Having problems with your Eureka Vacuums ?

I havc a boss smart vac and it does not **** well especially throught the hose. I have lost the handbook. have recently replaced the belt. still does not work right. help


Answers :

Sounds like either there is a clog in the hose or the paper bag is not installed correctly.
\015\012If it as a bagless machine, clean all your filters thoroughly....let them dry completely before putting them back in.
Repair Help & Product Troubleshooting for Eureka Vacuums

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I havc a boss smart vac and it does not **** well especially throught the hose. I have lost the handbook. have recently replaced the belt. still does not work right. help


Sounds like either there is a clog in the hose or the paper bag is not installed correctly.\015\012If it as a bagless machine, clean all your filters thoroughly....let them dry completely before putting them back in. ... Eureka Vacuums

Brush Roll belt stops turning durring vacuuming on WindTunnel self-propelled, v belt is a little loose with handle down. Tensioning roll is engaged OK, but fully at the end of its travel. Replaced belts flat and v, but still stops turning even on high carpet setting when vacuuming. Carpet setting and height adjustment appears to be working OK, roll is clean and turns easily when out. Also turns easily until it engages the carpet. Self propel function works just fine.


... Hoover U6485900 Bagged Upright Vacuum

The hoover windmill brand new, new belts not working, replaced new belts with new belts still not working its a useless piece of ****.


... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

I have a Hoover pet cyclonic upright model uh70085. the brush won't spin, I thought maybe the small belt was stretched, I ordered the correct replacement belt and replaced it, I still have slack and the brush won't turn. the floor and brush adjustment seems to be working correctly. Thanks, Tom


... Dirt Devil Hoover Uh70085 Pet Cyclonic? Upright Vacuum

Dear Sir/Madam, My old faithful Hamilton Beach Mixer, now 60 years old, is still working but recently I was told by someone who looked at the motor that it needed repair or replacement. Is it still possible to get it in working condition?


If the armature shaft is worn there might be a problem, but that would be about the only one, Bushes/bearings can be replaced as can brushes. If the armature shaft is worn, a fix can be formulated but it will require some ... Vacuums

I have a Dyson all-floor model (not the ball). I recently replaced my carpet to a Frieze. Since replacing the carpet, the Dyson is extremely hard to push. It almost forms a "seal" with the carpet. Seems to work fine on Berber carpet and laminate floor. My husband has checked to make sure the brushes are working, hoses are not clogged and belts are OK. I've had it for about a year. It is virutally impossible to push on the new carpet. Any ideas?


Have you adjusted the brush control system. If you look at the link below page 6 will tell you how to adjust. If this is not you vacuum please give the model # of the one you have so I can help you more.\015\012\015\012 ... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I have a kenmore grab n go bagless and I need to know the exact size of the belt, I lost the manual, and I have burn several belts at the bigining of the problem the motor stops and burn the belts I open it and I think it was a little piece of plastic, that cause the problem, but when I put the new belt it looks like the motor works fine,but still burn the belt, I'm using UB-1 #5275 belt am I using the wrong one?


... Kenmore 34722 Grab-N-Go Upright Vacuum

After using switch to go from floor to carpet, noticed the roller brush not working, and therefore the self-propelled feature also not working. Replaced what I thought was the problem, a loose belt, but still does not work. Motor runs and there is suction...???


... Hoover Ultra U6430-900 WindTunnel Bagged Upright Vacuum

I have a Bissell 1623-1 Steam Cleaner. It will work good for about 2 minutes and then after that it will not dispense cleaning solution on floor or through the hand held wand.I have replaced both drive belts with no improvement. I have cleaned it and found no obstructions in hoses and spray nozzles, put back together and it still will not dispense. Is it possible the pump or solenoid is no working? Aaron


... Bissell 1623 Steam Cleaner

I have a Kirby Heritage II which normally works amazingly well, but it's not playing at all nicely today - and of course we have apartment inspections tomorrow. *dies* The belt broke today (as did the replacement belt, which I'd bought at the same time, so apparently the rubber was old), so I went over to Stark's to get some new ones - but it still won't cooperate. I've taken the head apart and put it back together several times, to be sure that everything is properly seated, but it's just not


... Kirby Heritage II Vacuum

I have a WRPL 25P Dehumidifier, Serial # NQ336USA2733, that I purchased at Canadian Tire, Corner Brook, NL, Canada on July 25, 2009. I recently noticed that the dehumidifier wasn't working. When I turn it on, it just blows cold air and does not absorb the moisture in the air. I am wondering if it is still under warranty. Please advise if the product is still under warranty and what steps I need to take to have it repaired or replaced. Thank you.


... Vacuums

My Rainbow E2 has been working great for years now, but recently it has stopped working on the vaccuuming setting, but will still run on the low speed air cleaning setting. I hope it is something as easy as replacing the switch. Would appreciate any tips to determine if that is the issue or possibly something larger. Tks in advance for the info/help.


Still need help, let me know.\012\012Thank you,\012Ralph ... Rainbow E series Canister Wet/Dry Vacuum

I have recently replaced the belt and filters. The belt is in the correct position and the rotating brush moves freely. The motor is very loud. It still vacumns but I'm afraid the motor will burn up.


Does it sound different than it did before you made the repairs to it or does it sound the same. Just so you know some of the upright vacuums on the market today sound like a jet airplane landing in your living room.Ca ... Bissell 6594 PowerForce Bagless Upright Vacuum

Bissell revolution brush not working -replaced belt -still nothing


Hi\015\012\015\012The brush will not rotate when the unit is locked in the upright position, because an internal micro-switch turns the brush motor off.For the brush to rotate and the headlight to light, the brush switch must be on and th ... Bissell Vacuums

I LOST MY INSTRUCTIONS DISK TO MY KIRBY G SERIES AND I DONT KNOW HOW TO DO ANYTHING WITH IT. I JUST REPLACED MY BELT BUT IT DOESN'T SEEM TO BE WORKING AS WELL AS IT SHOULD.


We have a video, online and printed manuals HERE. ... Kirby Generation 3 Bagged Upright Vacuum

I have a power drive baggless vacuum cleaner...it runs well, but suddenly it seems to have lost most of the suction coming through the hose and floor area. When I remove the dirt container, the suction below it seems strong. I have had it to repair twice--they have tuned it up and replaced all filters and belt. It still does not pick up well when I vacuum or use the hose. Can you help ?


There is something stopping it up,you will have to dissasemble the unit to find the blockage,this is the most likely problem. ... Hoover U6660-900 WindTunnel Bagless Upright Vacuum

I have an older Oreck XL that has worked great. The belt recently broke and I reinstalled a new one but now there's a rattling noise like something is loose and a burning smell. I've cleaned it as well as I could but still nothing. Help please!


When you turn it on, is the brush roll spinning? (Check carefully, as lifting the unit from the floor exposes a brushroll that should be spinning at a high RPM.)\015\012\015\012Did you get the brush roll properly seated in the slots? Does ... Oreck XL Ultra Bagged Upright Vacuum

Bissell proheat 1699....just replaced the pump belt and still not working.


Try taking all the hoses off one at a time and see if any are clogged. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

The original belt on my upright Kenmore Progressive broke and I replaced it with the spare that was in the vacuum. The vacuum and spare belt are about 10 years old. Then the spare broke after one vacuuming session and there was a burning smell coming from the vacuum. I ordered new belts and replaced it with the new belt. It seems to be working fine with no smell. I checked the belt after I vacuumed the family room and although it was in tact, the belt was very hot. Is that normal? Should t


The belt heats up due to the friction, as well as being in contact with the shaft of a hot motor. It is normal. ... Kenmore Progressive 35922 Bagged Upright Vacuum

I can't find replacement belt for little lux (original model bought in 1991). Stamped on back "Model 1673BA". Motor works fine but belt doesn't turn roller any more.


... Electrolux Little Lux Bagged Handheld Vacuum

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......


Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef


Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

The motor on my Epic 6500 works, the hose is sucking, but the power head isn;t working... I tried the sidestep power head and that one works. Ive opened and replaced the belt and that is fine. The bulb was already burned out and wasn't replaced so I cant tell if theres power to the head. What else could it be?


Connect the power nozzle directly to the hose and try.\015\012Check the terminals where the wand connects to the PN. If any are discolored or cracked, that may be the problem.\015\012Open the PN and check for loose or broken wires and co ... Electrolux Epic 6500 Vacuum

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.


I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0892 seconds