Having problems with your Eureka Vacuums ?

I am assembling a Eureka Air Speed Bagless Model AS5203 and am unable to get the dustcup to snap into place...What am I doing wrong?

\015 Model AS5203\015

Answers :

Repair Help & Product Troubleshooting for Eureka Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am assembling a Eureka Air Speed Bagless Model AS5203 and am unable to get the dustcup to snap into place...What am I doing wrong?

... Eureka Vacuums

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!

Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Eureka 4467AV overheats and shuts down after about 3 or 4 minutes of operation. I pulled all the filters to assure no blocked air flow. I assume the motor is not getting enough cooling air but i can't figure out why. checked bag for blockages as well as hoses. could the thermal protection have gone bad?

... Eureka 4467AV Upright Vacuum

The handle for my Eureka 5893 AVZ was getting very hot. Finally, the wires around the switch melted and the vacuum will not work. What is wrong? Is the switch bad? Nothing else appears to be wrong.

Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. It almost melted the handle! Ordered a switch after talking\015\012to several repair men. Talked to Eureka, too, and they were absolutely\015\012no help. Cheap wiring ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Best place to get a eureka vacuum techical manual. my eureka lost power am unable to turn on.

Ofen it is the power switch is stuffed you may need to replace it... some vacums with foot switches to turn on and off get broken due to people standing on them to hard etc.... it bends the contacts in the switch... hope this helps ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?

... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

My eureka 4752A is like a leaf blower, it's pushing a lot of air through the vent blowing away all the dust. Why is it? Did I put it together wrong?

... Eureka 4752A Lightspeed Upright Vacuum Red

Have a Eureka Power Plus 12.0 Amps Model 4702 Type A 120 volts and 60 HZ that there is something wrong that it isn't picking up right and you can actually feel the air coming out of it near where the bagless canister attaches. My thoughts are that a seal is missing around where the hole lines up when the cannister is locked in. This Vac was my Mom's and she passed away and I think a part went missing maybe when it was taken apart to clean the filter and empty the canister. Need to figure out if

... Vacuums

I have the eureka boss 4495 widetrack and the end piece of the beater bar broke off. I guess I put it back together wrong when I put a new belt on. Where can I get a replacement part and will it work do you think.

Call the Eureka people (1-800-282-2886) and describe to them what the beater bar thingy that you broke is. Ask them if you can order that unit--if you think you can install it. Otherwise, ask them where to the authorized repair person closest to yo ... Eureka 4495A Bagless Upright Vacuum

I have a eureka surface max 300, i saw smoke come out of my vacuum i seen that the belt was broke every time i change belt i run it on it snaps every time ive put 3 new ones and each one break right when i start it it looks like the metal piece is burning it is there a piece missing?? what am i doing wrong?? ugh i just purchased it couple of months agoo not even older then 6 months .. what do i do?

... Eureka Capture Upright Vacuum Vacuum

Carpet attachment has two little holes just below where it snaps into place on the wand -- the airs going out those holes and not getting to the attachment so there's no suction

There is a small brush attachment that goes in there, you don't need it. Just tape up the holes. ... Kenmore Magic Blue 24195 Bagged Canister Vacuum

Belt?! hello, I need to change the Eureka Oxygen Canister Air Driven Upholstery Tool's Belt (model 5860Avh), but I don't know which one to get? any help please? Best, Pierre.

You will probably have to order it online. ... Vacuums

Suction Cover The suction cover of my Eureka Deep Steam 2575A is broken - the tabs snapped off of the cover so I am unable to screw the suction cover back on. I need to purchase a new suction cover but can't find one anywhere. Anyone know what I can do? thanks

The exact same thing happened to me. i just called and ordered it from eureka. the number is 1-800-282-2886. the cover cost 13.07 and the s ... Eureka 2576A Steam Vacuum

When I was putting my new rug shampooer together and the directions said to press the trigger and the clean surge button until I heard a snap, I did just that many times and never did hear a snap so I thought it had likely happened and I didn't hear it so I proceeded to fill the solution tank and get busy but no solution came out so I used the clean surge button instead and got the job done (I think). Can I continue to use it that way or is there a way I can get it to snap and use it the way it

My husband figured it out and it now works great! Thank you ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I have the Eureka Big Shot Envira Steamer. It get...

... Eureka Deluxe Enviro Steamer Vacuum

Eureka 2961AVZ Will not start ...I get a momentary flicker of power about every 3d or 4th time that I flick on the power sw. Outlet is fine / Plug looks good / chord looks good / I see no obstructions ........Would appreciate any helpful thoughts ....Trying to get Mom's Eureka 2961avz back up and running. Thanks

CAREFUL! This is how my problems started. The cheap switches (and wiring) Eureka is using in some models, especially my model) should provoke a lawsuit imo.Here's my story, just in case it might help. Mine started with a problem very similar ... Eureka 2961AVZ Bagless Upright Vacuum

I am trying to install a train air horn. i bought a viair compressor for it. the horns themselves have a 12 volt hookup going to what i believe is acting like a solenoid. when charged, you complete the circuit and walah, the horn blasts. the problem im having is when the compressor is building pressure, the air horn is automatically putting out a dull sound, getting louder as the pressure gets more and more. it sounds like its out of one horn however. it is doing that without the 12 v hookup. is

Hi! just a tip regarding the sound that comes up when building pressure. Is there a gasket or rubber seal on the horn? You may need to replace this for it may be worn. The air may be coming out of the worn seals resulting to sound even when not trigg ... Vacuums

Model # zw5000y8 The air conditioner is less than 2 years old, and has leaking water from the from of the air conditioner. I contacted Home Depot where I purchased the item and the only advice they could offer was that there was something wrong. I purchased two of the same air conditioner and I havent had any issues with the other. Can someone please offer any advice on the reason that the air conditioner is leaking from the front and filling up with water, not the normal condensation,

... Vacuums

How do I get my vacuum cleaner to blow air instead of **** air? I want to use it to blow up an air bed - Nilfisk King 240

... Nilfisk Vacuums

I have the eureka bagless capture. The main hose is what I am interested in. I cracked the end of the hose where I would attach other parts such as the slim attachment for corners and to get inside the pillows in my chair, The part that I broke is on the very end of the hose. I had the plastic part clogged with some hair and during the process of getting it cleaned out, the part that I am speaking about is broken. Can you help me. I thank you, Mo moss

Change the hose part try a company called cds they r in the midlands but they courier parts\015\012out 2u dont have their no 2 hand u will need the model number try the\015\012web marting ... Eureka Uno 2998AZ Bagless Upright Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

Wondering if the head is plugged up because it makes a sound like air is escaping somewhere. I've replaced the original cloth bag with a comparable "O" paper bag from Sears. I tried to see if there was a clog in the hose by placing a broom handle in the hose to see if something would loosen. I also cleaned the filter and the air filter. If the head is plugged, how can I fix it? We can't get the vacuum apart. Thanks.

I had this problem, but suction improved when the attachments were properly secured in their holders. ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?

Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

How do I change a broken beltoon Eureka altima I can't get to the roller how do I get the piece off

Here is a link to the owners manual which has instructions and a link to the belt you need.Eureka Altima Owner's Guide ... Vacuums

I have a new STEAM VAC Dual V All Terrain Carpet and Hardwood Cleaner. I have used it once and it worked well. Now, the second time, I have no water return. I checked the tank location, the brushes are moving slowly (but the plastic surrounding around the brushes moves as well ??) Water is coming out. There is hot air blowing out, but there is no air suction. What is wrong? Ursula Litzcke

Hello litzcke.\015\012There are lots of people facing this problem as well as other problems with this machine. As there are lots of faulty with this product; would not **** up water/air/shampoo, will not brush and lots more. If it is under war ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0650 seconds