Having problems with your Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum ?

Brush not rolling, no brush indicator light on.

Answers :

Repair Help & Product Troubleshooting for Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Brush not rolling, no brush indicator light on.

... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

After turning on power , brush roller freezes and indicator light turns red

Try turning the roller by hand UNPLUG VACUUM FIRSTit should turn very easy, otherwise it is bindingall uprights have this problem eventuallyhair and fibers get in roller bushing and seizeluckily disassembling is relatively easy, same ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Brush roll won't turn on for the shark NV22L vacuum. the light on the brush roll is dark, not red or green

Atthe bottom of the vacuuam are screws to take off...two of them are near the rear wheel assembly....two of them are behind the front mini wheels (just pry the front mini wheels so that they pop out...they pop back in)Remove all of the screws. Re ... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems

Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

When vacuuming on position I, the motorized brush does not roll and light does not turn on.

Dont use brushes on wooden floors ,,,,this link is the manualhttp://www.sharkclean.com/manual/NV351_26_NV352_26_IM_ENG_SPA_101207.pdf ... Shark Vacuum. Navigator Lift-Away Bagless Upright Vacuum Cleaner NV352

My vacuum isn't working. The red light indicator comes on seconds after I start it, yet there is no blockage and the brush area is free of debris. I checked all the filters and no sign of blockage there either. The brushes don't turn and there is no suction. How can I fix it?

Brush motor not working. ... Fantom Vacums Cyclone XT Upright Vacuum

I have a minuteman c37115-14 MPV14 vacuum. When I turn it on the brush will rotate for a second or two and then it stops. The light indicates "brush is blocked". Any idea what my problem is? TY Mark

Check your brush roll for string (from the carpet) or other debris in and or around the bearings on the ends of the brush roll. Or check your brush height. If you have the brush too low/close to the floor it drags the brush down, telling the circut b ... Vacuums

Shark Navigator The brush roll light is green but it isn't turning

... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

The performance indicator light has come on on my Eureka capture plus. Last night a t-shirt got caught in the roller brush and now it won't spin.

... Eureka 12 Amp Capture Vacuum Upright Vacuum

My EL8602 check brush roll light on

... Electrolux Vacuums

On /off power switch works but when i engage carpet/floor switch nothing happens/ no light to indicate its working and roller brush not turning

... Miele S7210 Bagged Upright Vacuum

When the vacuum is running i get a check brush indicator lite, but once I put the hande in upright postion the light goes out

... Windsor SR12 Sensor Bagged Upright Vacuum

Brush rolls of my Euro-Pro Shark vacuum (model-UV 210CN) are stuck; the brush is unable to roll. Does that mean I have to the roll on one end or the whole brush unit? I live in Canada and if possible let me know where I can find a store. Thank you.

... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

Hoover windtunnel U6425-900 the brush roll is not turning. Both belts are in good shape, I cleaned the brush roll and it is free of debris, the setting is on carpet and the brush roll still will not turn. There is a "burning rubber" smell when you attempt to push the vaacum forward a few times. The small belt does not seem to be pulling properly but appears to be in good shape.

... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Spin brushes spin freely on steam vac when not attached to cleaner indicator screen not dirty speed selector is in high position brushes are clean spin brush indicator when brushes attached to machine does not rotate

If this is a Hoover Steam vac, the turbine which drives the brushes is bad. If not a Hoover, then what is it, they are different, need brand and model number. ... Vacuums

'Bag Full' light indicates at 1/3 bag

The sensor is a small hole into the vacuum chamber. It moves the alert system as vacuum inside the unit builds up.\015\012\015\012The filtration, built into the bag, is getting filled up and creating a higher vacuum inside the unit, givi ... Windsor SR12 Sensor Bagged Upright Vacuum

Irobot Scooba model 33501 the check brush light immediately goes on and irobot does not work. I replaced the brush and it still will not run and the brush light remains on.

... iRobot 5900 Scooba Robotic Wet/Dry Vacuum

Hoover windtunnel u6476-910. Brush does not roll. Flat belt and other belt are good. The other thicker belt (called V belt?) does not have tension with the brush roll. How do I make sure it is engaged? Is there a fix? Settings are in "Carpet", "Roll-on", etc. Cleand all hair and bags/filters already.

These machines had a defective switch and a bulletin was sent out to all service depots. If you contact any Hoover Warranty Depot, they will replace the switch, wiring harness and tool receiver under a no-charge warranty. It doesn't matter how old it ... Vacuums

ProForce 1500 has suction but the brush roll motor stops working.

... Proteam ProForce 1500 Bagged Upright Vacuum

Kirby Sentria brush roll not spinning! HELP!

This video will help you with your problem ... Vacuums

The brush status indicator

Try the brush belt condition ... Fantom Vacums Cyclone XT Upright Vacuum

When I flip the switch on my sebo x1 upright, a red light comes to the brush and bag icons. However, I cleaned out the hose and checked to make sure there is no obstruction from the brush to the hose also, or from the hose to the bag. It is clear that juice is coming to the vacuum, but there is no sign of life except the two red lights.

Thanks for contacting fixya. You should pull out the bag and reset the machine. You should take all the user replaceable items. And turn it on. You will get lot of errors. Then turn the machine off. Put back all the accessor ... Sebo Automatic X1 Bagged Upright Vacuum

Brush roll i am trying to find and purchase a new brush roll for my ge vacuum. The number on it says that it is 106585 and from what I can tell that is the same as 5550 parts. Is that correct?Thank you

I have the same vacuum for the last 5 years.  I dont know if its the same as 5550 (I assume it isn't) but I can give you the part number 61445-1.  It costs around $16 and you can call 1-877-207-0923 b/w 7 am and 8 pm Mon-Fri central time, o ... GE 106585 Upright Vacuum

Brush roll belt stops turning when in position to vacuum. Does turn when vacuum is turned onto side. Belt is in tact, brush roll is fine. What's going on?

I think I know what the problem is with your machine. It's a rather lengthy repair, and I'll be happy to photograph it for you (like I do on most of my Fixya answers), but I'd like to know before doing all of that if you still need help, or if you' ... Eureka Smartvac 4870 Bagged Upright Vacuum

Hoover Bagless Hello,      My Hoover bag less (Model U5280-900) is not picking up dirt like it should.  The brush roll is spinning fine, but the bristles on it are only about one quarter inch long.  I am wondering how long they should be.  The vacuum is quite a few years old.  Do you think it is time to replace the brush roll.  Could you email me at [email protected] about this topic.  The product bar below did not contain my model no.  The correct model no. is above in my message.  Thanks

If the belt is more than six months old then change it even if it is not broken. then replace your filters if that doesnt work than check the hoses for a clog drop a marble down them and make sure it comes out. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0436 seconds