Having problems with your Eureka Vacuums ?

Eureka model 71 how to clean the brush roll

\015 The brush roll is really clogged with hair, the guy at Eureka just told me to use scissors (idiot) i cant get all the hair stuck on the sides of the roller with just scissors...can you help or do you have instructions on how i can remove the roller completely so i can clean it properly?\012Tx. much!\015

Answers :

Repair Help & Product Troubleshooting for Eureka Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka model 71 how to clean the brush roll

... Eureka Vacuums

How do I remove the brush roller onthe eureka clean living vacuum model no 3281 AZ

... Eureka Vacuums

I have a Eureka The Boss Mini (Model # 442) vacuum cleaner. It is not working properly sometimes Today I did a cleaned the roller brush thoroughly and powered it on to see if it spins at all. It spins only in Carpet model, but stops sometimes. Please can you tell me what could be the problem?

... Electrolux Vacuums

The brush won't roll so i guess i need a new belt. the one there is intact but seems loose. Any other suggestions? Thx. Lynn eureka the Boss Model 405 and type B1.

... Eureka Boss SuperLite Bagless Upright Vacuum, 405AVacuum

Hello, I have Kenmore Vacuum Cleaner Model 116, serial # DH1037491. The brush roll does not spin. I do not know how to take it apart and clean. I will appreciate very much any advice. Thanks in advance

... Kenmore 33721 Upright Vacuum

I have a eureka Air speed vacuum model AS1000 that won'tclean on carpets only if I use the cleaning tools. Is it the brush or belt?

... Eureka Vacuums

The brush roll on my Eureka Bagless The Boss 4 dimension cleaning vaccum itsn't working. How do I fix it?

Take either the plate over the brush roll off, if it doesn't come off, then the top cover comes off, should be 2 or 3 screws on the top to remove. Then you can get to the belt and brush roll. Check the brush roll, make sure the ends turn freely, if ... Eureka Vacuums

How can I disassemble the Eureka Altima Brush Roll (#60844-7) for cleaning? Thank you, Jerry in Irving, TX

You can remove the two screws in the top cover above the roller. Then lift off the top cover exposing the roller. You can then pull the roller out, and clean out the cradles that hold the end caps. The square end caps can also be pulled off the be ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Brush rolls of my Euro-Pro Shark vacuum (model-UV 210CN) are stuck; the brush is unable to roll. Does that mean I have to the roll on one end or the whole brush unit? I live in Canada and if possible let me know where I can find a store. Thank you.

... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,

It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

Dc07 problem I have a dc07 cyclonic vaccum and like this model,however, for some reason,it has been very dificult to push and pull for the past month or so. i have completely cleaned the brush assembly,cleared any obstructions in the hoses,and, cleaned the filter.I also checked the belt tension,wich i thought was fine but to no avail.Be advised that the brush assembly is spinning and suction is excellent. It just feels like the brush drags along the carpeting. this is a great vacuum cleaner and

The dyson uses two belts, one from the motor to a clutch and then from the clutch to the brush roller, the belts that they use are not much better then any other belt ( those you should change yearly ) but you cant just change the belts you have to c ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

My Roomba says to clean the brushes when the brushes are already clean. Is there something to take apart to check? I have already taken the brushes out. I don't know the model number, I think it's the 500 series, black and silver.

Turn the unit upside down and remove the bottom pan should be 4 or 5 screws depending on the model. next remove the 4 screws that hold the brush cartridge and pull the whole brush assembly out.using a can of compressed air cle ... Roomba 3005 Pro Robotic Vacuum

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab

(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

I have a similar problem as many do with this model, "clean Roomba's brushes".. We took it apart last night, cleaned out all of the dust we saw. we removed the cover, the housing for the brushes and everything else we could. Still has the same problem. What now?

Mine did the same thing and no mater how much I cleaned the brush or pulled fibers of the ends it did not stop until I:Removed the little yellow tabs on the ends of both brushes and used a tooth pic to remove the built up inside the bearing ass ... iRobot Roomba 530 Robotic Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

I would like to find where I can buy the battery 391504 the Eureka easy clean cordless model 97 type A, or where I can purchase an easy clean cordless model 97. Thank you Marzi

I would look on craigslist or ebay. ... Eureka EZ Kleen 97A Bagless Handheld Vacuum

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.

Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

How is the V-belt tension adjusted (Hoover Model U6439-900)or how do I know if the tension is correct? There seems to be a lot of "play" in the belt and I'm wondering if that is the reason the brush roll only turns as the wheels turn, regardless of the carpet height setting. And yes, the brush roll is set for carpet, not hard floor. Or is the cause of the problem something other than the V-belt? A new flat belt was installed when the machine was professionally serviced so I assume (?) that was a

The V-Belt is not adjustable. There are two ways the belt has no tension: (1) when the handle is upright, a mechanical lever takes the drive tension off the belt, and (2) the brush roll lever setting you described. The upper handle would have to be ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.

... Bissell Vacuums

I live in Mexico and have a Electrolux Easy Box Vacuum...I am looking for a hard floor brush that will fit the hose as my old Sears brushes are a little too small.This model is bagless and may only be sold here,but I do not care for the floor/rug brush combo brush as it does not clean tile floors very well.I would order and have a friend in the states bring to me.Thank you,Linda Staton Cozumel Mexico

... Electrolux Vacuums

Hoover Max Extract LS F6056900 Hand Tool not working / Cleaning Solution I need to know what I need to get in order to have the hand tool work on this model. Also, what cleaning solution is best for pet stains? Tried cleaning, pre-treating with Spot Shot and towel and/or scrub brush, then cleaning, still doesn't work. PLEASE HELP!!

... Vacuums

My eureka 5902 4D bagless uprights roller brush stopped spinning. The belt is ok. This model has a sliding switch for roller speed. The brush should spin when you release the handle via the foot release. Bad brush motor or is there a fuse involved?

The same thing happened to me about a year ago with this very model. \015\012The issue on mine was a small, copper-colored metal wheel that attaches to the end of the brush roller. You'll need to remove the top cover (there are several screws). ... Eureka Smartvac 4870 Bagged Upright Vacuum

No matter how many new belts we put in the brush will not rotate when it touches the floor. If you hold it straight up the brush rotates like crazy. Why is the brush not cleaning the floor. Yes, I have the right belt. It is R we have the boss. 12 amps. Model 4870

There is probably an accumulation of slippery stuff on the shaft that drives the belt. You can scrape it clean with a sharp knife or a razor blade. You might need to use some kind of solvent to get it clean, and if you do, be sure to follow up wit ... Eureka Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0950 seconds