Having problems with your Euro-Pro NV31 Infinity Vacuum ?

Handle is loose and won't snap down and lock into position

\015 The handle just pulls out when I pull in back and forth to vacuum..\015

Answers :

This is usually caused by a build up of dust in the flexible pipe. It stops the pipe from compressing down and so you cant push the handle down far enough to get the latch to click home.
\015\012
\015\012Try stretching the hose to its fullest extent and while someone has ut stretched, give the lengthe of the hose a good beating to knock the drit in it loose. Alternatively, if you can remove the hose, fill it (and boy will it expand and slosh about!) with a mixture of hot water and floor cleaner (I use flash) Slosh it about intil the hose is full of gunk, then pour it away. Then, put the hose in your airing cupboard (Stretched out!) overnight to dry. When you put it back together it should now compress enough for the latch to clich home.
Repair Help & Product Troubleshooting for Euro-Pro NV31 Infinity Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Handle is loose and won't snap down and lock into position


This is usually caused by a build up of dust in the flexible pipe. It stops the pipe from compressing down and so you cant push the handle down far enough to get the latch to click home.\015\012\015\012Try stretching the hose to its full ... Euro-Pro NV31 Infinity Vacuum

Dirt devil model 08633 handle wont lock in upright position


... Dirt Devil Vacuums

Placing the handle of my Dyson DC07 into its upright and locked position causes the beater bar to stop turning. It will not start turning until the handle is first lowered to the working position and the Carpet/Bare knob is moved to the Bare Floor position and then back to the Carpet position. Then the beater bar turns until the handle is placed into the upright position. What might be the problem?


Hi its Darran at Dyson.The brush control is designed to switch the brush bar off automatically when you stand the machine back into the upright position. It is designed this way to protect any delicate floor surfaces when you have the ma ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.


I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Handle wont go to upright position


The red pedal has slipped out of position. On both ends of the red pedal you'll see metal rods (the axel of the pedal). On one side you'll see the metal rod sits into a long groove, on the other side you'll see the metal rod sits into a round hole. T ... Dyson DC25 All Floors Bagless Upright Vacuum

The canister wont lock in position like theres a part missing to push it up to lock in


... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dyson 28 handle is stuck in the locked and upright position. Vac runs fine, just can't get the handle to release to run the vac


How do you remove the air duct (plastic sliding piece) that is making the vacuum stay in locked upright p[position? ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Handle The handle will not lock up in any position. Are there parts available for it?


... Eureka Optima Pet Lover 439AZ Bagless Upright Vacuum

I keep searching for an answer and nothing seems to understand my issue. It's not that the handle wont go back into postition.. the extended peice of the handle used for specific areas such as stairs ; I don't know how to return it back to its orignal position so I can resume vaccumming.


Hi there,To reattach the wand and handle to the cleaner to resume floor vacuuming, just place the handle back onto the main cleaner body. The wand will then retract automatically down inside the hose - simply guide it back down through th ... Dyson DC25 All Floors Bagless Upright Vacuum

Handle The handle on my Eureka 439 AZ-1 will not lock up on any position. Are there parts available?


... Eureka Optima Pet Lover 439AZ Bagless Upright Vacuum

I'm trying to get my S7000 Miele to stand upright an lock in this position. It wont , i tried to see if foot release was jammed but cant tell it doesnt seem to release to let it move upright an lock in again..help


There is a rear dust cover that sometimes gets stuck, this will make it almost impossible to lock the handle up. First locate the cover which is at the rear right above the wheels. It's about 2"x8" and ribbed vertically and slides up behind the rear ... Miele S7210 Bagged Upright Vacuum

My Dyson DC27 Animal is stuck (Locked) in the upright position. Everything seems to be ok with no apparent cracks or breakages. I don't want to force it in case something snaps.


Dysons are notorious for this problem. You will have to just force it and clean any obstructions. ... Vacuums

Rotator brush not spinning. Handle is not in the locked upright position. Says it's beltless, so is this likely an interlock switch or drive motor problem ?


Hi, the brush roll will only spin when your handle is not in the locked upright position, once the handle goes upright - the brushroll de-activates ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

Kenmore 116.35922500 brush wont turn. Seems to come on if handle angle is held at just the right position but it is intermittent. Reset button is not popped up and doesn't seem to have any effect.


... Kenmore Vacuums

Carpet/bare floor selector will not stay locked in bare floor position when you move the handle up and down. Model 116.38612790


... Kenmore Vacuums

Bissell handle wont stay locked - Bissell Lift Off Floors and More Vacuum Cleaner - 53Y8


Sorry to hear you're having problems with the handle. You may want to have a qualified technician at one of our Authorized Service Centers inspect your vacuum. Here's a quick link to assist you in locating one. ... Bissell Lift Off Floors and More Vacuum Cleaner - 53Y8

Handle on kirby will not lock in upright position


... Vacuums

Handle won't release - locked in upright position


... Dyson DC28 Animal Bagless Upright Vacuum

Vacuum lock Vacuum will not go back into upright position. There is resistance as you raise the handle.


I just solved my own problem. I'm not much of a technical writer and I'm sure I don't know the proper terms but nonetheless...\015\012\015\012...When standing behind the vacuum, as if using it, just above the right rear wheel is a detach ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Rival model CM1100 coffee maker: I can not get the coffee carafe in the right position. Should it lock in? Sometimes the coffee does not enter the pot and overflows onto the counter. Should the handle be on the left or the right or maybe the center? Please help me. I am not a coffee drinker and when I try to serve it to friends, I end up with an embarassing mess.


... Vacuums

The cantister on my DC04 no longer stays secure when in position. It does not snap and lock into place as before. I found a small plastic tab about 1/4 inch deep and less than an inch wide on the floor. Looks like it has broken off the lockin mechanism any suggestions?


Check your warranty. If it's still good read to find out if this part is covered (probably not) and where to take it for repair or replacement of the tank. \015\012Unfortunately, it may turn out you'll need to buy a new vacuum. ... Dyson DC04 HEPA Bagless Upright Cyclonic Vacuum

No power unable to manually turn off power, i opened up rear handle hatch to inspect the mechanism/linkage. The red on/off button seems locked in the on position. I replaced the hatch and now i have no power at all. what happened? Is there a fuse?


This vacuum has a recall notice on it. It has to do with the switch. You might want to check... They will fix it for free ... Hoover U6437-900 / U6439-900 Windtunnel Bagged Upright Vacuum

Windtunnel handle position won't lock, and missing extension wand


... Hoover V2 U8130-900 WindTunnel Bagless Upright Vacuum

Eureka 439 handle will not lock up in any position . Are there parts available for the Eureka 439 AZ-1


... Vacuums

My vaccum has a 3 position handle. This no longer works, so I have to pick up vacuum to move it. Makes it hard to vacuum scatter rugs. It does not lock into place


What is the brand and model of the vaccum? the description i see says Hoover U6311930. When I check the info for this model it gives me maytag vaccum cleaner. ... Hoover U6311-930 Power Drive Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0452 seconds