Having problems with your Eureka WhirlWind 4381 Upright Vacuum ?

Eukerka lite speed

\015 How do I change the belt on a eureka lite speed, belt is a U thanks\015

Answers :

There are 2 screws on the top cover, remove those and the cover comes off, then you can get to the brush roll and belt. Inspect the brush roll, make sure the ends turn freely, if not, then replace it also.
Repair Help & Product Troubleshooting for Eureka WhirlWind 4381 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eukerka lite speed

There are 2 screws on the top cover, remove those and the cover comes off, then you can get to the brush roll and belt. Inspect the brush roll, make sure the ends turn freely, if not, then replace it also. ... Eureka WhirlWind 4381 Upright Vacuum

My Eureka Lite speed whirlwind has a bad odor when it runs.

It is either the filter or on the roller or belt.\015\012\015\012\015\012 ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara

... Vacuums


... Vacuums

Vacuum cleaner We have a panasonic MC-E47electronic which seems dead. It has a speed control which we nearly always had on full anyway. Have tested continuity through plug, flex and on/off switch and all OK. from then is open circuit through speed control which consist of slide rheostat and mystery small green box (2cm x 2cm x 1cm approx). Across motor there is negligable resistance. Machine is quite old and not worth paying out loads on poarts if it is safe to bypass speed control and connect

Yes it is safe, but i would make a switch? ... Vacuums

I bought a Tacsew T8700 High Speed Stright Stitch and I should have paid more attention to the 'High Speed'! The motor that came with this industrial machine is a Tacsew Clutch Motor model: RM1878-1H. It is way too fast when starting out and usually breaks the thread. The local company I bought it from told me there was not a user manual for the machine or the motor :P. I've finally gottin the tensions adjudsted but still need to be able to start sewing at a slower speed. Any advice out the

If you are just starting off sewing and don't have good foot control change the motor to a d/c motor they are about $120 and you can turn the speed of the motor up or down ... Vacuums

Oreck trouble I replaced the plug and switch. black from motor to pole 1, black from plug to pole 2, white tied to white with a wire nut. When I plug it in it is powered in the off position. I have high speed at the high speed position, low speed at the low and off positions. Any ideas?

... Oreck XL Ultra Bagged Upright Vacuum

Oreck XL upright - has a 2 speed switch. Now only works in high speed not low speed. Will a new switch correct or is it the motor

Your vacuum is fine. The switch can either run at full speed or half speed. You are running at full speed, you need a new 2 speed switch. You can pick them up at an Oreck Store for $29 or around $15 on eBay ... Oreck XL Ultra Bagged Upright Vacuum

My HEPA Shark Model 238 is great when the moter operates at high speed. However, periodically, it slows down resulting in no turbo action and virtually no pick up of eve the lighted dustball! Sometimes a good swift kick will bring the moter speed back to "HI", but sometimes no matter what, it won't speed up.rnHELP!

If the motor is over heating, it will slow down and may even stop all together. A solid knock could reset the thermal switch prematurely. Clean it as best you can around the motor and try it again. If it does the same thing, turn it off for 20 minute ... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

The e series rainbow 2 speed works only on low speed. High speed will not run. What is srong?

It is either the switch or the controller. Call us and we can see if it is still covered under your warranty.RainVacwww.rainvac.com800-523-0510 ... Rainbow E series Canister Wet/Dry Vacuum

I have a Dirt Devil magnum MPR and the problem is that after working for some minutes it slows down and then works at an erratic speed. I suspect it is the speed control pot. Any help? Thanks

... Vacuums

I have a remote Hunter Ceiling Fan w/ remote 1-2-3 fan speed buttons and one on/off/dimmer light button. Model Number CP-9110R. It only has one pull string and it is for the light. I would like convert the light to work off of a simple wall on/off switch and the fan to be controlled by a 3-speed pull string. Can I by-pass all the sensors and make it work?

I see noone has answered so I will.Yes,it could be done,but if there is not a conversion kit for your fan,it would not be wise to do it.For starters,all of the things required would probably cost at least $15.Also,there is at least one tool you would ... Vacuums

I have a VX3000C Broan vacuum and the motor sometimes runs lower and comes back to normal time and time. Plus, now it lamost stops before coming back to normal speed. Can someone explain to me what that might be or if it did happen to someone else? It doesn't stop, but runs at very low speed and come back. It is like if a connection is not made properly. But it does the same at my 3 connections and I did check the one on the vaccuum itselfs.

... Broan-NuTone VX475 Bagged Central System Vacuum

Despite having the small window cleaned out the brushs will not spin at high speed. They turn at the low speed only.

... Hoover V1 SteamVac SpinScrub Vacuum

Red devil quick lite spitting out dirt - Dirt Devil Easy Lite Quick Vacuum

... Dirt Devil Easy Lite Quick Vacuum

Hunter Fan model # 27185-060 - Fan high speed does not work - only get low speed by use of the remote- how do i fix this ???

... Vacuums

My oreck xl is a 2 speed but only works on low speed

... Oreck XL Ultra Bagged Upright Vacuum

I have an older Bernina 830 Record sewing machine and I've noticed that it makes a growling noise when I first step on the foot control with the machine in the low speed setting. The noise goes away when the speed picks up. Is this serious? What's the fix?

... Vacuums

Screeching sound coming from motor area,smell of burning,motor speed dies down and speeds up , screeching gets worse. carbon brushes are ok.

How is the fan, any fins broke off? Could be bad motor bearings, problem with the armature. ... Kirby G4 Bagged Upright Vacuum

I have a Kirby G7 and it will run on the low speed setting. When i switch to the high speed it starts to spark and smoke near the back of the motor near the windings. Do i have a motor going bad or is there a simpler fix.

It's probably doing that on low speed too, you just aren't noticing. What you'll have to do is get to the motor. Look at the armature and see if it's scared, missing an pieces, scratched up.. if so, then your motor is shot, throw it away.. If not, if ... Vacuums

I have a lemon Hampton Bay 52" Redington III and the highest speed is stuck on medium (about 100 RPM), but all 3 speeds are different, and I have seen those fans in Philly Diner faster than that. HELP!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Hello,Hello,please can you rephrase this question so that an accurate solution can be proffered? I don't really understand the question and its not clear enough.I look forward to your reply.Bye for now. ... Vacuums

The low speed for bare floors won't work at all. The regular speed for vacuuming carpets turns on but spits items back out after a little bit.

There is only one speed on a central vacuum. The power nozzle motor has nothing to do whether or not you have suction. Sounds like you don't have any suction. Unplug your hose from the wall. Start at the unit. Short out the two low voltage wires atta ... Electrolux Central Vacuum

I bought a Hampton Bay Hawkins 44 " ceiling fan (117 391) and would like a remote that I can control the speeds with not just the on and off. I have a pull chain for the speeds but would like to use a remote instead. Is this possible? I have a Hampton Bay Redington IV and love the remote. I'm looking for something like that. Thanks Madeline Lepisto

... Vacuums

My rainbow vacuum will not start in high speed but runs in low speed

Yes, it sounds as if your controller is bad. Give us a call and we can see if it is still covered under your warranty.RainVacwww.rainvac.com800-523-0510 ... Rainbow E series Canister Wet/Dry Vacuum

Dirt devil lite not sucking - Dirt Devil Easy Lite Quick Vacuum

... Dirt Devil Easy Lite Quick Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.3091 seconds