Having problems with your Eureka Vacuums ?

We have the Eureka EZ Kleen upright. We have suction through the hoses but not the main vacuum. The brush turns fine but the vacume does not **** anything up.


Answers :

THE HOSE BETWEEN THE DETACHABLE WAND AND THE BRUSH ROLLER AREA MUST BE CLOGGED WITH CARPET FIBERS. CLEAN IT OUT AND IT SHOULD WORK.
\015\012
\015\012SFC ANDERSON, RICHARD T US ARMY
Repair Help & Product Troubleshooting for Eureka Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

We have the Eureka EZ Kleen upright. We have suction through the hoses but not the main vacuum. The brush turns fine but the vacume does not **** anything up.


THE HOSE BETWEEN THE DETACHABLE WAND AND THE BRUSH ROLLER AREA MUST BE CLOGGED WITH CARPET FIBERS. CLEAN IT OUT AND IT SHOULD WORK.\015\012\015\012SFC ANDERSON, RICHARD T US ARMY ... Eureka Vacuums

I have a Dyson DC14 It started making a high pitched squeel so I took the filters out and cleaned them and i checked all places that pull out on the vacume to see if there was anything clogged. I also cleaned the roller brush. but when I turned it on, after a couple of seconds the sound came back again. can you help


Sounds like motor bearings are gone .... sorry. ... Dyson Vacuums

Purchased ProHeat 7920 Po-Tech recon. Unable to use main brush as no water/cleanfluid. Belt drive is ok. Grateful advise location of fluid jets as not visable behind main brush. Turbo brush works well.


Make sure there is liquid in both the Tank-in-Tank and the SmartMix Bottle and check for spray through the upholstery hose. If the hose does not spray please check the following:\015\012 \015\012- Remove the belt access door and ... Vacuums

My model F5906-900 --- problem is the brushes have stoped working... I pulled the brush assembly out by holding the two tabs, and all seems clean and the brush assembly rotates easly... onced the brush assembly is removed. What I did notice is the female driver slot (found in the main assembly unit) that drives the brushes seems stuck..Is that normal when the machine is not hooked up to power? How can I get the brushed going??? it is a good machine, but the brush options is important too it's ab


(1) Assure the Brush Control on the hood is NOT set to the OFF position.\015\012(2) Remove the brush assembly by pulling/unlatching it from base on each side.\015\012(3) Does one of the brushes ... Hoover F5906-900 Upright Steam Vacuum

Dyson hi my dyson sounds as if something is catching when the brush goes round, it's very loud, it still has good suction. I have taken the plate of can't see anything or fell if there is anything obstructing the brush, could it be the belt?


Hi.\015\012If the brush turns freely then you will need A new clutch unit fitted to your machine.\015\012There are loads of them on Ebay very reasonabley priced only buy new not second hand.\015\012\015\012Manuals are availabl ... Dyson DC07 All Floors Bagless Upright Cyclonic Vacuum

I have a Electrolux , EL6988 Canister Vacum, howeveer the brushes and motor will not run when turned on. I have take the plates and cleaned around the brushes, but it will not come one. The vacum comes on but the motorized bushes do not activate. Thanks I have lost my owners manual, and have looked for the reset button and can't find or know where it is located. Any suggestions.


I need the molded wire harness inside the plastic wand ( one of the prongs is broke off) What is the part # or where can I buy it? Model EL6988 ... Electrolux UltraLux 2000 Bagged Canister Vacuum

When i start the vacum the brushes trun for about 3-5 seconds then stops. the vacum still runs,its just the brushes stop turning, what should i do?


If your machine has no power or interrupted power, please check the following:\012 \012- Make sure the power cord is plugged into a functioning outlet to check for power.- The handle may not be installed properly, causing a ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

The brush on my Electrolux Ambassador III vacum stops turning after vacuming for only a few minutes every time I use it. The power nozzel is less than a year old and except for the brush not wanting to turn, it operates just fine. Any suggestions on how to fix the problem?


... Electrolux Vacuums

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?


If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

Vaccum brush not working. Filters clear of debris has been smoking will not **** anything up help! I cleaned the brush up, cut hair out, etc. Still the brush will not turn and it smokes a little, is this a belt problem?


Yes you need to change the belt. Here is a link to the belt you need and to a manual you can view:Bissell Lift-Off Revoluti ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

My bissell 82h1 has developed a very loud clattering noise. I cleaned the brushes and checked everything I could easily access to no avail. When I turn it on with the brush removed, the sound level is normal. With the brush in place, I can easily turn it by hand with no indication of it hitting anything.


... Bissell 82H1 Cleanview Helix Bagless Upright Vacuum

The brush on our Dyson DC07 isn't moving - the band has not broken, is still attached but not moving the brush. the hoover is still sucking up dirt but not brushing anything up


Check beside the on/off switch. My model has a button beside the on/off switch that turns the brush on and off. It just has a picture on it no word. Hope this helps! ... Vacuums

Beater brush my beater brush will not move check for anything in the brush just bought the vaccum 30 days ago


Note: The brush will not rotate when the machine is locked in the upright position, because an internal micro-switch turns the brush motor off.\015\012\015\012- Make sure brush switch on the handle is on.\015\012\015\012- Chec ... Bissell Healthy Home HEPA Bagless Upright Vacuum - Metallic Blue

I snagged a loose throw rug with the Dyson last night. It jammed the brushes which stopped spinning, Once I removed all the entangled fibers the motor won't turn. The vacume still sucks, but the brushes don't spin I'm concerned I burnt up the motor for the brushes


Have you checked the belt? You can do so by removing the bottom plate from the power head. Once removed, check the belt. If broken or worn, it needs replaced.\015\012An instruction video for replacing the belt can be found on the below link. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Dyson Ball DC24 brush turns but is loose and makes a very loud noise. Brush seems to be hitting sides of vacume.


You need a new brush and end cap. The brush and end cap can wear or break in time as they are made of plastic. Spares available on Dyson web site. ... Dyson Ball DC24 Bagless Upright Vacuum

Main Brush Failure


The belt may look fine but it can be stretched or worn. You can get replacement belts here:Bissell Lift-Off Revolution Replacem ... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

We lost our instructions to the Kirby Shampoo attachement and how to attach it to the main unit, the belt and how to use it. We need complete instructions and explanations on how to use this as we have tried and the belt does not attach to the main unit, the brush does not turn and the hops along the carpet and no water, etc. returns to the tray. Please help us with as simple and complete instructions as possible. THANK YOU VERY MUCH, LOUIE CAPLAN


First, you'll need to fill the tank with water (warm or cold). There are three fill lines on the side of the tank. Fill to the desired line and add one shampooer tank lid full of Kirby shampoo for each line of water. A full tank will require th ... Vacuums

Hoover 6446 900 WindTunnel Bagged Upright has little suction at the floor brush but plenty at hose if disconnected. It does not seem that there is anything blocking the inlet at the floor brush.


Check for a clog in the brush hose ... Hoover Tempo Widepath Upright Vacuum - Blue

My husband go the brush tangled in something. We cleared all of the obstructing string from the carpet fringe and the brush is moving freely but it still is making this awful noise when I try to use it like it did when it was tangled up. Is there anything I can do to fix it or do I need to find a repair person?


Probably your belt have a spot where i wored out when it got tangled up inspect the belt first ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

My dyson animal vacum hose no longer wants to **** up anything i have removed the botttom part that u can unscrew and removed somethings that were stuck in there since then it no longer picks up anything any suggestions


Check all connections and motor ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Roomba give message to clean brushes even when I have cleaned brushes, wheels, and anything else I can find. It will only clean about 3 minutes.


Pull 2 roller brushes off.remove funny lookin yellow ends clean hair ect. also pop out front wheel and clean ... iRobot Roomba 560 Robotic Vacuum

I followed the instructions above and found that neither brush turned. when no brushes are in and the vacum is running the gears are not turning either when i look inside the unit


You need to clean the gears hidden in the housing itself. they have become clogged with hair etc and wont turn.This will require you to remove the housing. ... iRobot Roomba 530 Robotic Vacuum

Brush Hi I just bought a Kirby second hand. There is a small black rubber belt hanging off the brush. How can I take apart the bottom part of the vacume and where does this belt go to. Thanks Anita


Check out my step by step instructions...\015\012\015\012http://reviews.ebay.com/CHANGING-T ... Kirby G4 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0499 seconds