Having problems with your Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum ?

My HEPA Shark Model 238 is great when the moter operates at high speed. However, periodically, it slows down resulting in no turbo action and virtually no pick up of eve the lighted dustball! Sometimes a good swift kick will bring the moter speed back to "HI", but sometimes no matter what, it won't speed up.rnHELP!


Answers :

If the motor is over heating, it will slow down and may even stop all together. A solid knock could reset the thermal switch prematurely. Clean it as best you can around the motor and try it again. If it does the same thing, turn it off for 20 minutes or more to let it cool down and try it again. It only takes a few minutes for the motor to get hot. It takes a lot longer to cool off. If it has done this a lot (40-50 times) , cleaning may not help. Stay in touch and let me know how it is going. Thank you. Roger
Repair Help & Product Troubleshooting for Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My HEPA Shark Model 238 is great when the moter operates at high speed. However, periodically, it slows down resulting in no turbo action and virtually no pick up of eve the lighted dustball! Sometimes a good swift kick will bring the moter speed back to "HI", but sometimes no matter what, it won't speed up.rnHELP!


If the motor is over heating, it will slow down and may even stop all together. A solid knock could reset the thermal switch prematurely. Clean it as best you can around the motor and try it again. If it does the same thing, turn it off for 20 minute ... Euro-Pro HEPA Shark EP238 Bagged Canister Vacuum

I have a vx550cc that keeps kicking in and out quickly, then shuts down for a few seconds and starts up kicking in and out again. There is lots of suction at all the outlets and sweeps. The dirt bucket has been emptied and the filter cleaned. Al the LED lights light up when the motor kicks out, then back to one green when it starts back up. This unit has worked great for four years with no problems.


... Broan-NuTone VX475 Bagged Central System Vacuum

Good suction, but not bringing the carpet nap back


Is the belt to the roller brush installed correctly? Check the height of the machine from the carpet. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Hoover Savvy The red light for the dirt finder is on when pushing forward and the green light is on when pulling it back. This happens all the time. It's like the dirt finder sensor isn't working right. It seems to be picking up good and we keep the filter clean.


Does this happen at both Dirt Finder Sensitivity settings? ... Hoover U8171-900 / U8172-900 / U8173-900 / U8174-900 Savvy Bagless Upright Vacuum

The kick stand that lowers the vacuum when in use got in a position where the red foot pedal would not come back up to bring the wheels down and the vacuum rest in the upright position. We took it apart and corrected the position, but the side with the small circular spring came out and we are not sure how to attach it back, exactly where it hooks onto. Can you help show us where it goes?


... Dyson DC25 Animal Bagless Upright Vacuum

Over heating Light Comes on as soon as I try to turn the unit on. I have a Miele S558 Silver Moon vacuum that has only been used once and it shut off and will not come back on. The overheating light comes on as soon as I try to switch speeds on the handle or turn the unit on at the canister, and the vacuum will not run. Do you have any idea what the problem is?


... Miele s558 Silver Moon Vacuum

Belts I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do t


It is the flat belt that gets stretched and should be replaced at least every 6 months. The V belt wears down so it won't it right in the brush roll V. Maybe the belt tensioner wheel has a problem, sometimes they get hook up and won't engage the V ... Vacuums

I have a Hoover self-propelled windtunnel, purchased 6-04. It gets light use. I have replaced the v belt 3 times, once under warranty, and it must be replaced again. It appears to be in very good condition, but is stretched too big. When I purchased 2 v belts a year ago, one was already too stretched,but when my Dad took it back, the salesman put it on another model and said it was fine (Dad never mentioned this to me). Is there a way to adjust the vacuum to hold the belt tighter? Do they re


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=675093\015\012Generic problem for all Vacuums\015\012I have a Hoover self-propelled\015\012Posted by kl ... Vacuums

I have a VX3000C Broan vacuum and the motor sometimes runs lower and comes back to normal time and time. Plus, now it lamost stops before coming back to normal speed. Can someone explain to me what that might be or if it did happen to someone else? It doesn't stop, but runs at very low speed and come back. It is like if a connection is not made properly. But it does the same at my 3 connections and I did check the one on the vaccuum itselfs.


... Broan-NuTone VX475 Bagged Central System Vacuum

I have a remote Hunter Ceiling Fan w/ remote 1-2-3 fan speed buttons and one on/off/dimmer light button. Model Number CP-9110R. It only has one pull string and it is for the light. I would like convert the light to work off of a simple wall on/off switch and the fan to be controlled by a 3-speed pull string. Can I by-pass all the sensors and make it work?


I see noone has answered so I will.Yes,it could be done,but if there is not a conversion kit for your fan,it would not be wise to do it.For starters,all of the things required would probably cost at least $15.Also,there is at least one tool you would ... Vacuums

My new H2O Mop Ultra (Danoz) seems to heat up ok then when the light switches to green and I start using it, the orange light comes back on as well as the green. Produces steam to start with but then it starts to spit water too and everything ends up wet. Any ideas on whats wrong or should I just send it back?


That is a major hardware fault, I have seen this numerous times with these H2O mop's... They seem to either work perfectly for a long while or have problems right off the bat. You definitely want to send this unit back and either get a refund or at ... Vacuums

I have a Kenmore Progressive upright model 216-37100800. It is only around 1.5 years old. My wife said that one day after she plugged it and turned it on, it whirred up but then shut off. Since then it will not start. I have noticed that right after I plug it in, if I try to turn it on, the first yellow light in the series of dirt sensor lights turns on then shuts off. After that the light will not light up on pressing the power button, unless I unplug it and plug it back in again. I have seen o


... Kenmore 25512/ 25513 Progressive Canister Vacuum

My Dyson DC28 works fine for a minute then it's like if the brush head gets too much resistance it quits spinning and the light starts flashing. When I turn the vacumn off then back on it's f


Hi Gayle,I'm sorry to hear you're having difficulties with your DC28. From what you've described, it sounds as if you may have the brushbar set at a level too low for the type of carpeting you're cleaning. If you select a higher carpet settin ... Dyson DC28 Animal Bagless Upright Vacuum

I have just purchased two (2) Electrolux Nimble vacuum cleaners. Not one, but both, straight out of the box, the beater bars will not run. It turns on, select carpet, and lower the handle, the red light to check beater bar/or filter lights up. You can reset the light by unplugging the unit, then plugging it back in, but with same results. Now the kicker, if you take out the handle, select carpet, lower the body by the carry handle, it will run and operate correctly, however, as soon as you r


... Vacuums

Press the power button on - good got a green light (new battery) press the clean button - got a green light iRobot runs for a couple of seconds and stops, then starts, then stops. After two or three times I now have a red light on for the Status. All of the wheels seem to be clean. I used compressed air to clean the underside. But still have the start stop problem.


How many times does the red light blink before it pauses? ... iRobot Roomba Discovery SE Bagless Robotic Vacuum

I have a stanley hid0109 flash light but it wont show the main light. i charged it and still wont turn on instead the red light on the back flashes.


... Vacuums

Miele vacuum Sometimes when I hit the auto roll up cord button or even move the cord, the power vacuum goes off. I move the cord again and it comes back on. I took it apart and looked at the connection from the cord to the auto roller. These are the electrical slip on type connections and are still in good shape. There are no bends in the cord. I air dusted everthing inside, put it together (with no extra parts!). Good news..it powered up so I did not break it, but it still has the same problem.


... Vacuums

I was changing a light bulb with one of those metal extension rods that unscrew and screw back in the replacement bulbs. It evidently didn't seat correctly and pulled off the bulb and created a quick "poof" type electrical short. I have switched out that bad bulb with a new one and can't get either the fan or lights to work. There doesn't appear to be a reset switch. I also swirched out the wall switch to see if that would make a difference and it does not. Any thoughts or ideas would be appreci


If you have not already done so, I would check at the fuse or circuit breaker panel to see if you have blown a fuse or tripped a breaker. ... Vacuums

Eureka 2961AVZ Will not start ...I get a momentary flicker of power about every 3d or 4th time that I flick on the power sw. Outlet is fine / Plug looks good / chord looks good / I see no obstructions ........Would appreciate any helpful thoughts ....Trying to get Mom's Eureka 2961avz back up and running. Thanks


CAREFUL! This is how my problems started. The cheap switches (and wiring) Eureka is using in some models, especially my model) should provoke a lawsuit imo.Here's my story, just in case it might help. Mine started with a problem very similar ... Eureka 2961AVZ Bagless Upright Vacuum

I have a raynor flight star garage opener. Had a lighting strike 4 days ago. All power is good. The opener even has a little green light on the switch that is attached to it. However the opener is not responding. Is there a way to reset on the motor by taking off the housing? I don't see any reset button on the out side of the housing.thnx w


You could always try unplugging the unit and plugging it back in. If that doesn't work the logic board is probably fried and unfortunately there is no replacement available for it any longer. You would need to buy a new opener. I'd recommend Liftm ... Vacuums

The low speed for bare floors won't work at all. The regular speed for vacuuming carpets turns on but spits items back out after a little bit.


There is only one speed on a central vacuum. The power nozzle motor has nothing to do whether or not you have suction. Sounds like you don't have any suction. Unplug your hose from the wall. Start at the unit. Short out the two low voltage wires atta ... Electrolux Central Vacuum

I have a Liftmaster garage door opener and the garage door faces south. Normally the opener works great except at certain times on a sunny day.The sunlight is not directly hitting one of the sensors but the door will comedown as far as half way and then it will go back up and the lights will flash. If I go inside and use the button I can hold it down until the door is fully closed. However, sure is a pain to have to take the car out, go back into the garage, shut the door and then leave the h


Sounds like a problem with a limit switch or something getting in the way of the electric eye that interrupts for safety reasons. \015\012Clean the electric eye transmitter and sensor of debris and cobwebs and make sure the wires are attached properl ... Vacuums

I have a Harmony vacuum that's a couple years old. I recently sucked a fair amount of dog hair into it and was unaware something was amiss since the things so quiet. It just shut down and wouldn't come back on. 10 minutes or so later it came back on but now it's got no sucking power. I figure I torched the motor. Good guess? What are my options--I'm out in the middle of no where but can get it to a repair shop 250 miles away. Is it worth trying to salvage or am I going to pay as much to get it f


I cleaned the whole thing out, changed out all the filters again and cleaned out the motor compartment. Then I discovered a huge clog in the line. Once I got that all done--it's now working like a charm. Moral of the story: spend more time looking fo ... Electrolux Vacuums

We just purchased a bissell pro lite and when we run it just a little while, both lights start blinking and we can't turn it back on without unplugging it for a few seconds. The manual doesn't say anything about it. What do the blinking lights mean?


... Bissell SpotBot Robotic Wet/Dry Vacuum

Good day, I took off the cover on a proheat upright, to install the suction diverter flap. Guy at the shop told me I had to do this but I don't think it was really necessary. Anyway, I am having a real job getting the cover back on. The shampoo mix piston seems to be causing the problem seating the two halves correctly. I see no obvious "right: way to put the piston back in. can anybody help me. Thanks Richard


Hey Richard. Turn the shampoo mix dial so the spiral is all the way at the top when you are looking at it from underneath. then, you want the piston to seat in the top groove of the knob. You want the piston's end that jets out to fit in the space ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0839 seconds