroll)

At the base where the "head" attaches to the body there is a small silver button that you must depress to remove it from the body. Press the button in with a screwdriver or unsharpened pencil while pulling the "head" away from the body.

Use a #2 Philips screwdriver to remove all the large screws from the bottom. They are all the same size and type so you can collect them for safekeeping without worrying about which one goes where. There are 2 smaller screws (if I remember correctly) that are for the upright lock that you do not need to remove. They will be on the small plastic piece near where the bottom brush "head" attaches to the vacuum.

Remove the clear plastic clog cover.

Gently pry the gray cover off. This shouldn't be too difficult as the cover goes loose when you remove the screws.

Flip the gray side over and you should see the innards including the brushroll, the motor, wiring, etc. Facing the assembly like you were looking head-on at the vacuum the belt should be on the right.

Pull up the far end (non-belted end) of the brushroll and then the belted end.

The brushroll should now be free and you should check the teeth on the belted end of the brushroll to ensure none are broken.

Remove the old belt from the motor (also toothed) and replace with new belt (a second spare would be handy to keep around and this is a good opportunity to clean up the air path).

Put toothed end of belt into the belt loop and stretch it a bit to get the toothed end back into place. The belt should auto adjust but just in case you may want to manually rotate the brushroll a few times after replacing the far end (non-toothed end)

Repeat the rest of it in reverse order to put it back.

Good luck!
Here is a link to replacement Eureka Uno belts and to the Eureka Uno manual which has instructions and pictures on how to change the belt:

Eureka Uno Manual and Belts
Repair Help & Product Troubleshooting for Eureka Uno 2998AZ Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to put on a belt on eureka uno bagless vacuum cleaner

Unplug the vacuum.Turn it over so you have access to the bottom of the unit (you should see the brushroll)At the base where the "head" attaches to the body there is a small silver button that you must depress to remove it from ... Eureka Uno 2998AZ Bagless Upright Vacuum

Is there a diagram/picture to help me visualize how to put cleaner belt back in vacuum? I was taking base of vacuum apart so I could get rid of hair that were wrapped on the roller. The cleaner belt came to loose and I could not figure how to fix it back. the model is eureka upright bagless series 430

Hi,Sorry to hear your belt fell out. Not good if you've never replaced a belt before...Here is a website where you can read a detailed description of how to change a belt: http://www.ehow.com/how_8034505_eureka-belt-replacemen ... Eureka 431A Optima Bagless Upright Vacuum

The belt on my vacuum cleaner model 6596 bissel powerforce bagless turbo keeps breaking. As soon as I put on a new belt and start it up the belt snaps. It is the durabelt meant for this vacuum model. Also, my son has been having the same problem with his. He has the same model and same belt. This problem is occurring even after a thourough cleaning.

I would guess you aren't centering the belt correctly, thus it's edge is caught between the brush and another solid object, causing the breakage.\015\012When you get the belt on the the brush and the brush back in place, turn the brush a few ti ... Bissell 6596 Bagless Upright Vacuum

What type of belt does the Eureka Uno take? - Eureka Uno 2998AZ Bagless Upright Vacuum

Here is a link to the belts for the Eureka Uno models and a manual you can view which has instructions.Eureka Uno Belts and Manual ... Eureka Uno 2998AZ Bagless Upright Vacuum

Hey i have a eureka 2971 BVZ upright vacuum cleaner and after removing the old belt to replace it. I accidently removed the Guard Belt and i can't remember how to put it back on.

... Eureka 2961AVZ Bagless Upright Vacuum

How do you change the belt in a Eureka Bagless The Boss Power Plus vacuum cleaner

... Eureka 4700A Maxima Bagless Upright Vacuum

How do you put a belt on a eureka 2 stage whirlwind cyclonic vacuum cleaner

... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o

I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

Smoking belt Hey I have a Eureka 2961 avz bagless vacuum, and if it's on for a few minutes i can smell the belt burning.  If the vacuum is left on any longer the belt starts smoking.  I took the case off and there was a little debris but not much.  Is there a cause and fix or just time to replace the belt?

Belt is slipping because the bearings on the beater brushes, which it turns, are jammed or full of dust. \015\012Alternatively the belt has stretched after being overheated and needs replacing because it now slips. ... Eureka 2961AVZ Bagless Upright Vacuum

New Eureka vacuum cleaner belt keeps slipping off

You may have a bad brush roll, part #61250-1, or the base itself has a problem and isn't letting the brush roll sit straight so it can be in alignment. ... Vacuums

I have the Bissell upright cleanview bagless vacuum cleaner. My belt broke and someone else took it off. I bought a new belt but do not know where it goes on the cleaner. Please help

Easy to do. Unplug the vac. Turn the vacuum over and look for three finger latches on the bottom behind the brushes. Unlatch these and pull the faceplate off. Then, grab one side of the brush and pull straight up (they just sit in grooves on the ... Bissell CleanView 3596 Bagless Upright Vacuum

How to change a belt on eureka vacuum 4903 f - Eureka Power Plus 4703D Bagless Upright Vacuum

... Eureka Power Plus 4703D Bagless Upright Vacuum

I have a Zanussi 1700W bagless upright vacuum cleaner which keeps cutting out after about 5/10 mins use. I had to replace the rubber drive belt which snapped not long after purchasing and it was fine for a while, but now its just keeps cutting out after a small amount of use. Nothing wrong with belt which is still intact so we don't know what the problem is. It's a great cleaner otherwise - but it's driving us mad!! Please help!

... Vacuums

Have eureka 9734 replaced belt, put back together,brush rotates well but vacuum is not picking up anything, no suction.

It sounds like the machine is clogged. Check the port behind the belt and any and all hoses for obstructions and remove. ... Vacuums

We have a Hoover upright vacuum cleaner, model Core 7. There is a switch that turns on and off the brush drive. This operates via a cam with a bearing putting pressure on the final drive belt to engage the brush head. My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt. There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a

Yes, there should have been a white plastic sprocket on top of the bearing - in its channel the belt would sit. Unfortunately no parts are available for this unit that can be bought retail - only available by order to dealer repair shops.\012\012\012 ... Hoover Vacuums

Trying to replace belt on hoover convertible bagless upright u8188900. belt replace # 38528-049. i have opened vacuum and put belt back on, but it will not get tight enough around the motor gear and the brush spool to be able to activate. am i missing something? mike

... Hoover Vacuums

My Eureka Maxima isn't working right. The belt is spinning fine until I lower the handle to start to vacuum and then the belt stops spinning. As soon as I put the handle back in the upright position the belt spins again.

Sounds like belt is worn try changing belt. ... Eureka 4700A Maxima Bagless Upright Vacuum

I have a Eureka Altima vacuum cleaner that doesn't pick up very well. The suction seems fine but the brush roller doesn't seem to pick up from the top of the carpet. When you lower the height of the vacuum the belt rubs and smells horribly. How can I get the vacuum to pick up better?

That means that you need to replace the belt. Here is the belt you need to replace and the manual which has instructions:Eureka Altima ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

What belt is used for a Eureka upright Model 2025B vacuum cleaner? What is the diameter (or the circumfrence)? of the round belt

... Eureka Electrolux EL5020A Intensity Upright Vacuum Cleaner


... Eureka 5849A Boss Bagless Upright Cyclonic Vacuum

Does a Eureka Optima bagless upright vacuum have a belt in it? Mine stopped working and then now the motor sounds strange. I cannot find a belt.

... Eureka 431A Optima Bagless Upright Vacuum

How to change belt on eureka capture - Eureka 2971AV EZ Kleen Bagless Upright Vacuum

... Eureka 2971AV EZ Kleen Bagless Upright Vacuum

How do I change the belt on Eureka Pet Pal - Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Unlike most vacuums, this one the screws are on the top of your base. There are two screws one on each side. When looking at the front of the vacuum right side screw is located above the s in 12amps and on the left side screw is located above the p i ... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

I have a eureka surface max 300, i saw smoke come out of my vacuum i seen that the belt was broke every time i change belt i run it on it snaps every time ive put 3 new ones and each one break right when i start it it looks like the metal piece is burning it is there a piece missing?? what am i doing wrong?? ugh i just purchased it couple of months agoo not even older then 6 months .. what do i do?

... Eureka Capture Upright Vacuum Vacuum

Have a Morphy Richards 1500 watt cyclone Ultra Light vacuum cleaner Model No. 73320. Belt has broken and I have lot the manual. Need instructions as to how to put in a new belt

... Morphy Richards Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1243 seconds