Having problems with your Eureka Whirlwind LiteSpeed 5843 Upright Vacuum ?

Belt keeps slipping off need to check the correct belt number and what can i do


Answers :

What does it slip off of, the brush or the motor? Are you sure that it is in correctly, as there are usually 2 ways of putting the belt on. If put on correctly, it should not contact any part of the vacuum except the motor shaft and the brush. Also check check there is not a buildup of hair, etc. where the belt goes around the brush. I would try turning the brush by hand and see if anything is interfering with the path of the belt. There is always a chance that some part of your vacuum has broken or malfunctioned and is touching the belt and making it come off. Also, make sure that the brush is correctly installed.
\015\012
\015\012The tension on the belt should be pretty high so that it is hard to pull out of place. If not, you could have the wrong belt. I believe that this takes a type "U" belt if that is any help. Hope this helps and good luck!
Get the EXT-U belt.
Repair Help & Product Troubleshooting for Eureka Whirlwind LiteSpeed 5843 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Belt keeps slipping off need to check the correct belt number and what can i do


What does it slip off of, the brush or the motor? Are you sure that it is in correctly, as there are usually 2 ways of putting the belt on. If put on correctly, it should not contact any part of the vacuum except the motor shaft and the brush. Als ... Eureka Whirlwind LiteSpeed 5843 Upright Vacuum

OUR DYSON 07 SWEEPER HAS VERY LITTLE Vacuum, have cleaned all filters and hoses, on line troubleshooting has said to check soleplate being on correctly, we have done this, still does not have good vacuum, belts are covered by a housing, the video that shows the changing of the belt is not the same, I need to know how to remove the cover to check both belts and any help in gaining the vacuum


This video shows you everything you need to know ... Vacuums

Windtunnel belt I have a new Hoover Windtunnel canister. The belt keeps coming off. It happened a couple weeks ago (several times after putting the belt back on) so I assumed I might need a new belt as it might have dried out at the store. I ordered new belts and today I used it for about an hour and the belt came off again, twice. There doesn't seem to be anything to hold the belt on the stem as it seems to slip off. I have tried it centered, to the left and to the right....can you help. I am v


I've successfully used a compatible belt - Royal 104425001 .It's still new, but for the time being at least - it works. ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina


Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum

How can determine when it's time to replace the drive belt on my Bissel Power Steamer? Is there a certain number of hours of usage that I need to keep track of or does the belt replacement depend on the type of carpet I'm cleaning? Thanks, Jim


Usually, replacement is needed when the brush no longer runs or is intermittent. Check the brush bearings and for debris build-up whenever the belt is changed. Good luck! ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

I have a hoover spinscrub carpet cleaner model F7221-900 I need to download a user manual for.But hoover website tells me they can,t find this model number. I have checked # several times and it is correct. whats up?


I just needed to clean the brushes I finally just found the clips on each side of the brush roller and pressed in towards center and was able to pull brushes out. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

My girlfriend has a Hoover upright vacuum, Mdl. # U4645-930. I need a belt for the brush and a new bulb and am having trouble finding the correct part numbers so I can pick one up locally. Can you help?


I checked with Hoover and they said the part number for the belt is #38528040, for the bulb #27313101, and they also included a part number for something called an agitator #48414081. Not sure if this is required to replace one of the other parts. ... Hoover Windtunnel Turbo Power U4645-930 Vacuum

My Eureka Maxima 4704 pink vacuum is really squalling .. its so loud you need ear plugs .. we just got the thing Christmas .. and has been used under normal conditions..we keep the filter clean and even recently washed it and let it dry for 12 hrs to see if that was the problem but it wasn't what else could be the problem ... I do not think that the belt is slipping because I can't smell rubber burning ...IM STUMPED


... Vacuums

Need help with Hoover S3765-040 WindTunnel Electronic Bagless Canister Vacuum. The belt that rotates the brush keeps slipping off. what to do?


The belt could be stretched and that could be causing the slip. Or you could have the wrong belt if you've replaced it recently ... Vacuums

I have replaced the correct blets and lined themupon the pulley but the v- belts keeps slipping off the pulley and than the brush will not spin


The pulley is not adjusted properly so the belt is slipping.\015\012There is a small wheel/pulley that keeps the v-belt tight and it is stuck.\015\012to adjust the pulley try this system. move the carpet height control lever and the brus ... Hoover U5780-900 Windtunnel Cyclonic Bagless UprightVacuum

Need to check , belt , donot where to check,on


You can get hoover replacement belts and manuals here:Hoover Vacuum Belts ... Vacuums

Belt slipping Belt slips off and rubs causing burning smell from the belt over heating. Of course this puts an indent into the belt and has to be replaced. How do I keep the belt from slipping off? I see no place for a belt adjustment. Which I know would eliminate the problem. Really aggravating to have to replace belt only after two uses.


On the roller/brush where the belt sits if that is scarred up or grooved out that will cause the belt to slip if you can fix roller try but i suggest new roller ... Hoover Company Wind Tunnel U53019 Upright Vacuum

New Eureka vacuum cleaner belt keeps slipping off


You may have a bad brush roll, part #61250-1, or the base itself has a problem and isn't letting the brush roll sit straight so it can be in alignment. ... Vacuums

Eureka 5843 belt keeps slipping off of drive spindle.


Tough one. Typically the only 2 things that the belt contacts is the motor drive spindle and the brush roller. Anything else would only be there to protect the belt from debris. Can you turn the brush by hand and see why the belt is coming off? I ... Eureka Whirlwind LiteSpeed 5843 Upright Vacuum

Need to find the belt for the brush. Every sight leads me to drive belts and I dont need that. I need a model number prefferably


Unscrew both bolts that are in plain sight on top of vac above the brush, then remove housing and belt is right there ... Dyson DC07 Bagless Upright Cyclonic Vacuum

I keep replacing the belt and keeps melting and breaks. what do i need to do? everything else is working, the little piece of metal that hooks on the belt gets too hot and melt the belt


I think your talking about the motor spindel,,(the little metal bit?) if the motor is that hot its going to burn out soon, check that the brush is free to turn if its tight free it off its full of grit or fluff also check that the motor turns freely ... Dirt Devil M084600 Dynamite Bagless Upright Vacuum

Were can I order a belt for a HOOVER MODEL U4423 ? The belt number needed is # 49258AG


Go here > http://hoover.com/search/?q=49258ag&x=17&y=8 for your belt ... Hoover Vacuums

Hi my proheat bissell 7901 stopped pumping water to the floor, but it pumps water from the hand hose. I read the manual and followed how to check belt and the flat belt on right side of shampooer is fine and I turned on and it turns and so do the brushes at the bottom of the machine. I was reading online and I guess there's two belts on this machine? where can I find the other belt to see if it needs replacing. I guess it's a ribbed belt? that is the water pump belt?


Just taken ours apart with the same problem... found it was caused by the 2 halves of the main casing coming apart in the area where the upright pedal release is. I found this to be due to the upper casing having broken in 2 places - the bottom of th ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Hoover bagless cannister 3765 - belt on power head slips off spindle. bought new belts - same problem. is this a design problem or can it be fixed? I don't want to take it to a repair shop 100 miles away and have them just put on a new belt. saw idea of smaller belt - what number? couldn't find suggested royal 104425001 belt.


I would not recommend a smaller belt. You will only wear the motor. This model series power nozzle needs to have a metal clip installed near the belt on the brush roller housing. I know that most of them left the factory without it. Remove the cover ... Hoover S3765-040 WindTunnel Bagless Canister Vacuum

Replaced the belts on Saturday with belts that were purchased in 2003 but never needed. It is Monday and the small belt has already cracked and separated from the center fiberglass or whatever the band is made of. Is there any way to keep these belts from drying out in Alaska?


Hi Alaska,You can put a small amount of vaseline or a tiny bit of any oil on the back and ONLY the back of the belt Do not get any on the sides or inside of belt. Please be sparing with the oil.You can also put these in a zip lock b ... Vacuums

I have a Hoover power max self propelled vacuum. The belt that goes to the self propelled part keeps slipping off. I've had the belt replaced, but the problem persists. What can be wrong? I've taken it to a Sew N Vac repair, but all he did was replace the belt again. And it still has the same problem.


I can guess of one problembelt gets removed when motor is running right?am assuming that belt is fit tightly and fits correctly when motor is in restif so then ur motor is not running at a proper speed which can be a pos ... Vacuums

The belt on my used Eureka Boss 5857 upright slips off the end of the motor shaft every time the vacuum is used. When I turn the brush roll slowly by hand, the belt walks toward the end of the shaft. It looks like there was a plastic projection from the base that snapped off, and maybe that plastic piece used to block the belt from falling off. Do I need to try to reconstruct that plastic piece, or is something else wrong?


... Eureka 5856BVZ Boss Bagless Upright Cyclonic Vacuum

I need a drive belt for Shark vac. Model number UV210BS---The small belt that drives the larger belt for the beater .


... Vacuums

I need to replace the belt on my hoover fusion plus upright vac. But I cannot find what belt it takes. the number on the belt is worn off


Hello : \015\012\015\0121:Unplug your Hoover vacuum. Turn the vacuum up-side-down and place the motor and vacuum portion on a counter top with the handle hanging down toward the floor. This makes it easy to work on the underside of ... Hoover Fusion Plus Cyclonic Upright Vacuum Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0754 seconds