Having problems with your Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum ?

How to change belt on eureka whirlwind; what tool do I need


Answers :

You will first need to remove the hood to gain access to the belt and brush roller. Turn the machine upside down, place the handle on the floor and the base on a counter. You will find several screws that hold on the hood, remove them. Turn the machine back to the upright position and remove the hood. On the right hand side,if your looking the front you will find where the belt goes. At the back you will find a silver shaft sticking out, put the new belt on there first. Then put the brush roller through the belt so it is in the carved out section of the brush roller. Then grab the brush roller by each end and stretch the belt till the brush roller fits back into the base. Turn the brush roller 3 compleat turns backwards and 3 forward to seat the belt in the proper position.
\015\012Then put back on the hood.
Repair Help & Product Troubleshooting for Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

How to change belt on eureka whirlwind; what tool do I need


You will first need to remove the hood to gain access to the belt and brush roller. Turn the machine upside down, place the handle on the floor and the base on a counter. You will find several screws that hold on the hood, remove them. Turn the machi ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

MY VACUUM ISN'T PULLING AS STRONG AS IT USED TO SO I THINK IT NEEDS A NEW BELT. I CAN'T FIND THE MANUEL ON IT SO I NEED SOME INSTRUCTIONS ON HOW TO CHANGE THE BELT. I DON'T WANT TO BREAK MY VAC. CAN SOME ONE PLEASE INSTRUCT ME ON HOW I SHOULD CHANGE THE BELT PLEASE. TYPE VAC: EUREKA THE BOSS WHIRLWIND LITE CYCLONIC POWER CANISTER TYPE VAC. THE HANDLE IS DETACHABLE TO CLEAN IN THE CORNER WITH A SMALL EXTENSION.


You can get Eureka replacement belts here:Eureka Vacuum Betls ... Vacuums

Belt location i have a eureka upright the boss whirlwind lite and i need to change the belt. I have no clue where to find it. Need help with this


If you torn the macine over, at the bottom of the sweeper you will see the belt on on side. You have to take the bottom part apart and remove the brushes to replace the belt. I hope this helps. ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

Belt?! hello, I need to change the Eureka Oxygen Canister Air Driven Upholstery Tool's Belt (model 5860Avh), but I don't know which one to get? any help please? Best, Pierre.


You will probably have to order it online. ... Vacuums

Change belt How do I change the belt Eureka whirlwind 4480. As I look under the house I think I see one screw on each side down in about 3/4 inch. Are those the screws to remove and are there only two you have to remove?


... Eureka WhirlWind 4381 Upright Vacuum

Changing belt - Eureka Whirlwind 5740


I tried the website for manuals but no luck. I called the toll-free # 1-800-282-2886 and got a rep right away. I gave him the model and s/n (lower bottom on the back side) and he walked me thru it. For the model I have, there are 3 screws to remov ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

How to change belt on Eureka Whirlwind


On the top cover, there are holes at the front on both sides, there is a screw on each side in one of the holes. Take the out, and the cover should come off, then you can get to the brush roll and belt. ... Eureka WhirlWind 4381 Upright Vacuum

Need to replace belt on Eureka Powerline 12.0 vac. Screws look like Torx head or something on bottom of vac. Are those the screws that need to come out for changing? If so, what size do I need?


No, do not remove the torx head screws for a belt change. If there are any screws that need to be removed for the belt change, they will be phillips head. What is model # of vac?? ... Eureka Vacuums

Need to change belt. Need instructions. - Eureka 5859ASZ Bagless Upright Vacuum


... Eureka 5859ASZ Bagless Upright Vacuum

How to change the belt on eureka 3281az - Eureka WhirlWind 4381 Upright Vacuum


... Eureka WhirlWind 4381 Upright Vacuum

Change belt on eureka clean living 3281bz - Eureka WhirlWind 4381 Upright Vacuum


... Eureka WhirlWind 4381 Upright Vacuum

Eureka whirlwind+ Is there a belt!? Smell hot like burning rubber...can't locate a belt to change?


It's a little tricky but here's how you get to the belt:Once you have removed the housing and the roller, turn the vacuum so that you are facing the pin the turns. Pull the belt to the back of the un ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

HOW DO I CHANGE THE BELT ON MY EUREKA WHIRLWIND MODEL 3272


... Vacuums

How do I change belt for Eureka Whirlwind Lite "Boss" model 450 A


Remove the 4 screws on the yellow top of the vacuum. The yellow plate will pop up exposing the belt and roller. ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

Weird noise i have a eureka the boss and i am getting a weird noise figured bag was full needed to change it so i did. Noise persisted so i checked make sure nothing was caught in the brushes. I even checked the belt it was fine replaced with a new one.Still the noise is there help me I am out of what else to check.


Squealing ... Vacuums

Change the belt on Model#4481 vaccume - Eureka Whirlwind 4481 Upright Vacuum


... Eureka Whirlwind 4481 Upright Vacuum

How do I change the belt on my eureka whirlwind plus vacuum?


If you go to this URL you can see videos on read articles on changing the belt.\015\012Please make sure it is the correct model number:\015\012\015\012http://www.ereplacementparts.com/eureka-3277avz-upright-vacuum-parts-c-108750_108773_109147.h ... Vacuums

I live at zip code 24060 and I need a new belt for my Eureka Whirlwind. Where can buy this?


You can get them at Walmart. \015\012Look on the nameplate and it will tell you which belt too buy\015\012(Probably a "U" belt) ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

Just need to know how to change the belt on my Eureka AirSpeed Gold Bagless Vacuum


... Eureka Vacuums

Change belt on eureka whirlwind vacuum model 4689


... Eureka 4689 Upright Vacuum

I need help changing belt on my Eureka Optima


If you're not familiar with how the vacuum is put together, taking it apart can be a real pain. Thankfully, most of the screws on the unit are the same size and type. For the ones you need to remove, a #2 Phillips should do the trick.Un ... Eureka 431A Optima Bagless Upright Vacuum

Help hi i have a eureka bravo model #9270 and i need instructions how to change the belt, i took out twoscrews it looks like the top comes off but it doesn't come off all the way.


The handle should be down and the top may have a tab on both sides to pry out with screwdriver. lay handle down and turn machine over. look closely around base between cover and there should be a tab to push on and cover comes off. ... Eureka Vacuums

I changed the belt on a Eureka WhirlWind superlite, all was well but I can't seem to find where this white piece of plastic approx.2" and less than 1/2" wide and there is a copper like V shaped clip, I was hoping maybe you's had a diagram or something showing where these go. Much Appreciated


Http://www.geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=552328\015\012Generic problem for all Vacuums\015\012I changed the belt on\015\012Posted by hiphoppy69 on Apr 28 ... Vacuums

Bought at walmart - don't carry the Eureka Boss Whirlwind now and I need replacement belts


Find a vacuum repair store in the yellow pages, these are common items so they will have them in stock. ... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

I can't figure out how to change the belt on my Eureka whirlwind Model #5740 vacuum


Remove 4 screws on top and lift cover. ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0656 seconds