Having problems with your Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum ?

What belt do I purchase for eureka whirlwind litespeed


Answers :

Hello,
\015\012
\015\012If you have the exact model Eureka that this repair was listed under, model 4388 then please find a link to the belt you need below. If you'd like to verify the model number, please check the back or the bottom of the vacuum for a sticker that also will contain the serial number, and look for the word Model Number. If you don't have the 4388, please just add a comment with the model you have and I'll be more then happy to verify these two models take the same belt, or give you a link to the belt that goes to your model if they are different.
\015\012
\015\012Here's a link to the exact belt called for on the model 4388:
\015\012Eureka Extended Life Style U Belt, Part 61120
\015\012
\015\012Here's step by step instructions on how to replace the belt:
\015\012
\015\012How To Replace Brush Roll Belt
\015\012NOTE: Turn off the switch and unplug the electrical cord
\015\012before replacing belt. Belt pulleys can become
\015\012hot during normal use. To prevent injury, avoid
\015\012touching the motor pulley when checking the belt.
\015\012
\015\012
\015\012
fa435ec.jpg\015\012
\015\0121. Lower handle to floor to change belt.
\015\0122. Loosen, but do not remove, two screws to release hood.
\015\012Lift hood to remove.
\015\012
\015\012
\015\0128f6c19a.jpg\015\012
\015\0123. Lift left end of brush roll.
\015\0124. Remove and discard belt.
\015\012
\015\012
\015\012a4f21e8.jpg\015\012
\015\0125. Place new belt around motor pulley.
\015\012
\015\012
\015\012bce371a.jpg\015\012
\015\0126. Place belt around brush roll pulley.
\015\0127. Align left end cap with square in base. Push
\015\012end cap into place; see left side view.
\015\012
\015\012
\015\012128701f.jpg\015\012
\015\0128. Pull right side of brush roll to stretch belt.
\015\012Secure right end cap into base.
\015\012
\015\012
\015\01245ae0ad.jpg\015\012
\015\0129. Rotate brush roll to seat belt.
\015\01210. Replace the hood. Make sure hood front is
\015\012behind furniture guard. Hood should seat
\015\012onto self-locating screw tabs.
\015\01211. Tighten screws.
\015\012
\015\012
\015\012I hope this information was helpful to you in changing the belt. If you have any questions about how to change this belt, please just add a comment here on the repair page of Fixya, and I'll be happy to answer any follow up questions you might have. If you found this helpful, please be so kind and rate my repair helpful and / or leave feedback for me.
\015\012
\015\012Thanks so much,
\015\012
\015\012Chris Jones
\015\012GoVacuum.com
Repair Help & Product Troubleshooting for Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

What belt do I purchase for eureka whirlwind litespeed


Hello,\015\012\015\012If you have the exact model Eureka that this repair was listed under, model 4388 then please find a link to the belt you need below. If you'd like to verify the model number, please check the back or the bottom of ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

Eureka whirlwind lite which belt? - Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum


... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

How do I take the roller and belt off - Eureka WhirlWind Litespeed 5844 Upright Vacuum


Open bottom cover, and pull it off. ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

What size belt does a eureka whirlwind litespeed 5841 take


... Vacuums

Replace brush roll belt - Eureka Whirlwind LiteSpeed 5843 Upright Vacuum


... Eureka Whirlwind LiteSpeed 5843 Upright Vacuum

How do I replace the belt on my mom's Eureka Whirlwind litespeed 12 amp 15" ?


Take the cover off from the bottom there should be clips or screws on the bottom.and work the old belt off and new one on ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

The vacuum roller won't turn but the belt is fine Eureka Whirlwind Litespeed


The belt may look fine but it's probably stretched out. Rubber belts are usually good for about 1 year. The tension of the belt is what allows it to turn under the strain of the carpet. Make sure the brushroll spins freely when held out of the machin ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

Eureka Whirlwind LiteSpeed 5843 manual - Eureka Whirlwind LiteSpeed 5843 Upright Vacuum


... Eureka Whirlwind LiteSpeed 5843 Upright Vacuum

What size belt does a eureka whirlwind take - Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum


Hi,\015\012\015\012Your Eureka Whirlwind 4388 takes Eureka Style "U" Belts, Part number 54312. \015\012\015\012Here's a direct link back to that belt on our website if you need to purchase one:\015\012 ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

Eureka whirlwinde litespeed vacuum - model 5841


Very simple under all three screws in the front (two on sides and one in back) once open--you can take off that panel...take brush out...take old belt out...put new belt on..around brush..place both inside...and make sure belt is around that little p ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

Changing belt - Eureka Whirlwind 5740


I tried the website for manuals but no luck. I called the toll-free # 1-800-282-2886 and got a rep right away. I gave him the model and s/n (lower bottom on the back side) and he walked me thru it. For the model I have, there are 3 screws to remov ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

How to change belt on Eureka Whirlwind


On the top cover, there are holes at the front on both sides, there is a screw on each side in one of the holes. Take the out, and the cover should come off, then you can get to the brush roll and belt. ... Eureka WhirlWind 4381 Upright Vacuum

Belt location i have a eureka upright the boss whirlwind lite and i need to change the belt. I have no clue where to find it. Need help with this


If you torn the macine over, at the bottom of the sweeper you will see the belt on on side. You have to take the bottom part apart and remove the brushes to replace the belt. I hope this helps. ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

Eureka 3277 AVZX manual - Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum


... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

I have a eureka surface max 300, i saw smoke come out of my vacuum i seen that the belt was broke every time i change belt i run it on it snaps every time ive put 3 new ones and each one break right when i start it it looks like the metal piece is burning it is there a piece missing?? what am i doing wrong?? ugh i just purchased it couple of months agoo not even older then 6 months .. what do i do?


... Eureka Capture Upright Vacuum Vacuum

How to change the belt on eureka 3281az - Eureka WhirlWind 4381 Upright Vacuum


... Eureka WhirlWind 4381 Upright Vacuum

Manual eureka 5740 - Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum


... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

Eureka whirlwind+ Is there a belt!? Smell hot like burning rubber...can't locate a belt to change?


It's a little tricky but here's how you get to the belt:Once you have removed the housing and the roller, turn the vacuum so that you are facing the pin the turns. Pull the belt to the back of the un ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Change belt on eureka clean living 3281bz - Eureka WhirlWind 4381 Upright Vacuum


... Eureka WhirlWind 4381 Upright Vacuum

There is a metal post that spins and rotates the belt at the opposite side from the brush. the removable wheel that holds the belt onto the metal pin is missing. how can i buy that part? eureka whirlwind lightspeed #5844


Vacuum 24x7.com, they should have the parts ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

WHAT PARTS COME OFF WHIRLWIND - Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum


... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

Change belt for eureka powerline 4773 - Eureka Powerline LiteSpeed 5845 Upright Vacuum


... Eureka Powerline LiteSpeed 5845 Upright Vacuum

Change belt How do I change the belt Eureka whirlwind 4480. As I look under the house I think I see one screw on each side down in about 3/4 inch. Are those the screws to remove and are there only two you have to remove?


... Eureka WhirlWind 4381 Upright Vacuum

HOW DO I CHANGE THE BELT ON MY EUREKA WHIRLWIND MODEL 3272


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0476 seconds