Having problems with your Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum ?

Location thermal cut-off swith for eureka AS1100

Answers :

Repair Help & Product Troubleshooting for Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Location thermal cut-off swith for eureka AS1100

... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

Possible reset on Thermal Cut-Off

This is not really expert advise but I have a vaccuum with hepa filters and if the filters get dirty My vaccuum acts like your what you are describing. ... Eureka Vacuums

Thermal senser on the side of the vacuum motor there is a little thermal senser that has rust all inside of it ,my ? is will that cause the motor to shut down ,could the rust in the senser causing it to cut off ,cause the vacuum runs well then cuts off

If it is going bad, it will cause the motor to shut down, replace it then you will know if that is the problem or a problem with the motor itself. ... Vacuums

Why does my dyson dc04 work for about 5 mins then cut out the wire on my dyson 04 needs replacin but i cant get the casing off. My DC04 cuts out after abou 5 minutes use. I think there may be a thermal cut-out somewhere?

Thermal cut out in coils of motor,you have not been keeping filers clea,I THINK.\015\012motor is avaliable ... Vacuums

Dyson DC07 My DC07 cuts out after 5 mins and I want to replace the thermal cutout. I have cleaned it thoroughly, including the cyclones but it still cuts out. How does the plastic moulding around the motor dismantle? I have started by removing the 4 torx screws but the upper grey housing does not want to detach and I am worried about breaking the plastic. Appreciate any advice.

Try this page: -http://www.fixya.com/support/t192124-overheating_dyson_dc07Regards Gualo ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

Thermal switch on eureka vacuum 4870 - Eureka Smartvac 4870 Bagged Upright Vacuum

... Eureka Smartvac 4870 Bagged Upright Vacuum

Reset button on thermal cut-off

... Vacuums

Eureka sanitaire SC412 thermal reset

Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=658043\015\012Generic problem for all Vacuums\015\012Eureka sanitaire SC412 thermal reset\015\012 ... Vacuums

Eureka Ultra Smart Vac bag overfilled, and it cut out

... Eureka Smartvac 4870 Bagged Upright Vacuum

Eureka Capture won't turn on after thermal cutoff

Return it for an exchange, under warranty ... Vacuums

Where is the thermal protector swith in my 360 Swivel vacuum model 116.29219

... Kenmore Vacuums

Belt location i have a eureka upright the boss whirlwind lite and i need to change the belt. I have no clue where to find it. Need help with this

If you torn the macine over, at the bottom of the sweeper you will see the belt on on side. You have to take the bottom part apart and remove the brushes to replace the belt. I hope this helps. ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

Eureka Boss 4870gz shuts off (thermal protector) after 2 or 3 min

Wiggle the cord while running the vac. if it cuts off from that, then you most likely have a bad switch or cord. if the motor was bad, you would smell it. it smells aweful. ... Eureka Smartvac 4870 Bagged Upright Vacuum

I built a new house nearly a year ago but didn't move in until recently. The Nutone central vacum system doesn't have much suction. I've tried different things but am afraid there is a break or breaks in the system. My question is how can breaks or joints that come a part in the suction system be located so I will know where to cut into the wall.

Hi,\015\012\015\012Here I am giving link of manual which shows how to install the your gadget.\015\012http://www.retrevo.com/support/ ... Broan-NuTone VX475 Bagged Central System Vacuum

How do you change the belt on a Eureka Altima and where is it located.

Hi, \012\012Just to get to the belt, you will have to remove 2 or 3 screws. All of which are located in the top cover. one on the left and right of the machine as your looking at it. The third screw if it is there, will be between the bod ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Where is the belt located - Eureka 3276AZ Pet Lover Bagless Upright Vacuum

... Eureka 3276AZ Pet Lover Bagless Upright Vacuum

Our Electrolux Z432A Vitality vacuum cleaner thermal cut off switch is way too sensitive. Can it easily be adjusted or bought and replaced?

... Electrolux Vacuums

There is no suction when the Eureka model 7685 is turned on. Is there an Air filter? If so, where is it located? The belt turns slowly when the vacuum is turned on. Is that normal?

No you vacuum tub is clogged. Shut off machine and remove hose where attachments go. Use a long handled kitchen appliance like a spaghetti stir to work the jam back and forth. You will be amazed at what comes out. Then remov ... Eureka 4874 Bagged Upright Vacuum

Eureka enviro vac 3041bz son sucked a sock up in the vacuum, its turned off. I removed the sock from the tube. Now it wont turn back on. Is there a reset switch and if so where is it located

... Eureka 411A Upright Vacuum

Eureka 4467AV overheats and shuts down after about 3 or 4 minutes of operation. I pulled all the filters to assure no blocked air flow. I assume the motor is not getting enough cooling air but i can't figure out why. checked bag for blockages as well as hoses. could the thermal protection have gone bad?

... Eureka 4467AV Upright Vacuum

Cut off while vacuuming - Eureka 4700A Maxima Bagless Upright Vacuum

If it went dead, and restarted after it cooled off, then check for a clog in the hose or the dirt inlet by the brush roll. If it won't turn on, you could have a bad switch, cord, motor or a bad electrical connection. ... Eureka 4700A Maxima Bagless Upright Vacuum

My EUREKA MAXIMA vacuum cleaner keeps cutting off

... Eureka Vacuums

Thermal fuse keeps cutting in, Is there any way to check motor before replacing it. on a dyson upright cyclone model

... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0489 seconds