Having problems with your Eureka WhirlWind Litespeed 5844 Upright Vacuum ?

Eureka 4D. Brush turns but not alot of suction. dust bunnies build up inside the hose at the bottom and at the dust brush connection. Seems to be very hot. ?????

Answers :

Try cleaning the filters
Repair Help & Product Troubleshooting for Eureka WhirlWind Litespeed 5844 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Eureka 4D. Brush turns but not alot of suction. dust bunnies build up inside the hose at the bottom and at the dust brush connection. Seems to be very hot. ?????

Try cleaning the filters ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

I have a DC07 and the brush wasn't rotating and I had no suction at the brush but perfect suction through the hose. I noticed a large build up of dog hair around the brush so I took off the cover plate and removed all the hair, cleaned inside the floor/brush housing and cleaned out the hose. I also cleaned the filter and removed the other air access cover and made sure that they were clear. I put everything back and the brush still doesn't turn and there is still no suction through the bottom

Hi and welcome to FixYa. I am Kelly. \015\012\015\012Here is a link that can assist you in your quest for the missing suction: \015\012\015\012 ... Dyson DC07 Bagless Upright Cyclonic Vacuum

We have a beam Serenity plus home vacuum system and there is no longer sucks. I removed the dirt from the bottom plastic container, but I also notice a sack or bag connected to the unit when I removed the bottom container and inside that sack there appears to be lots of dust. How do I access that and remove that dust without damaging the unit. I don't know how to do that

Hello. Let's begin by getting that dust and dirt out of your permanent filter. To do this, get a big clear plastic bag and pull it up aroung your canister, with the dirt receptacle removed. Then Grasp the sewn in weight inside of the filter and sh ... Beam Industries 2900 Serenity Plus Central System Vacuum

The hose on my Samsung 9048R is torn partly from the swivel base. The main problem is that the carpet attachment with the beater bar will not operate now. My brother checked the connectivity at both ends of the hose and there is juice at the bottom swivel part but at the other end of the hose where the carpet wand plugs in it is dead. is there any way to fix this? How does the wire go up through the hose? I have looked around on the internet and it would seem that the entire hose assembly is

... Samsung Quiet Storm 9048R Bagged Canister Vacuum

ShopVac pump The waterhose connection is up high. The only way to get the water up to the level of the hose is to continually hold down the on button due to the automatic shut off after it fills to a certain level. On the bottom of the filter there is a hole. I am thinking there should be a small hose of some sort to put into that hole that would then lead up to the level of the water hose. Concept makes sense to me. But in the meantime, good old duct tape seems to have done the trick. Not exact

Hey thats great whatever works its what makes america great ... Shop Vac 584-06-00 Canister Wet/Dry Vacuum

I have used my Steam Vac for carpeting, but until today, had never tried cleaning upholstery with the spin-scrub brush. I spent a miserable afternoon trying to control the spray, which seemed to go everywhere AROUND the furniture, but not ON the furniture! Additionally, I never did get the water into the recovery tank, despite many attempts to connect and re-connect the hoses and recovery tank/lid.

I can sympathize. My vac came with two handheld attachments. I have better luck with the handheld attachment that doesn't have the spin-scrub pads. To keep the water from going all over the place, you need to keep the part the you hold only about 1 ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I bout this vacume in mid December 07 and about February-March it started not picking up the dust on the floor. So in early April I bout a new filter and it still wasn't picking up the way it had in the beginning. I've taken it a part several times and cleaned it out with it being plugged at the bottom hose with dust bunnies. Well I just took it back to Walmart where I purchased it and I failed to keep the reciet they could not do any thing about the sweeper. I went back to the sweepers and re

Pull the hose out of the holder, is there suction there. If not, then there is a clog in the hose. If there is suction, then check the dirt outlet by the brush roll. Also if the belt is slipping, it may appear to not have as much suction, belts wi ... Dirt Devil Vacuums

I have a Panasonic MC-E3011 and it won't ****. I have checked all the pipes from the beater to the inlet at the dust bag, and they are both clear, pluss the air comming out of the vent at the bottom of the upright (above the beater) casing seems abnormally hot. I have allso checked the the belt and beater bar and they are functioning A1 OK.

... Panasonic MC-V7395 Vacuum

This is a new machine I got for Christmas. All of the dirt is staying in the area where the brushes are and then falls out when you turn off the machine. I have checked all connections and the hoses seem to be clear. All filters have been cleaned and there is not dirt trapped that I can see.

... LG Electronics Kompressor Pet Care Upright Vacuum Cleaner LUV200R

Clogged hose A makeup brush (about 3.5 inches long) was sucked up through the vacuum hose. It won't come back through the same way it came in because the bristles in the brush are expanded. We can see the brush on the side of the hose that connects to the canister but can't get it around the bend of the 360 part of the hose... is there any way to take the hose apart more?

... Kenmore 25512/ 25513 Progressive Canister Vacuum

Water leaking from bottom and hose not connected

The hose just pushes on. You will have to take the top cover off to rehook up the hoses. There are scres on the bottom, then where the dirty water tank sits, there tabs that you have to unhook, then the cover will come off. Note: the filter inside ... Hoover V1 SteamVac SpinScrub Vacuum

When I try to disconnect the hose in order to use the hand held hose with an attachment, the dust from the bottom flies into the air. How does this opening get blocked off to ensure the dust enters through the attachment and not the bottom?

It is a matter of Physics. It seems like you have it running when you change the hose. ?? That's a no-no.Basically you will have o take it apart until you know how it works or wont work ... Bissell Vacuums

Have a canister model Lux5500-ser#F35365B and power nozzle number N115Q-problem: The power nozzel does not stay completely connected to the hose-there seems to be some slipage where the hose connects to the nozzel-preventing a solid connection and the unit from working properly. I tried to tighten the connections on the nozzel, but this has not helped

... Electrolux Guardian Bagged Canister Vacuum

I have a Miele Vacuum cleaner MedicAir 5000 Plus. Recently the Dust Bag Indicator bar is full during normal cleaning and consequently the suction power is much less. I replaced the dust bag, engine pre-filter and Hepa filter but no change. When i remove the hose, the Indicator is normal, but when i attach the hose, wand, head, the indicator is full. I checked the hose, wand, head but can't see any blockage and when i blow with my mouth it seems fine. Can anybody help? thanks!

... Miele Vacuums

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?

If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

I was checking the hose that attaches to the bottom circular peice and I lost the hose inside. How do I take the bottom off to reattach the hose?

Steps to take off the bottom are listed on page 19 of the manual HERE ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I cleaned out my brush in the bottom front, cleaned out the small tubing going into the canister, and the canister itself. I also changed the filter.I snapped everything back into place, but Since then, it doesn't seem to have any suction and there seems to be a space between the canister and the bottom of the vacumm where the canister sits. At that area, you can feel air coming out when trying to vacumm and it just doesn't pick up, it seems to be just blowing stuff around.

You need to really look at it some thing is out of line you shooed not have\015\012any spaces in the top or bottom\015\012pull the canister back out and look at the pins that you lined up with the\015\012to ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

No Problems with suction on hoses, however brush area it seems to lose powe, and has little suction r

We had a similar problem with ours and had to finally take it to the repair shop. They informed us that we needed to replace our clutch and that you needed to do that every 2-3 years. It cost less than $100 and has been well worth it. ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

The solution has stopped going out the hose. The hose seems to be deep inside the machine. How do I get to it to unclog it?

The hose unhooks by the motor. But it could be the valve in the hose head. Maybe this picture will help:\015\012\015\012 ... Hoover F5866-900 SteamVac Deluxe Wet/Dry Vacuum

My DC17 is only a few months old, but I've already had to clean the filter. Since I reassembled everything, I'm finding chunks of carpet fiber and dog fur on top of the filter inside the filter container. Iam getting slightly less suction from the floor assembly as well. I've checked the hoses, brush, and brushed out the inside of the plastic container, but hasn't helped. Ideas??

Everyone needs to own an air compressor,\015\012if you own a bagless vacuum\015\012\015\012You blow it out every other time you use it.\015\012\015\012Without compressed air, all vacuums will just\015\012basically ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.

Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

No suction I have new belts. Everything is clean. No clogs. When I turn it on it smells like rubber , the brush doesnt spin. Everything seems to be free flowing.. Roller brush isnt stuck on the ends. Took off hose to make sure no clogs anywhere. There is not even suction thru the hose with the handle in upright position.

Generally, the problem is that the belt is not running the brushes.  This is caused by one of the following:\015\012\015\012\015\012beater brush is jammed.  This is either an object stuck in the brush or im ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

The hose works great, but the head of the vaccuum does not pick up anything !!! I checked every opening that may have been clogged, but nothing came up. When I hold my hand under the brush/roller, it seems to be putting out more air than intaking air. Particles "dance" on the carpet, but don't get "sucked up" into the vaccuum ? I have had the vaccuum only 1 year, so the brushes should not be a problem. I changed the bag, and checked the belt. The belt and brushes seem to be OK. ?

Hi there,Uprights are notorious for debris forming clogs when changing direction. The 90 degree turn where the base suction goes up. Have a closer look . You may need to pull the base plate off to access the blockage.Best reg ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Help hi there. i have a hoover savvy u8172-900 vaccum. the hose has great suction, but there is limited suction on the main unit and the brush does not spin when i try to use the product. we have cleared the brush of any debris and have also installed a new bag. a few days ago, we disconnected the hose to make sure there was not any foreign bodies stuck in the unit...nothing seems to help. any advise?

As the hose fits into the base (if i am correct) the power at the base should be fine, make sure the base is clean and free from blockage,\015\012you say the brush doesn't spin, has the belt broken, if so replace it, (very cheap) and only a couple of ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

My electrolux oxygen canister cuts on and off. I have to open and close the vacuum, or take the base of the hose off and then re-insert. I have to do all these things before it will start up again. I sometimes shake the hose around, then it will come back on. If I try to dust with the dust brush (like a lamp shade or shelf) and the suction pulls against the object, the vacuum goes off for awhile. Sometimes I'll have to reset the vacuum by unplugging the electric cord. I never get to finis

Maybe you should have taken it back to that shop, it appartently isn't fixed. I would have replace that board, don't believe in modifing, you usually end up with other problems, like you have. One thing to check is maybe you have a partial clog in ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 2.0170 seconds