Having problems with your Eureka Vacuums ?

Eureka 7622 I am looking for the attactments for the Eureka Rally 7622.

Answers :

Repair Help & Product Troubleshooting for Eureka Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka 7622 I am looking for the attactments for the Eureka Rally 7622.

... Eureka Vacuums

Eureka rally 2 won't turn on - Eureka Rally 2 Canister Vacuum with Automatic Cord Rewind, 980A

... Eureka Rally 2 Canister Vacuum with Automatic Cord Rewind, 980A

Eureka 2961AVZ Will not start ...I get a momentary flicker of power about every 3d or 4th time that I flick on the power sw. Outlet is fine / Plug looks good / chord looks good / I see no obstructions ........Would appreciate any helpful thoughts ....Trying to get Mom's Eureka 2961avz back up and running. Thanks

CAREFUL! This is how my problems started. The cheap switches (and wiring) Eureka is using in some models, especially my model) should provoke a lawsuit imo.Here's my story, just in case it might help. Mine started with a problem very similar ... Eureka 2961AVZ Bagless Upright Vacuum

Whirlwind 4481b i have the eureka whirlwind bagless model 4481b which looks the same as the 4496.i'm looking for the cover right above the dirt cup.it says eureka on it its just a cosmetic item serves no purpose but i need one can you find it or do you have it?

... Eureka Whirlwind 4496 Bagless Upright Cyclonic Vacuum

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the

Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

Eureka Rally 3977B vacuum cleaner rear wheel assembly

... Eureka 6983 Bagged Canister Vacuum

Looking for Eureka belt 70646A for a Eureka The Boss upright

I just replaced the belt on my Eureka The Boss Smart Vac (Model 4870D). I purchased a namebrand Eureka R belt from a local vendor. I did my best to follow the instructions printed on the bottom of the machine. I turned on the vacuum cleaner and the ... Vacuums

My eureka Hello im not sure what kinda of eureka it is a friend gave it to us...and I went to change the bag and vacuum and the spinner isnt going...and i dont think its the belt...help please! i looked on the back and it gave me a modle number its 4475

The belt may look ok, but am sure it is stretched and when this happens, the brush roll won't turn like it should. Did you check the brush roll ends to see if they turn freely, if not replace it. ... Vacuums

Looking to replace my eureka Boss central vacuum, but need a new unit with both exhaust and suction connections on same side. I was looking to replace it with an Imperium CV7700.

I would recommend the AirVac AVR7500 model. It's a great unit. ... Eureka CV1801 Bagged Vacuum

I am looking for a pulley replacement for a Eureka Lightweight Upright, 400 Series. I can't seem to find any on the internet with my searches, and Eureka doesn't seem to have anything on their web site either.

Call all-type vacuum and janitorial supply 314-275-8006 ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

How to replace filter in eureka rally II?

... Eureka Vacuums

Looking for Eureka Boss Belt

Go to abcvacuum.com They should have what you are looking for. ... Vacuums

I have a Eureka Central Vac CV1601b. The motor does not stop unless the Unit is unplug from the electrical outlet. Any Idea?.I removed the control unit to check if there was disconnected wires or burnt wires. Everything look normal. The circuit board does not show area that overheated. There seem to be 2 relays. Likely one of the two went bad. What do you think.

If the unit is relay controlled, there is always the possibility that when the unit was turned on, the relay contacts welded themselves shut making the power button ineffective. \015\012\015\012If you're familiar with relay pinouts, with ... Vacuums

I have a eureka surface max 300, i saw smoke come out of my vacuum i seen that the belt was broke every time i change belt i run it on it snaps every time ive put 3 new ones and each one break right when i start it it looks like the metal piece is burning it is there a piece missing?? what am i doing wrong?? ugh i just purchased it couple of months agoo not even older then 6 months .. what do i do?

... Eureka Capture Upright Vacuum Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o

I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

I'm looking for a eureka belt reference chart so I can find the belt I need.

Here is a link to a Eureka belt reference chart:Eureka Belt Reference Chart ... Vacuums

When i turn on my yellow Eureka upright everything works but when i flip the switch on the handal to do the carpet the brushed do not work. The belt looks fine. Is the motor dead?

The brush is worn out most likely ... Vacuums

Changing fan I changed the broken fan in my eureka 1934A. Put the cover back on and reattached the belt and when I went to start it, it wouldn't work. I took the cover back off to see what was going on and it looked like the motor was running in reverse of what it had been. Is this possible?

My solution is one that only works if the vacuum is a spare... To get mad at it and throw it in the garbage... \015\012\015\012My thought though on what the problem actually was... Seeing as where the vacuum came from and what the problem ... Eureka 1934 Bagged Upright Vacuum

Looking for the instruction manual for the Eureka Altima 2993AV HEPA Upright Bagless Vacuum Cleaner

Go to http://www.eureka.com/service/manuals/80244.pdf this is a direct link to the owners guide for your model or you can call customer service at 800-282-2 ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

I have an old (50s) GE vacuum canister model VIIVTI made in Bridgeport, and I don't know what kind of bag it uses. It looks like a Eureka, but it's definitely GE.

... GE Vacuums

Motor Fried? Eureka 431BX Vacuuming, and then all of the sudden the motor just stopped. Well idk if it's called the motor; the beater bar still spun, it was just the fan that stopped spinning Here is the whole vacuum in pieces http://i28.photobucket.com/albums/c237/SirFafner/Vacuum001.jpg Bottom Part, beater bar already taken out [Functions Fine] http://i28.photobucket.com/albums/c237/SirFafner/Vacuum002.jpg White Wire connecting to the fan motor [Looks black, i think it's fried, and that's the

Funny you said that,I went today and bought a bissel at Wal-Mart.Sure hope it lasts longer then the Eureka did.I will probably try to take the other one back to the store if I can find the receipt.Thanks so much. ... Eureka 431BX Bagless Upright Vacuum

I am looking for the filter for the Eureka bagless Altima vaccum cleaner

There should be an toll free # to call for eureka and they can direct you to the nearest authorized eureka service center in you area. If its a new model places like wallmart wont stock it. There are so many vacuum makes and models its impossible fo ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Help hi i have a eureka bravo model #9270 and i need instructions how to change the belt, i took out twoscrews it looks like the top comes off but it doesn't come off all the way.

The handle should be down and the top may have a tab on both sides to pry out with screwdriver. lay handle down and turn machine over. look closely around base between cover and there should be a tab to push on and cover comes off. ... Eureka Vacuums

Looking to replace vac belt on eureka altima bagless upright

Hi Jim\015\012You should find the cross head screws on top of the hood - look below the duster and there should be a screw there, also another screw on the other side and two either side of the main floor head.  ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Need to replace belt on Eureka Powerline 12.0 vac. Screws look like Torx head or something on bottom of vac. Are those the screws that need to come out for changing? If so, what size do I need?

No, do not remove the torx head screws for a belt change. If there are any screws that need to be removed for the belt change, they will be phillips head. What is model # of vac?? ... Eureka Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0404 seconds