Having problems with your Eureka upright vacuum Cleaner 7700 Series ?

The motor overheats when using

The motor overheats and smells hot after 5 minutes.

Answers :

Repair Help & Product Troubleshooting for Eureka upright vacuum Cleaner 7700 Series

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The motor seems to overheat and smell a bit like burning.runs noisily too.this only seems to have happened since I used the small turbo brush for the first time ever on the stairs.


Check that there is no build up of fluff or debris in the machine. If the motor is getting hot its cos its not getting enough air ... through obstruction... probably you have something like a screw etc thats touching moving parts and restricting flo ... Miele Vacuums

The motor overheats and shuts off. This annoying because it has done it at least 5 times today during normal vacuuming. It shuts off easily when you use the hose and canister to clean the steps or around the floor. What can I do to alleviate this problem?


Almost all vacuum cleaners have a thermal cut-out, which operates when the machine gets too hot and resets automatically when it cools down. Overheating is almost always caused by a blockage. Either the filters need cleaning or changing, or the ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

Dyson DC07 motor overheats


The motor brushes are worn down and can be expensive to get someone to fit them for you so i think its time for a new cleaner ... Dyson DC07 Allergy Blue/Turquoise Bagless Upright Cyclonic Vacuum

Fantom vpw46h,house pressure washer.the motor runs,it was setting for sometime started,using it,but never had any pressure besides the house hose pressure, with the motor running,then the pressure startes to work great,while using it the wand hose came out of the pressure washer,i put it back in,now the motor will only run when i try to adjust the wand head but will not produce any pressure and will shut the motor off,it seem like as soon as the wand hose came out of the presure washer and after


... Vacuums

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?


... Kenmore 34722 Grab-N-Go Upright Vacuum

On my Kenmore whispertone 5.1 the bearings are bad on the motor there are two bearings they are listed as 608 BRS I see bearings all over ebay 6082RS 608SS but none BRS can I use any 608 Bearing or does it have to be a 608 BRS Bearing are these dry bearings or greased bearings I cant get any real information on the bearings I dont want to go to sears when I can get bearing much cheaper off ebay can some one shed some light on the bearings I would use the motor is made by Lamb Ametek went to ther


... Kenmore Vacuums

Motor dying? recently my herritage has been sounding sick, i tried to use it the other morning and it barely could blow up the bag, there is also a hot smell to it when it is running, the motor doesnt sound as powerful as it use to. Any suggestions?


Replace the carbon brushes in the motor. ... Kirby Heritage II Vacuum

Motor My vacuum cut out as I was using it. After some experimenting I found that the circuit reset had gone off. When I tried a second time while near the motor , there was a flash and again the motor shut off. At this time I am guessing that the motor is faulty. The central vacuuming is approximately 12 years old.


If it tripped the reset again, I would probably agree with you. Check out centralvacuum.com for another motor. They aren't the cheapest, but they have excellent support. Good Luck!! ... Easy Flo EF1400 Central System Vacuum

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti


You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

Electrolux Centralux I have a Electrolux Centralux. When I plug the hose in at one of the wall outlets the motor will not start. If I go to the motor and slap the unit it will start.....then...it will not stop unless I unplug the power cord to the motor. If I plug the power cord back in, the unit will not restart until I slap the motor unit again. The unit has only been used 20 - 30 times. Any suggestions?? Thanks, Bruce


I dont know if you had your unit looked at yet but it sounds like the Power module is going. I repair the machines so I know some of the work. ... Electrolux Centralux Vacuum

Hoover Jet and Wash 1500w S6254 001. Used once with great difficulty as assembly and use instructions are hard to follow.Now will not work as carpet shampooer at all, although assembly is correct as far as I can see and both motor and pump appear to be working and I am using the recommended cleaning fluid.Hoover website is no use at all in solving the problem.No cleaning fluid is being drawn up from the tank in to the cleaning fluid hose.There is suction from the suction hose so the problem appe


I am having the same prob my uncle got me one i cant find the manual anywhere to set it up the prob i have is where does the handle to make the water go out connect tooo ??? on the main pipe that sucks it back up i have tried every which way but not ... Vacuums

I was just using my Bosch 1450W bagged vacuum and all of a sudden, the motor just shut down. No warning, no problems. The light still turns on, but the motor is unresponsive. There is a clean bag and filter, and nothing caught in the front roller. The motor sounded fine - no shaking, or weird frequency variations. There were no weird smells, just a little bit of heat, but nothing beyond normal. I've had this thing for several years, and never had a bit of trouble with it. Any suggestions


Many vacuums have internal thermal switches that need to cool to allow the vac to operate. After 30 minutes, check all 3 air filters and try again.\012Gary ... Bosch BSG71310UC Bagged Canister Vacuum

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?


... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

The pump motor in my Bissel Proheat 2x Plus seems to have failed. It was seized so I sprayed WD-40 in it and let it sit for 3 days. Now I can turn it by hand, but when plugged into the unit it still doesn't spin. Here's a picture: http://bbay.dreamhost.com/bissel_proheat_2x_plus/P1070021.JPG I wanted to take the motor out and hook it into another power source to see if I can get it going but it has 3 wires. I'm used to only 2 (+ and -). How can I hook the motor up to another power source,


... Bissell Vacuums

Recently my central vac system started making a louder than usual and laboured sound when in uise, enough so that I took note and inspected the canister and motor while running. The motor was trowing off blue sparks and looked like it could 'POP' at any moment. I will not risk using it until I know what the problem is and how to repair it. My assumption is the motor needs to be replaced. The system came with the resale house I bought 3 yrs ago but I do not know the age of the system itself.


... Vacuums

Dyson DC07 Vacume cleaner trips on thermal after 10 min motor not excesive hot resets after 15 min has been doing this for the last 3 mths. Could it be faulty thermal or motor overheat how can I check without changing motor


First, check both filters on that unit. the premotor filter on the side, and the hepa filter underneath the canister. if those filters are clean move through the suction channel and look for a clog or obstruction. also make sure the canister is clean ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have an Electrolux LITE upright carpet cleaner - about 15 years old. Suddenly last night when using it, from the normal motor (whooshing) sound, the motor suddenly went very slow and with a slight grinding sound. The brushes are now just turning round very slowly and areobviously not picking up anything. Has the motor gone or is this repairable, or should I just get a new cleaner? I have tried to open the machine from the bottom to see if anything is obviously wrong, but it looks complicated a


... Electrolux Vacuums

My 20" Patton electric fan has stopped working. I use it for animal cooling and it operates in dusty conditions. I suspect that the motor is shot. Is it worthwhile to replace the motor and are motors even available?


You could just try to clean the motor out by taking it apart, and shining the shaft up. then put some motor oil/engine oil on the shaft. That will work 99% of the time. ... Vacuums

I have a Eureka Maxima, this was a gift to me, but I have to say it is the worst vacuum I have ever used. Not only do I have a problem with the suction and the filter getting clogged, but it overheats - it takes me all day to vacuum my house, because the darn thing overheats after every room. Besides for tossing it off a cliff and buying a better vacuum, what can I do?


Get yourself a dyson ... Eureka Vacuums

I have a fantom fm741h and the motor overheats. Do I have to replace the motor or is it fixable


... Fantom Vacums FM741 Twister Bagless Upright Vacuum

After using the vac for 10 minutes or so, the motor starts turning on and off with greater frequency the longer I let it run. Eventually it is on and off so frequently that it has no power. Would this possibly be the 24V relay? I have checked the breaker on the unit and it is not tripped. Does the motor have a thermal overload switch separate from the breaker?


No it dosen't. I fix central vacs all the time and relays usally don't do what you described. They either go out all the way and won't turn on or they will trip and you will have to push the breaker back in. What is probably happening is you have a s ... Electrolux Centralux Vacuum

Old Sanyo 1500 watt "Power Control" vacuum cleaner. I need to remove the plastic covers that are attached to the on/off switch and the power cord recoil. This will allow me to remove the retaining screws for the upper motor cowling. The motor and wiring is clogged with wood dust and I want to blow the dust out using compressed air.


... Sanyo Vacuums

Borrowed Brother XR7700 Sewing Machine 1st: Sewed one inch OK; moved fabric and it stopped sewing, motor made thudding noise. When push-button (NOT pedal) is used, gives error E6, consistent with motor noise. 2d: In order to check threading had to manually PULL bobbin case toward me or it was UNDER needle plate. Cleaned a fair amount of dust out. Reinstalled bobbin, etc., per manual, rethreaded. 3rd: Will sew 2-3 stitches, then packs up again just like in 1st instance above. Have st


Have you checked your needle. it could probably be bent somehow. you should replace it first because that also can confuse the sensor causing that error.regards ... Vacuums

Hoover F6212-900 My dear wife thought our 2 year old steam cleaner was a vaccum cleaner and used it with no fluid, I used it yesterday, it didn,t seem to clean the carpet and no water went into the dirty water tank it stayed dry. motor sounded ok Am I in big trouble Thanks for any help you can offer P.S. I still love her Alan from Canada


Press the handle release kick-button with your foot, extend the handle all of the way back, and take a look at the gap between the base of the unit and the handle/reseviour assembly. You should see several black hoses attached to the base and running ... Hoover F6212-900 / F6215-900 SteamVac Agility Upright Vacuum

We replaced the motor and the overheat light stays on and the motor does not run. Any suggestions?


Sounds like a bad thermal switch to me. take it a vacuum shop they should be a able to rewire it for you. ... Electrolux Epic 6500 Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0413 seconds