Having problems with your Euro-Pro EP602 Bagless Stick Cyclonic Vacuum ?

No suction It switches on fine, but there doesnt appear to be any suction and it heats up very fast. the tube has mild suction.


Answers :

Check the tube that leads down to the brush head for clogging as well as\012 any motor or HEPA filters. If that still shows nothing, take the cover\012 off the brush head (like you're changing the belt) and look for \012obstructions in there. Usually, if you have low suction on the \012accessory hose, the problem is with a motor filter, HEPA filter, or a \012clog where the hose goes into the unit. If you have good suction on the\012 accessory hose but none on the floor, it's usually in the brush head \012(clog or broken belt) Good luck
Repair Help & Product Troubleshooting for Euro-Pro EP602 Bagless Stick Cyclonic Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

No suction It switches on fine, but there doesnt appear to be any suction and it heats up very fast. the tube has mild suction.


Check the tube that leads down to the brush head for clogging as well as\012 any motor or HEPA filters. If that still shows nothing, take the cover\012 off the brush head (like you're changing the belt) and look for \012obstructions in there. Usual ... Euro-Pro EP602 Bagless Stick Cyclonic Vacuum

My bissell proheat upright steam cleaner is spraying out through the attachments just fine, but will not spray to the floor when using upright. we've taken it apart to find that there is no water at all going through one of the hoses, but it appears the hose is connected behind the on/off and heat switches, we can't seem to figure out how to get in there to replace that hose....any suggestions on how to access this?? just curious how you would get in to replace the hose, we know it is the hose..


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My vax power 8, 2200 watts 300 air watts 4L capacity upright Hoover is brand new, I emptied out the dust/dirt collecter and cleaned the motor filter yesterday for the first time, i switched it on and all fine, the brush is spinning and the hose is sucking, put the Hoover to work it's fine for about 30 seconds then then suction stops and its dead it won't collect no more, so switched off taken apart again and the motor filter is blocked and full of dust, so I unblocked it, do the same process aga


I had the same problem. It looks like the seal on the lid on the bottom of the cylinder has fallen out when it was emptied. There is no longer a proper vacuum being created so you don't get the cyclone effect and the dirt doesn't collect where its su ... Vacuums

I have an IS222 Bernina Steam Iron that quit steaming today---the iron heats up but the steam switch doesn't light or heat. It appears that we needs a new steam switch. Can you furnish this?


... Vacuums

We have a dyson dc 07 animal the machine was working fine then switched off after returning to the machine minutes later it wouldnt switch on, i removed on off switch cover and used a short piece of wire across the brown wires flicked the wall switch and it worked, aha i thought faulty switch aquired a new one to no avail and now even the short piece of wire trick doesnt work, has the motor died do you think, it wasnt over heating or making strange noises prior to refusing to work


It could be the motor. I'm having to replace the brushes on my DC 05. It appears that you can only get brushes for the YDK motors in the DYSON, not the Panasonic motor. Which might be saying something about the YDK motors. What happens is that the ca ... Dyson DC05 Cylinder Bagless Canister Cyclonic Vacuum

I have a Hoover Elite Rewind model #uh71009. We moved recently and it was jostled around and the red power switch popped out. I put it back in but it's stuck; it stays either left or right, it doesnt move back and forth. It appears there may be another piece missing from the power switch...all I have is the red switch and a tiny cylindrical metal tube with a spring on one end. This piece fits into the hole on the red switch. Inside the vacuum itself where this goes, there is quite a large cavity


... Vacuums

No suction Just received my refurb. dyson animal bagless. Finally figured out how to get it all together, turned it on and there is no suction coming up thru the beater bar. The hair is just collecting around the bar and not going up into the canister. It appears all the suction is going thru the open red end of the attachment hose, which has a vented cover piece. Am I missing a piece or is there a switch to turn of the attachment suction?


So the red hose isn't connected to a part on the vaccum so like it is connected to the connester but not to an opening just above the beater bar, this is the only idea i can supply you with. good luck, maybe i got lucky and helped you out. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The handle for my Eureka 5993 AVZ was getting very hot when used. Finally, the wires around the switch melted and now the vacuum will not work. What is wrong? Is the switch bad? The wires only melted in the immediate vicinity of the three-prong switch. Nothing else appears to be wrong; the vacuum worked fine when it was running - except for the handle getting hot. Thank you!


Try cleaning all...\015\012if have sam paoblem need replaced main motor.... ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

Hello, I have a Hoover 3200 Turbo Power vaccum. while the motor appears to be working fine the vaccum no longer picks up the dirt. I turned the vaccum upside down and the belt appears to be broken. would a broken belt stop the pick up, there appears to be no suction. This vaccum is approximately 10 years old. is it worth fixing? I live in Virginia Beach Va, where would I take the vaccum for repair? my zip code is 23456- Thanks Cleta Goode


... Hoover Vacuums

Dyson DC07 My DC07 has been working fine, but now does not pick up. If you put hand over the tube end the suction is fine. Any ideas. Thanks


This is an incomplete solution. Mine (DC 14 Animal) worked great and\015\012then it didn"t and then it did after checking to make sure that all the\015\012parts were on securely. I noticed that while the suction sort of seemed\015\012normal, it was n ... Vacuums

Hi. DC14 not running. Repeated pressing of the switch occasionally produces a split second whirr from the motor. I had been picking up plaster dust for some time but stopping regularly to clear out filters and 'the little tubes.' The switch is fine. I cannot see how to get at the motor. Thanks , Chris


Hi again. I finally figured out access to the motor. One of the brushes was burnt and broken. I have ordered a replacement set and cleaned up the comutator ( spelling ?). Thanks, Chris ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

I get plenty of suction at the hose, and none at the brushes. Also, the vacuum will not remain upright when I push it up. It appears that the part that switches the suction from the hose to the brush area is not engaged.


I looked up the problem where the machine would not stand upright, used that solution, and it worked. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!


Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums

I have a dyson that is picking up just fine when on vacuum mode, however when I try to use the suction tube there is no suction at all. It is not blocked and the canister is empty. Help!


Hi, I have an upright DC03, brilliant machine. Mine wouldn't **** and had the following symptoms;\015\012\015\012- it sucked ok from the top hole where the canister joins the unit\015\012- with the canister the dust didn't spin aroun inside the ... Vacuums

My Dyson DC17 beater bar motor works intermittedly. I have to almost whack it on the floor to turn it on and then shuts off again. I have checked the belt and it is fine, also have checked for blockages. The switch to turn the beater bar on or off will not work when the beater bar motor is off. the suction is fine though.


Buy a Kenmore for less money ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Shark Steamer model S3325 will not power on; switch appears to be working but will not indicate on and will not heat tank. I can hear it try to start the heating element (secondary clicks) however, does not seem to work.


There's a thermal fuse inside. If it gets too hot, the fuse will blow and the thing won't turn on.\015\012\015\012It has a 216 C temp limit. You can find thermal fuses at radio shack for less than 5$. If you're adventurous enough, you can fi ... Euro-Pro S3325 Handheld Steam Vacuum

Hi My hoover will work for about 1 minute (suction seems fine ) and is then cutting out-clearly over-heating.I cannot find the manual -can you suggest possible solutions.Thanks


Check the hoses and hose ports for clogs. Detach the hose and drop a marble in one end, allowing it to run out the other. \015\012If this is a bagless model, check inlet behind filter for clogs. If it has a bag, try changing the bag. ... Vacuums

Dyson suddenly stopped working. About a week ago it had a suction issue. One of the upright tubes was clogged, cleared it and it worked fine. Today I was vacuuming and it simply powered off. The vacuum is maybe a year old give or take some.


Hi its Darran at Dyson.Sorry to hear you are having difficulties with your Dyson. So that we can help, please contact our Helpline on 0800 298 0298 (UK) or 1866MYDYSON (US). One of our advisors will be able to run through some ... Dyson Ball DC24 Bagless Upright Vacuum

All the suction has been lost at the bottom end, the hose still works and sucks fine. what can be the problem? there doesnt appear to be any blockages either


It sounds like you must have a blockage behind the beater brush on the bottom of the v ac ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Oreck XL21 just will not work at all any more. Beater is clean - belt is fine. Fresh bag - inflates. Took the thing apart - checked for blockages at intake, bag entry, and the tube. It just doesn't vacuum anything. No suction at all for anything stronger than air. I'd say it doesn't ****, but that would be ironic. Are these known for just "quitting" after a while? We take it in for maintenance as recommended to replace filters, etc. Is there some miracle trick to make it work or sho


Did you make sure the brush turns freely? Even though it is clean, if it does not turn freely with the belt, it will not beat the carpet and pull debris up into the unit.\015\012\015\012Another (drastic?) thing to try would be to take the unit ... Vacuums

Water suction My Bissell Proheat Clearview is not sucking up water into the tank, motor appears to be fine


Here's what I did. On the top of the water bucket there is a red oval screen, remove and clean the screen and replace. Also, next to the screen is an oval opening which meets up with a black oval gasket on main unit. Inspect the gasket and replace if ... Bissell 1698 PowerSteamer ProHeat Upright Wet/Dry Vacuum

My dc14 animal works fine in Vaccuum mode but when I switch to the extendable tool the sound of the vaccuum changes to a higher pitch noise and I get very little suction through the hose. Any suggestion


Your hose has a restriction. To fix this, use a broom handle and insert it into the hose as far as it will go. If the hose can be removed, take it off completely and do this, if not be careful so as to not damage the sweeper with the handle. anoth ... Dyson DC14 Bagless Upright Cyclonic Vacuum

I have Bissell ProHeat 2X 9300-M that I tried to use again today. Is does not dispense solution when turned to Floor Cleaning, when switched to Hose it seems to be working fine. Brushes and suction are working as well. Soap and water containers are full. I took off and replaced tanks, waited to prime the pump multiple times without success. Not sure what is going on.


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

I have a vax mach 6. There is very little suction when using the tools and it will switch itself after a few minutes. I have had it to bits and cleaned it. I can not find any blockages. The belts also seem fine.


Http://www.vax.co.uk/downloads/pdf/u90-m5_u90-m6_series_user_guide.pdf ... VAX Appliances Vacuums

Little green machine pro heat pet the collection tank wasn't collection and dirty water was coming out of the bottom. i took it apart, cleaned it up and put a new "duckbill" gasket in. then it quit spraying, but i think i got that working again. now after i spray and get a good foam on the carpet, i switch to suction and it seems very weak. i can see the water moving (trickling) from the head into the hose but it is not reaching the collection tank -- actually, i am not sure where its goin


... Bissell THE BISSELL LITTLE GREEN MACHINE Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0830 seconds