Having problems with your Euro-Pro NV31 Infinity Vacuum ?

Can't find a belt!

\015 I've been searching everywhere for a belt, and I can't find it anywhere! I've been to target and walmart and home depot and no one!\015

Answers :

Go to a vacuum service store, they can match it up, they have hundreds of belts. check your local phone book under "Vacuum cleaner parts and service"
Repair Help & Product Troubleshooting for Euro-Pro NV31 Infinity Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Hi I have an electrolux "The Boss" hand held vaccum cleaner. I cannot find the instructions and am having problems changing the belt. It is model number Z57A. Product Number 900-250-006. It is the first time I have had a problem. I only use it occasionally for my caravan. So cant find the instructions and cant remember how to change the belt. Please help

You need top lace belt on brush roller and re[-assemble by putting plastic cover on which is retained by 2 recessed philips screws.. Prize off triangular coverat fornt.behing that you should see the belt lying loose.You need to get a blunt object to ... Electrolux Vacuums

Sweeper belt Hey , i own a fantom thunder sweeper and recently my belt keeps slipping off, i've disassembled it and put it back on a hundred times but it keeps doing it after a few minutes of cleaning , Am i missing a part to hold it on or somthing else wrong i've cleaned it and checked all the ports just cant figure it out and cant find any info online thanks for your time tina

Greetings from GoVacuum.com,Have you replaced the belt with a new one yet? You may want to try replacing the belt, as with flat belts like the Fantom Thunder, they do stretch out 4 -5 inches after time. We in fact recommended replacing ... Fantom Vacums XT450K Upright Vacuum

I cant find the belt in my eureka altima bagless. I am trying to change it and I cant even see where it was or goes.

On the hood of your vacuum, right behind where the brushroll would be at the front, you should see a silver screw on each side. Just remove the 2 screws and lift off the plastic hood. Your belt will be on the right side as you face the unit. ... Vacuums

Belt I have a bissell pro heat model number7901-1 and i dont know how to put the belt back on. The old one broke and i cant find my book.

First take off the cover on the left side of the top cover, then turn it over, remove the screw holding the red lock and pull the cap and brush roll out, remove the cap, remove the cogged belt, then you can put the new pump belt thru that slot, put o ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Belt cant find out how to change hover belt

Not sure yet, but I assume you mean the belt that drives the brush at the base.\015\012If it is an older style cleaner, there would a be cover held on by a few screws.\015\012This hold the brush in place so tkae note of how it is in place ... Morphy Richards Vacuums

Roller got power cord. This stretched out the belt. I replaced the belt, now the vacuum is making a noise. Cant find anything wrong, what could be making this noise?

Most rollers have several different positions you can install the brush in check and make sure the roller height is equal. ... Bissell Upright Vacuum - The Pet Hair Eraser 1 ea Vacuum

Bissell 8920 proheat x2 brushes not turning i only noticed this after i finished cleaning.. or kinda cleaning because of the brushes ntot turning.. water comes out fine suction is fine but its not scrubbing so its not as clean as it could be. manual part works well water coming out hot. I did take it apart and cleaned off all the hairs in hopes maybe that was it.. put it together still nothing.. No idea how the belts should look onit and i cant find a picture or a video showing how belts look o

Hello,\015\012\015\012Here's a link to a very helpful video that shows you step by step on how to access and replace the belt on your machine. When the brushes stop spinning, but the rest of the machine works fine, this is a tell-tale ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Hoover steam cleaner spin scrub brushes wont turn cant find belt

I just brought mine home...assembled per instructions and tried all the troubleshooting thus far to no avail. So I popped off the brushes per instructions and took a screwdriver to the hole where the brushes axle inserts underneath the vacuum and tur ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Cant find screws to remove cover to check the belt

... Kenmore 23612 Progressive PowerMate Bagged Canister Vacuum

Cant find my manual. Need to install a new belt. Rose

Have no manual, hwo do I change the belt on a Singer Mocel # 3510-4?\015\012\015\012 ... Vacuums

This was very helpful but I still cant find the motor spindle to attach the belt to. Do I have to take the entire plastic base cover off?

Not sure who helped you, was it me?\015\012\015\012Go to this URL:\015\012\015\012http://www.hoover.com/pdfs/manuals/U5167900.pdf\015\012\015\012In figures 3-21 to 3-23 you will see how the new belt i ... Hoover Elite U5061-900 Bagged Upright Vacuum

I have a hoover elite 200 it did not have a belt on it when i got it and i cant find the drive shaft.

You must remove the lid of the vac and find the pulley end of the brush. directly behind it one hand length you will see a small silver shaft. If the shaft is other than silver it is coated with burned rubber. or rust and dirt. Clean off the bu ... Vacuums

How do you change the belt cant find where to take apart to put new one on

Follow the procedure below:\015\012\015\012\015\012\015\012\015\012\015\012\015\012 ... Eureka 4874 Bagged Upright Vacuum

I am trying to replace the brushbelt. I have the brush off not surewhich end goes where. also I had it on once but the belt was off when it was supposed to on. I cant find my instructions ! help

I am going Kirby "G" crazy.\015\012I hope this URL will be of help to you:\015\012\015\012http://reviews.ebay.com/CHANGING-THE-BELT-ON-A-KIRBY-G3-G4-G5-GSIX-ULTIMATE-G_W0QQugidZ10000000003720039\015\012\015\012If it is of help, please rat ... Kirby Ultimate G Bagged Upright Vacuum

Cant find where the belt goes - Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Model number please ... Hoover Steam Vac Dual V w/ SpinScrub Vacuum

Where is the belt on the dirt devil vision turbo cant find it

The belt is to the left of the brush. You need to revome the plastic covering (4 screws) to see it. ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum

I have a broan central vac system need belt for cv315-b vac head cant seem to find one any idea where i can get 1 thanks

I believe that the Broan replacement part number for the belt for the CV-315 power head is a 9967-0585. available through a Broan/Nutone dealer. ... Vacuums

I cant find where to put the belt for the kirby g-six perfomance

Belt installation instructions HERE.Good Luck :-) ... Kirby G6 Bagged Upright Vacuum

I need to change belt and cant find instructions

... Vacuums

Cant find spare belt to order for my hoover. It's an upright durabrand model no. ymh29046. Then typ cbu1

Are you sure that your vacuum is a Hoover? There is a brand called Durabrand that makes vacuums but they are not related to the hoover brand. ... Vacuums

Shark v1420gb cant find the small tension belt

Also, looking for small tension belt? ... Vacuums

I'm using (or WAS using) a Eureka ''the boss'' model 8803. The belt broke, no biggie, so I replaced it with a Eureka model U belt, the problem is when I put the new belt on and turn on the vaccuum, the belt breaks again. I am also having trouble getting the brush roller to fit right when the belt is in place. I can't find any sharp edges that would cut the belt,nor can I find where any small bits may have broken. Anyone have a solution for me?

First, make sure you have the right belt, second, i am thinking that you are not lineing the roller up right, it will only fit one way. look at the ends of the roller and the grooves where it slides in, you should be able to see clearly how it goes. ... Vacuums

I need to replace belt but can't find where belt belongs,only says belt access. can't find belt.

Not easy to read, but this URL might be of assistance to you:\015\012\015\012http://canada.bissell.com/images/UserGuides/9500_107.pdf\015\012\015\012Please let me know if it does not help you. My assistance is free and I am more than wil ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Have the empower upright cleaner. belt broke. can not find part #36528-040belt. can find a lot of hoover belts but not this #.Is there another hoover belt that will work on this vac?

No. if the wrong belt you will have problems. This is a common belt for Hoover, it used to be 36528027, but the number changed to the 36528040, also 40201190 is the newest number for this belt. Most repair vacuum repair shops should have this belt. ... Vacuums

I am a professional maid and one of my clients just had her Hoover Elite Vacuum belt break. I bought the belts ... but cannot find a manual online and do not know what the model number is. I am scheduled to be in her home in exactly one hour! HELP! HOW DO I CHANGE THE BELT -WHEN I CANNOT FIND A MANUAL? Many Thanks! Lynn

This is no problem! You will need a flat blade screwdriver and about 10 minutes! \015\012 \015\012*Always use genuine hoover parts for repairs, discount store belts can be as much as \015\0121" longer than OEM parts ... Hoover Elite U5061-900 Bagged Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0653 seconds