Having problems with your Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray ?

I have a Shark corless sweeper since Nov 2004 and it now makes a lot of grinding noise. How do I get rid of the noise, it works well but noisy....

Answers :

If its that old the plastic gears and parts are probably wore out. Euro pro does not provide many parts other than belts. might be time to replace it
Repair Help & Product Troubleshooting for Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Shark corless sweeper since Nov 2004 and it now makes a lot of grinding noise. How do I get rid of the noise, it works well but noisy....

If its that old the plastic gears and parts are probably wore out. Euro pro does not provide many parts other than belts. might be time to replace it ... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

I have a windsor vsp 14, it is making a bad grinding noise, when I take the top blue piece off it stops, the brush works fine and when I put the top back on it grinds really loud and gets hot. it still vacuums and the belt and brush are working fine, can't figure it out. and when the lid is on I cant see what its grinding on. It only makes a grinding noise when you pull handle back and engade to vacuum flor and stops when you put it upright.

... Windsor VS14 Versamatic Bagged Upright Vacuum

November 2008 I bought a Simac Stirella 9000D steam generator iron. Recently its been leaking water out the bottom of the regenerator. It makes a noise when it is trying to get the steam to the iron and it works then but afterwards when the noise stops it stops steaming and I find a puddle of water underneath the regenerator. Also a little steam comes out of the water tank at the top. I understand this is happening because of scale in the base unit. Can I get something to get rid of the scale? -

... Vacuums

Had my dyson root cyclone for about 4 years now, and in the last year it's had a few problems. About 4 months ago it started to make this awful grinding sound when the roller bar was engaged and I took it to a repair shop and they said it was the roller bar itself. The shop replaced the part and it worked fine for a couple of months and then it started to make the grinding noise again. I tried the clutch reset suggestion (turn it on its side and turn the carpet/bare floor switch slowly back and

Bdepends how much thay charged you for a roller brush because you can buy a good vac for about 100 pounds with a 12 month guarentee so its up to you ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have vax 1800 pet vacuum. It is picking up fine but very noisy. I have replaced the belt in the past and the noise started then. On looking at it closely today I noticed brushbar was getting worn where it slots in at the side so I suspect it wasn't fitted in properly after replacing the belt. Now in properly but still making terrible noise. There is a bit of a rubbing noise when brushbar moved round. Do you think the brushbar needs replaced? How do I lubricate the bearings to try that bef

Spray the end of the brush-bar were the bearings are with WD-40 if that solves the problem replace the bearing when it starts screeching.. ... Vacuums

110-220V Dear Sir, I purchased a kirby sentria vacuum cleaner from ebau two weeks ago. I currently resid in the UAE with 220V power. My maid has plugged the vacuum to work with it unaware of the voltage difference, a terrble noise as mentioned came from the cleaner as well as a smell. She unlugged it and stopped t from operating. Can you please let me know how can i assess the damage? If this model has a switch from 110 to 220V IS there a solution with transfromer or motor to make it work? Thank

You may have burnt up the motor field when it was plugged into a 220V power source. But there are drop down transformers you can get to reduce the voltage form 210 to 110. AS Radio Shack or similar store would have them. ... Kirby G4 Bagged Upright Vacuum

Making noise my bissell proheat 2 is making sort of a grinding sound. My belts and brushes work fine

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

With cleaning carpets with the Stowaway when the head gets a blockage it makes a high pitched whining sound and requires unblocking - then works fine. Now when vacuuming the head always makes the same sound when the head is against the carpet. you can also see that the rollers are slow or stopped. We have pulled the Stowaway virtually completely apart and checked for blockages as well as washed the filter and no difference. Any ideas?

... Dyson "Stowaway" Canister Vacuum Vacuum

No Suction My two year old Kenmore Progressive stopped working in January. The guy at the Sears service center convinced me that buying a new one would be cheaper than getting it fixed. So I bought the exact same model and now this one has given out in the exact same way! I'm so confused. When I press on, it lights up and makes the whirring noise. Everything seems to be working but there is no suction anywhere. Not in the main part or the hose and there's no "cyclone effect" in the chamber. All

Try looking within the vacuum to see where the suction is getting stuck at. You may have to do some disasselbmeing but this is a manufacturers problem. You should also try to speak to the manager at the support and make a big dispute until you get yo ... Kenmore 31913 Progressive Direct Drive Bagged Upright Vacuum

Horrible noise The same problem that has been the other people have experienced, I can make the noise stop if I switch to floors, but it doesn't work well on carpets. Has anyone been able to fix this problem?

It sounds like you have a blockage. Go to this at Dyson to look at your item in more detail. They have good support here for your item. Just copy and paste into your browser.http://www.dyson.com/support/help.asp?product=DC17-ANIMAL&ar ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

My Kirby 2HD has started making an odd roaring noise but still works fine. I have taken the front assembly off and cleaned and adjusted the roller and checked the belt. The noise seems to come from the motor housing. I have tried to wiggle the main shaft at the front (bearings?) and it seems tight. Can't seem to get the other housings apart. Any ideas? Thanks, John

It is quite possible, it just needs lubed. The motor comes in direct contact with dirt so, you have to make sure the front bearing has a drop of oil on it from time to time. If it starts to scream at you within one month, after oiling, the bearing ... Kirby Heritage II Vacuum

Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th

... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I can't get it to work, it makes a noise like OHH OHHH then says check tank Also it has never picked up all the water from My black shiny tile floor, so being disappointed have only used it 2 or 3 times. iRobot Scoomba mode l# 6050 I keep writing about this, are you receiving?????

... iRobot 5900 Scooba Robotic Wet/Dry Vacuum

It starting to put out a hot type smell. I have tried cleaning the filters real well and even tried to see if there was problem with the ozone filter. We have checked and could not find a jam. I know the hose has excellent suction. The vacumn works but the intelliclean sensors will not. It only takes about 15 seconds or so for the odor to start. Then it gets real strong and it makes my eyes water

Hi,The hot smell could be from the belt or the motor. Turn it on for a moment, turn it off, then flip it on its side and smell the belt that drives the brush. If that is where the smell is coming from, then your belt is burning up. ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

There seems to be a wheel that holds tension to the belt which came off. Now the belt spins and makes a grinding noise. I cant figure out how to get to the belt? Any one have advice?

I can help you a lot further if you can send me a picture of the bottom side of the vacuum. My email is [email protected] Once I see a picture this will help me tell you how to fix it. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

We have an Ebac Homedry 660 dehumidifier. It makes a noise when started and the red light indicating water tank full comes on. It has been inspected by a local repair shop and we have been told that the 'Fan' is not working. The workshop does not know how to get a spare part. Who is the repair agent in Auckland, New Zealand?

... Vacuums

I used the vaccum with out a bag once and when I put the bag in and started it it would not work. It makes a lot of noise and there is no suction at all.

If your machine requires a bag and u use it without one then the dirt has no place to go but through the motor. It sounds like your motor is shot. ... Hoover Vacuums

Hi -- I have a Kirby Sentria and it is great except that I am getting no suction at all through the big silver power head. Suction through all the other attachments works well. I haev tried it with the roller belt on and off, and that doesn't seem to make a difference. Am I missing something?? Thanks!

You can take off the power head and look in that whole where the belt is and see if there is a paper towel or something in there clogging it up. Also tug on the belt and make sure it is tight - because if it is loose it is broken and you ... Kirby Vacuums

Have a rexair model D series vacuum cleaner that worked fine until recently. Started making noise and then started smoking/overheating. I took apart the machine cover and am unsure how to get it tore down to see the motor or belt in there. Please help!

Below I have listed a link to the manual that has instructions on how to change your belt and a link for the replacement belt you need. ... Vacuums

Hoover Savvy making grinding noise after getting sheet stuck in beaterbar

Sound like the bearing are shoot ... Hoover U8181-900 Savvy Upright Vacuum

Making loud grinding noise brushes not working

... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

I ran over a big floor rug with my vacuum and some of the strings from the rug got tangled in the roller on the vacuum. It makes a terribly loud noise even now after I have cleared the strings from the rollers. What else can I do to get rid of the loudness?

Loose area rugs should never be cleaned with any revolving brush vac. They will damage the rug by destroying the fringes and corners. In some cases the brush will also pull out tufted as the rug is made so poorly. Natural fiber rugs should never have ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have Necchi Lydia 544, inheretade, and don't know which way the needle is fixed! what side does the flat part of the needle face? Also, what are the two bobbin holders on behind the main body of the machine, and how do they work? And, how the hairy heck! do I thread it? finally, for now! How do I get the bobbin holder to ...a...hold the bobbin, and b...make it stay in the machine, ..well, it obviously attaches in one way only, and I cannot find that way!? Thanks, Yvonne.

Hi,Here are some websites with useful information on your machine:http://www.free-guitar-tablature.com/Lydia.html This one shows how to take the bobbin case out with pictures.http://www.youtube.com/watch?v=FbEMwLNzsG4 ... Vacuums

Motor just makes 4 or 5 small clicking noises when you pull the trigger, then stops. The little lights illumintae around the "max" button as well. However, the motor does not engage in the slightest. There is no blockage at all. I have owned the vac for 10 months and know the sounds of blockage and clear them immediately. I just used it in the morning, plugged it back in and it has not worked since. Any ideas?

... Dyson DC35 Handheld Vacuum

I have a Vax u90 vu pa,it works very well but very noisy,any suggestion to lower the noise? Thank you.

... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1105 seconds