Having problems with your Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum ?

Location of belt

\015 Can't find how to get to and replace belt on eureka whirwind model #4388\015

Answers :

There are two Phillips head screws on the cover over the power head. This is the cover that fits around the carpet height adjustment knob. You will notice there are four oval shaped holes on each side of the cover and the crews are in the ones closest to the vacuum handle. The screws are black and may be dust covered and therefore hard to see, but this is all that holds the cover on. When you take these out the cover will lift easily off. Once you do this the motor, belt, and brush assembly are accessible. I purchased a bag of two belts at the local ACE hardware. I recommend cleaning the brush while it is out. Also be sure the bearings on each end of the brush assembly turn freely as hair can work into these and cause them to bind. I hope this helps. [email protected]
Repair Help & Product Troubleshooting for Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

A small belt fell from underneath my bissell steam cleaner and I notice the brushes no longer rotate when I purchase the part where does it go? I tried turning it up side down to find out where it came from don't know because there is a compartment for the belt access but that particular bet is not broken. It's a very thin belt I can not make out the number located on the belt please help.


If you are unsure about where it goes it may have a diagram in the owners manual. When you say you saw a belt in a compartment are you sure that it is not an extra belt you are seeing as they often give an extra in the machine kept in a compartment l ... Bissell 1697-7 Powersteamer Pro Deluxe Vacuum

Belt locfation need to know where belt is located so I can change belt


An eureka whirlwind lite /the boss how to open to get at the belt ... Vacuums

Beater Bar The "Beater Bar" or roller with brushes on it, is not spinning, therefore not picking up. I cannot locate my manual and need to know if it is belt driven and how to get at the belt to identify the size and purchase and install a new belt. Thank you for any assistance. [email protected]


Take off the bottom plate, then you can get to the brush roll and belt, on the model number plate, the number of the belt is on that, it is also on the belt if you can still make it out. ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Looking for new belt for my electrolux guardian canister vacuum power nozzle marked model n106m . have been unasble to locate an appropriate belt replacement. Any suggestions?


This company is now known as Aerus. If you can't find their listing in the local yellow pages, follow the instructions on the folloing site.\015\012\015\012 ... Electrolux Guardian Bagged Canister Vacuum

Belt location i have a eureka upright the boss whirlwind lite and i need to change the belt. I have no clue where to find it. Need help with this


If you torn the macine over, at the bottom of the sweeper you will see the belt on on side. You have to take the bottom part apart and remove the brushes to replace the belt. I hope this helps. ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

Belt how do u locate and change the vacuum belt


Look underneath where the brush roller is located. The brush roller is removed to replace the belt. The new belt is installed on the motor shaft and the brush roller then the brush roller is reinstalled ... Eureka Whirlwind 4481 Upright Vacuum

Eureka whirlwind+ Is there a belt!? Smell hot like burning rubber...can't locate a belt to change?


It's a little tricky but here's how you get to the belt:Once you have removed the housing and the roller, turn the vacuum so that you are facing the pin the turns. Pull the belt to the back of the un ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Belts How do I replace a belt and where is it located. Thanks, Susan


Here is a link to my online guide. Hope it helps!\015\012Marci\015\012\015\012http:// ... Kirby G4 Bagged Upright Vacuum

My fan belt on my hoover is broken,where is it located and how do i fit a new fan belt


I figured out on my hoover upright that many of those models don't access the belt by removing the plate under the vacume. the housing top actually prys off (with the help of a flathead screwdriver). step on the handle release button and lay the ha ... Hoover Vacuums

Dyson DC07 I actually need to locate and replace the brush as it split on one end. Looks like I need to pull the belt off to do that. Might as well replace the belt while I'm at it.


Hi.\015\012\015\012Depending on wether your machine has A clutch fitted will decide how easy this job will be.\015\012\015\012The non clutched model is very simple turn the 3 plastic screws on sole plate to unlock position lif ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The roller has stopped rotating and I wanted to see if the belt needs changing. I cannot find out how to get to where the old belt is located.


Remove the bottom to find the belt. There is usually a spare in the compartment. I think there is 8 or 10 screws.\015\012\015\012Thanks for your interest in FixYa.com\015\012 ... Oreck XL21 Bagged Upright Vacuum

Location of belt


There are two Phillips head screws on the cover over the power head. This is the cover that fits around the carpet height adjustment knob. You will notice there are four oval shaped holes on each side of the cover and the crews are in the ones closes ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

I cannot locate a store in Nashville TN that carries a Royal Dirt Devil Vacuum style 12 belt. Can you?


Try a walmart store ... Vacuums

Our belt broke and now i can't find out where it should go back! The second one broke too so I thought that maybe I was putting it in the wrong location>


Check the brush make sure the ends spin freely if so put the belt on spin the brush with your hands 3 or 4 times around the belt will seat its self ... Vacuums

My Oreck XL 9100HA started smoking (white smoke) when I vacuumed. There is a burning rubber smell. How do I check/change (if appropriate) the belt? I have no User manual, nor can I locate one on the Oreck site. The bag is a new one. The vaccuum had been picking up, though not at its best strength.


It sounds like the belt has been damaged. You can get another belt from yoru local Oreck store. You can even take it in to the store to show them what happened. Purchase another belt and replace it. (It was very easy when I did this, so hopefully ... Oreck XL Ultra Bagged Upright Vacuum

Where is the belt located, and how do i get to it


THE BELT IS LOCATED UNDER THE BRUSH COVER TURN VACUME UPSIDE DOWN AND THERE SHOULD BE SOME SCREWS THAT HOLD THE COVER ON REMOVE THE SCREWS AND YOU CAN REMOVE THE COVER WHERE THE BELT IS LOCATED ... Dirt Devil Vacuums

The brushes on my new healthy home vacuum wont rotate when the machine is turned on how do i access the belt location


If you turn the vacuum over so you can see the brush roll, there is a brush cover that is held on by (4) screws. Remove those screws and the base plate cover will come off. With the base plate cover off you can access the roller brush an belt. If you ... Bissell 5770 Healthy Home Bagless Upright Cyclonic Vacuum

I bought a Clean Broom Electric Co., Model #CBU_5 (SKU# 7986628) Vacuum Cleaner 31CX E 255344. I have need of the following parts 2 belts and brush bearing seals. How do I locate these parts or to find them to purchase them. Thank you for any assistance you can give Tom Freer [email protected] Manufacture Date 0906


I need a screw on filter for model cb9191j-10a vacuum from clean broom electric company. ... Vacuums

How to check the location of the pump belt? - Bissell 1699 ProHeat Clear View Upright Steam Vacuum


Take off belt cover on the left side of the top cover, turn cleaner over, take out screw from red lock and remove, pull cap and brush roll out, unhook the cogged belt, then you can replace the pump belt thru that opening. Put belt over the pump pull ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

How do i get the belt back on the proper location


Hello,\015\012Here are step-by-step instructions,\015\012\015\012http://reviews.ebay. ... Kirby Ultimate G Bagged Upright Vacuum

Vaccum cleaner, (hoover upright) needs new belt, but i can't figure out where it's located.....yes, i'm a woman...lol thank you..


Turn Vac over, remove the plate covering the brush roll, then you can get to the belt and brushroll. ... Vacuums

How to replace belt on rainbow aquamate and locate repair manual on the net


Click on rainbo vacuum in your area, and go from there. I am sure they have a toll free #. ... Rainbow E series Canister Wet/Dry Vacuum

The Dyson motor turns on, but the brush is not turning. What do I do? If it is a belt, we need to know where it is located and how to get into it.


Go http://www.youtube.com/watch?v=7_CtaFcc5HU ... Vacuums

There is no suction when the Eureka model 7685 is turned on. Is there an Air filter? If so, where is it located? The belt turns slowly when the vacuum is turned on. Is that normal?


No you vacuum tub is clogged. Shut off machine and remove hose where attachments go. Use a long handled kitchen appliance like a spaghetti stir to work the jam back and forth. You will be amazed at what comes out. Then remov ... Eureka 4874 Bagged Upright Vacuum

FAN PROBLEM??? good morning! my vacuum smells like burnt rubber (fan perhaps) but I can't find how to get into main part of the vacuum. it's just very rounded with no latches or screws to get inside where the motor, belts and fans would be located. can you help me? thank you


There isn't any belts, and the fan wouldn't be rubber, so not sure what you are smelling. Maybe this picture will help you.\015\012\015\012 ... Bissell 6700 Butler Revolution Bagged Canister Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0586 seconds