Having problems with your Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum ?

How do I change belt for Eureka Whirlwind Lite "Boss" model 450 A

\015 Please provide instructions as I am at a loss as to where to open to get in to replace the belt. \015\012Thanks\015\012Fred\015

Answers :

Remove the 4 screws on the yellow top of the vacuum. The yellow plate will pop up exposing the belt and roller.
Repair Help & Product Troubleshooting for Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How do I change belt for Eureka Whirlwind Lite "Boss" model 450 A


Remove the 4 screws on the yellow top of the vacuum. The yellow plate will pop up exposing the belt and roller. ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

Belt location i have a eureka upright the boss whirlwind lite and i need to change the belt. I have no clue where to find it. Need help with this


If you torn the macine over, at the bottom of the sweeper you will see the belt on on side. You have to take the bottom part apart and remove the brushes to replace the belt. I hope this helps. ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

HOW DO I CHANGE THE BELT ON MY EUREKA WHIRLWIND MODEL 3272


... Vacuums

I can't figure out how to change the belt on my Eureka whirlwind Model #5740 vacuum


Remove 4 screws on top and lift cover. ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

Change the belt on Model#4481 vaccume - Eureka Whirlwind 4481 Upright Vacuum


... Eureka Whirlwind 4481 Upright Vacuum

How do i change the belt in the boss whirlwind lite


Remove 4 screws on top and remove this cover. Belt and roller are easily accessable. ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

Change belt on eureka whirlwind vacuum model 4689


... Eureka 4689 Upright Vacuum

How do I change the belt on Eureka The Boss model 5856?


... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?


First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

Hi I have an electrolux "The Boss" hand held vaccum cleaner. I cannot find the instructions and am having problems changing the belt. It is model number Z57A. Product Number 900-250-006. It is the first time I have had a problem. I only use it occasionally for my caravan. So cant find the instructions and cant remember how to change the belt. Please help


You need top lace belt on brush roller and re[-assemble by putting plastic cover on which is retained by 2 recessed philips screws.. Prize off triangular coverat fornt.behing that you should see the belt lying loose.You need to get a blunt object to ... Electrolux Vacuums

Change belt How do I change the belt Eureka whirlwind 4480. As I look under the house I think I see one screw on each side down in about 3/4 inch. Are those the screws to remove and are there only two you have to remove?


... Eureka WhirlWind 4381 Upright Vacuum

Eureka whirlwind lite which belt? - Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum


... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

Eureka altima model 2993 how to change belt - Eureka Altima Upright Vacuum Model 2996AVS Vacuum


... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Eureka Boss 12 amp Belt change - Eureka Mega Boss 4460DT Vacuum


... Eureka Mega Boss 4460DT Vacuum

Changeing belt I have a Eureka Upright Limited Edition Model 4462D and can not for the life of me find my manual and can not find the screws to take off the plate to change my belt.....help!!!!!


On the top nozzle, there will usually is 2 screws holding the top done. There are slots or holes on each side near the front and the screws or in these holes. Remove them, remove the top cover and then you can get to the brush roll and belt. ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

Changing belt - Eureka Whirlwind 5740


I tried the website for manuals but no luck. I called the toll-free # 1-800-282-2886 and got a rep right away. I gave him the model and s/n (lower bottom on the back side) and he walked me thru it. For the model I have, there are 3 screws to remov ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

My 4870 K Boss is 2 years old. I have replaced belts & filters in the specified intervals. This last time I replaced the belt after a year, it shredded 3 of them on the outside edge of the belt in about 5 minutes of use. I ordered a new brush roller & heavy duty belt which I installed. It began shredding the belt in less than 5 minutes of use. What is your suggestion? Is this a known problem with this model? Eureka says no and is not standing behind it.


The only reason why it would be shredding the belt is if the pulleys were not lined up correctly. Check the allignement of the belt to make sure there is nothing kepping the pulleys from being in line. The other thing that it could be is if the rolle ... Vacuums

I replaced the belt in our Eureka Boss Smart Vac, it still seems loose, it uses a type R belt. The beater belt still doesn't seem to turn properly and seems that it doesn't pick up very well when I use it on my berber carpet. We have 2 dogs and I like to use it frequently. I have changed the bags and belt......


Check to see that the beater brush is not frozen up. Pull the brush and clean it, spraying some WD40 on each end piece that holds the brush in place.\015\012Also be sure the belt is properly installed so that the brush turns in the correct direction ... Eureka Vacuums

How to change belt on Eureka Whirlwind


On the top cover, there are holes at the front on both sides, there is a screw on each side in one of the holes. Take the out, and the cover should come off, then you can get to the brush roll and belt. ... Eureka WhirlWind 4381 Upright Vacuum

How to change the belt on a eureka vacuum model


... Eureka Smartvac 4870 Bagged Upright Vacuum

Changeing belt how do you install a new belt? I have an Eureka, The Boss, bagless, upright. The brush is hardly rotating. I think it could be the belt but i cannot open the vacumm to check it. How can I fix this?


... Vacuums

Eureka 'the boss' lite model 7605 - no power


... Vacuums

How to change belt 4870MZ Eureka Smart Boss Vacuum


... Vacuums

I have a Eureka True Hepa WhirlWind 12AMPS,Model #4380 type A-3.What type of belt do I buy for this model?


Http://www4.dealtime.com/xDN-vacuum_cleaner_accessories ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1106 seconds