Having problems with your Eureka WhirlWind Litespeed 5844 Upright Vacuum ?

There is a metal post that spins and rotates the belt at the opposite side from the brush. the removable wheel that holds the belt onto the metal pin is missing. how can i buy that part? eureka whirlwind lightspeed #5844


Answers :

Vacuum 24x7.com, they should have the parts
Repair Help & Product Troubleshooting for Eureka WhirlWind Litespeed 5844 Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

There is a metal post that spins and rotates the belt at the opposite side from the brush. the removable wheel that holds the belt onto the metal pin is missing. how can i buy that part? eureka whirlwind lightspeed #5844


Vacuum 24x7.com, they should have the parts ... Eureka WhirlWind Litespeed 5844 Upright Vacuum

Hoover Wind Tunnel 7500 Brush not Turning. I have replaced the Brush and the belt. The problem does not seem to be either to me. I believe might be a missing part. The place were the belt hooks on is a metal pole which never seems to grip the belt well. In fact it seems loose most of the time and slips on the brush, causing the belt to eventually burn up. Could there be a missing plastic or rubber piece meant to hold the belt taught  on the metal pole?


Check the Idler Pulley part Number 43241004 (Item 13 in the IPB)http://64.49.205.183/v/u6451900.pdf ... Vacuums

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?


Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum

I have a eureka surface max 300, i saw smoke come out of my vacuum i seen that the belt was broke every time i change belt i run it on it snaps every time ive put 3 new ones and each one break right when i start it it looks like the metal piece is burning it is there a piece missing?? what am i doing wrong?? ugh i just purchased it couple of months agoo not even older then 6 months .. what do i do?


... Eureka Capture Upright Vacuum Vacuum

Hoover model u5146900 the belt drive is bare metal wears out the belt quickly is there a part that fits over the pin?


The belt drive shaft does not actually wear out the belt unless it has a burr on it, however frequent use does.It should be kept clean and polished with no residual dirt ir burnd rubber. On a department store brand vac you should expect to chan ... Hoover U5144900 / U5146900 / U5147900 Tempo Bagged Upright Vacuum

Missing Part(s) for Eureka Whirlwind 4496


Go directly to eureka.com,if that don't work you can call all-type vacuum and janitorial supply.314-275-8006 ask for lisa.or go to geyser.com he might be able to get it for you ... Eureka Whirlwind 4496 Bagless Upright Cyclonic Vacuum

Whats the part number for belt - Eureka WhirlWind 4381 Upright Vacuum


... Eureka WhirlWind 4381 Upright Vacuum

Eureka TRUE HEPA Whirlwind Bagless same problem seems...roller just stopped...took everything apart and turned it on just in time to see belt melt...I was able to get the end caps off both sides at first and now can't seem to get the one side. Really love this vacuum! Don't want to have to part with it!


If you are able to remove one end cap, the brush roller shaft can be removed and the other bearing is exposed for examination and removal of the hair that probably is clogging it. After cleaning and reassembly the brush roller should rotate freely. C ... Eureka 2961AVZ Bagless Upright Vacuum

I live at zip code 24060 and I need a new belt for my Eureka Whirlwind. Where can buy this?


You can get them at Walmart. \015\012Look on the nameplate and it will tell you which belt too buy\015\012(Probably a "U" belt) ... Eureka Whirlwind Litespeed 5840 Bagless Upright Cyclonic Vacuum

DC 17 animal, axle roller that acts as a belt tensioner is shot, including the plastic mount that it sets in, (poor design) that wore down when the roller froze up. Where can I get just this part without having to buy the whole brush head assembly? Do they have one that is metal? Not the roller the mount for it>


I've had this stupid problem and my $500 dollar vacume has been broke for months so today after I spent hours on hold at dyson and talking to sears and everybody else under the sun and they say part doesn't exist pretty much, so finally I talk to a d ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a Eureka True Hepa WhirlWind 12AMPS,Model #4380 type A-3.What type of belt do I buy for this model?


Http://www4.dealtime.com/xDN-vacuum_cleaner_accessories ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

I have a Hoover Windtunnel U5472-940. The belt broke so I replaced it. Immediately the next one broke. The belt goes around the brush cylinder and a metal post. I think there is supposed to be something on the metal post to protect the belt but I can't tell from the owner's manual. I also can't find out if this is a part that can be replaced. I've only had the vacuum about a year and a half. Thanks


You may have something in your brush bearing that does not allow the brush to turn easily thus stretching the belt. Chris ... Hoover U6455-900 WindTunnel Vacuum

I was replacing the belt on my Eureka Smartvac 4870 and one of the felt gaskets (or part of it) popped out. I thought I put it in correctly, but the first I used it after replacing the belt, the gasket got mangled by the brush. I'm wondering how important it is to get fixed; is it a part I can pick up anywhere and fix myself? Thanks for the help.


I'm no expert but if you mean the felt on the roller, you have to replace the roller (expensive,esp. for such a minor part). So. I found some felt with adhesive in the craft section at Wal-Mart, trimmed it to fit and done deal. Felt reduces friction. ... Eureka Smartvac 4870 Bagged Upright Vacuum

What size belt does a eureka whirlwind take - Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum


Hi,\015\012\015\012Your Eureka Whirlwind 4388 takes Eureka Style "U" Belts, Part number 54312. \015\012\015\012Here's a direct link back to that belt on our website if you need to purchase one:\015\012 ... Eureka Whirlwind 4388 Bagless Upright Cyclonic Vacuum

Eureka whirlwind lite which belt? - Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum


... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

INSTRUCTION MANUAL FOR EUREKA LIGHTSPEED 100 - Eureka 2 Type Dcf4-Dcf18 Upright Vacuum Cleaner Hepa Pleated Washable Filter W/activated Charcoal Whirlwind Mighty Mite Maxima Boss Power Plus Pet Pal Lightforce 300 Lightspeed 100 General Electric Ge 63073 4700 5500


... Eureka 2 Type Dcf4-Dcf18 Upright Vacuum Cleaner Hepa Pleated Washable Filter W/activated Charcoal Whirlwind Mighty Mite Maxima Boss Power Plus Pet Pal Lightforce 300 Lightspeed 100 General Electric Ge 63073 4700 5500

Is there any way to repair or replace the belt GUIDE on the inside of the belt compartment of a '97 Hoover Wind Tunnel (not self-propelled)? It became twisted when a belt broke and now the belt rubs against it and sounds really weird, and I'm sure new belts will continue to break.. This guide is a long piece of molded material (part of the compartent wall) to keep the belt from coming off the pulley. It also had a sort of metal clip on it. It was loose and I took it off because of the way the pa


Honestly you should take it to a vac.shop they can fix any vac. ... Windsor SR12 Sensor Bagged Upright Vacuum

On my Eureka Model 1759A (from mid-1980s), the plastic catch that holds the two parts of the metal body together has broken. I would like to replace the part of the catch that attaches to the top (the part with the lip on it), but I can't find the part online ... or even a drawing. Where can I get this part ? ? ? HELP ! ! !


This latch is riveted to the body. If you are lucky you may find an old Eureka warranty/ repair center with one on the shelf, or another canister for parts. That will be your best hope. ... Vacuums

Hello, I have a Kenmore Progressive Canister Vacuum 116.20912006. It won't turn on. On the hose assembly, the end where the hose swivel is, there are 4 metal pins that plug into the canister. One of the pins looks like it broke off. There are only three pins remaining. I assume there should be four pins as there are four holes. Is this the problem and is it fixable? The vacuum is from 2002 so I am not sure a replacement part is even available and at what price. Thank you. Susan susan.eng@


Hi Susan, if the pin has broken off you can do one of two things, first, would be to find a local vacuum repair shop and take it there for them to look at. they may be able to look at the hose and fix it for you pretty cheaply. what ... Kenmore Progressive 20912 Bagged Canister Vacuum

My Bissell Model 3760-4 is not working properly. The belt has been replaced (and checked 3 times), but the brush bar does not move when the brush motor button is on. The little metal turning piece that turns the belt is turnable with one's finger when the belt is off, but when we put it all back together and turn on the vacuum, the brush bar does not go around and the burning belt smell returns. The portable part of the machine works properly. It's the brush bar. It has been cleared of hair, etc


... Bissell Lift-Off(R) Revolution(R) Turbo Upright Vacuum

My bissell brush band has come off and wont stay on thus the brush will not turn, there is also a black arm type thing on a spring inside (on both sides) on the pump belt side it has broken - the side where the brush belt is, help im searching for parts and a way to fix it but im getting no joy, incidentley the brush belt thickness looks way to thick for the small thickness for the brush belt cog (?) to stay on........am i missing something? so i need to get the arm thing replaced plus find a


... Bissell ProHeat Deep Cleaner Upright Vacuum

Changing belt - Eureka Whirlwind 5740


I tried the website for manuals but no luck. I called the toll-free # 1-800-282-2886 and got a rep right away. I gave him the model and s/n (lower bottom on the back side) and he walked me thru it. For the model I have, there are 3 screws to remov ... Eureka Whirlwind Litespeed 5740 Bagless Upright Cyclonic Vacuum

The Panasonic MC-V7515 has two belts. The local vacuum repair guy says he only has a part number for the drive belt, which is UB-9. How do I find a replacement for the other belt, the one which directly drives the beater bars? By the way, this vacuum has great suction, but otherwise is far inferior to my previous Panasonic vacuums. The cheaper models aren't a good buy--stick with the more expensive models.


... Panasonic MC-V7515 Bagged Upright Vacuum

I have a Eureka 4800 series the Boss upright with a bag and Hepa filter. I love it! I was just vacuuming with the hose part and all was well and then suddenly the lower brush came on and a "burning" smell followed. Thought it was the belt so my husband was going to put on the new belt which I had on hand! When he turned it over, the "bar" that holds the belt looks as though it "shot through" the plastic side of the housing on the vacuum. There is melted plastic on the outside of the vacuum and o


I had the same problem. Take out the old belt if possible. Remove the 4 screws inside the filter and the 3 on the front of that housing. pull out the foam around the motor. carefully pull out the suction tube that is press fit against the motor. ... Eureka 4874 Bagged Upright Vacuum

Replacement parts... I've got a 3594 Bissell and the belt has come completely off. In the process of breaking, it bent the metal guide inside the motor housing and melted the plastic that holds the guide and keeps the belt inline with the roller. I've got it running again by using a screw I filed all the threads off of, but it only works for 10 minutes at a time before breaking another belt. This process is getting expensive, as it usually takes 30 minutes to completely vacuum the house. Is ther


Most likely it is the top cover that needs to be replaced, part #2031238 and is around $30. It would have that guide on it. ... Bissell 3594 CleanView PowerTrak Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0920 seconds