Having problems with your Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum ?

I cannot remove the roller brush for shark vacuum

\015 I am trying to replace the belt on my shark vacuum cleaner and i cannot remove the roller brush as easily as it shows on videos and every other how to i have found because it is actually stuck inside holes on either side and not just resting on something i have pushed and pulled everything to get it out and it wont come out now i just have vacuum cleaner parts all over my living room. HELP ME!!\015

Answers :

Remove the rubber "bumper" material from the outer edge. Small slits are exposed where the roller is attached to the rest of the vacuum. u can figure the rest out. I wedged my finger in between the roller edge and lower plate. Use whatever you want. Hope that helps.
Repair Help & Product Troubleshooting for Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I cannot remove the roller brush for shark vacuum


Remove the rubber "bumper" material from the outer edge. Small slits are exposed where the roller is attached to the rest of the vacuum. u can figure the rest out. I wedged my finger in between the roller edge and lower plate. Use whatever you want. ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems


Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

My Dyson Animal has good suction and works fine for actually picking up dirt, but when I use the vacuum with the roller, I hear a grinding/rumbling noise. Its only when I use the vacuum with the brush rotating. It does not happen hen I shut the roller brush off. The belt is fine. I cannot figure out what is wrong as there are no clogs, debris, or foreign objects stuck in the brush or in the belt. The noise seems to be the only issue. The vacuum picks up fine. It just doesn't sound right a


Trace the path of the suction into the tank and see if there is anything loose or ingested.\015\012Also, remove the brush and clean as best you can. Perhaps there is something caught in it. Lubricate where it makes sense with some WD40. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

I have a eureka bravo upright model 9600. I have removed the hood . I need to remove the brushe roller to install a new belt. I cannot figure out how to remove the brush roller.


Check out this URL:\015\012\015\012http://www.svcvacuum.com/beltrep2.html\015\012\015\012looks like it has just what you are looking for.\015\012Would appreciate a thumbs up on this if you find it beneficial.\015\012Paul ... Eureka Vacuums

I was vacuuming my room and all of a sudden I hear this loud noise, then notice the roller brush isn't spinning. Thinking too much hair was caught I separated it from the rod and hose to clean it out, but noticed that the roller brush didn't move at all while I was cleaning it. I've cleaned the brush before and it would roll around with little effort, but this time I couldn't move it at all. After removing hair and string I put the vacuum back together and started it up, but the noise continued,


It sounds like if the rod is clean then there is debree inside the roller where the rod fits in too. ... Hoover Platinum Cyclonic Bagless Canister Vacuum With Power Nozzle

How do I remove the brush roller onthe eureka clean living vacuum model no 3281 AZ


... Eureka Vacuums

Roller Brush How do I install the roller brush. I didn't pay attention when I removed it and now when I attempt to vacuum my low carpet it doesn't seem to be working. The green light on the head of the vacuum goes out when I click it down to the floor. It didn't used to do that. Plus I think I smell something burning. Could the belt be broken?


Try a new belt. The ends of the brushroller are different sizes, so you can't put it in backwards. There are numbers and notches on the ends of the brushroll. These notches/numbers need to match on both sides when installing it. (probably need b ... Kirby Ultimate G Bagged Upright Vacuum

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

Hi, There is a high pitched whirring sound coming from lower part of the vacuum. When I tilt it toward me (while standing in the normal vacuuming stance) the sound sometimes lessens for a minute or so. I have tried the following things: -cleaned the two sponge filters -emptied the dirt receptacle -removed the roller and cleaned it -cleaned the brushes -the belt is not ragged and does not seem floppy -checked all of the airways for clogs (including removing the wheel base) Can you help?


Your looking for some dirt stuck in some thing you didn't check yet. with the roller out and the belt out of the way run it to see if it still makes the noise. if it does then you looking at the impeller or the motor bearing themselfs those bearin ... Bissell 3750 Lift Off Bagless Upright Vacuum

How do i remove brush from vacuum? - Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum


You cannot. Call cust service. ... Shark Helmet NV22L Shark Navigator Upright Bagless Vacuum

Shark vacuum roller brush attachment doesn't spin


... Shark Navigator Bagless Upright Vacuum

We have a Eureka Chinese p.o.s, model 6831. The brush roller won't turn, appears to be plugged with cat hair dang long hair cat. I cannot figure out how to remove the cover without breaking it after removing the screws, there is a u shaped collar on the tube in the way. Can anybody help?


There are a couple of tabs on both sides of the top housing that need to be unlocked by using a flat screw driver, then the top will come off. The u shaped collar on the tube will then give way to take the roller brush out to clean. ... Vacuums

The roller-brush on my Dyson DC17 makes a terrible noise at all times. I removed the cover and extracted all debris from this area, making sure all connections were as secure as possible, but that didn't improve it any. The vacuum still seems to vacuum okay, but the noise sounds horrendous. How do I fix it?


Check the belt to see if a layer or piece of it has come loose and is flappping around.\015\012Check for any loose parts that could be getting hit by the brush or other moving parts.\015\012Make sure the brush it tightly in place and can ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

Brush roller won.t turn. It turns for a sec. then shuts off. I have cleaned all clogs. This is a shark navigator. Can I remove bottom of vac to access the roller? The manual doesn,t mention this as a solution.


... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

How to remove brush roller from Dyson DC44 - Dyson DC44 Animal Handheld Vacuum Cleaner


... Dyson DC44 Animal Handheld Vacuum Cleaner

How to remove brush roller ultimate g - Kirby Ultimate G Bagged Upright Vacuum


Http://www.youtube.com/watch?v=At7tqnjD-Kc ... Kirby Ultimate G Bagged Upright Vacuum

We have the Kirby G six 2001 Limited edition vacuum and we cannot get the belt to hook on to the roller brush.


... Kirby G6 Bagged Upright Vacuum

After vacuuming over a thick strand of loose carpert my brush roller will not turn on its own. The piece of carpet was removed easily and the belt is not broken. Your assistance would be helpful. Thanks


Make sure you can spin the brush by hand. The belt got hot and glazed when the carpet was stuck and will need replaced. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

How do you remove the roller brush from a dyson vacuum cleaner


You will need a special bet tool. you can buy one from ebey. search for "dyson special bet tool" it is about $15. don't use your hands as the belt is very tight and you will hurt your fingers. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

The brush is not moving on the vaccume. I'm pretty sure that the belt is busted. I cannot see how to get the shroud off, so that I can get to the roller and belt. It all looks and feels like one piece, even when I start removing screws. It is a bag-less vac. The model number is - v1310rs. Thank you.


I know on my Eureka I had to remove a couple of screws on the bottom and then get a flat blade screwdriver and wedge it on each side of the base kinda next where the end of the roller would be and it snaps up and off. Really weird I thought but that' ... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

Cannot get the brush roller back in properly - Dyson DC17 Animal Bagless Upright Cyclonic Vacuum


You could try checking out this video on dyson replacements\015\012\015\012good luck ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I can't get the latch that connects to the brush head to engage. Thus the vacumn is extremely hard to push. It has suction, extreme suction. Rollers appear to be dragging. I've tried to remove and reinstall the head several times but cannot seem to get the latch to engage. Please advise.


It sounds like something has come out of it's socket. If the brushroll won't turn rapidly, your clutch is worn out ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Hoover windtunnel vacuum roller brush doesn't turn. Have removed hair and lubed and belt looks ok. Any ideas?


Does the motor turn?  if it does replace the belt. ... Hoover Vacuums

Brush roller quit spinning. - Euro-Pro V1828 Shark Stick Vac Bagless Vacuum


... Euro-Pro V1828 Shark Stick Vac Bagless Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0962 seconds