Having problems with your Euro-Pro NV31 Infinity Vacuum ?

There is no suction, hoses do not appear to be clogged, is there a way to remove the piece underneath to see if there is anything clogged there


Answers :

The top cover to the housing comes off in order to get to the roller brush area to check for clogs. There are two screws in the back of this cover to take out and then the cover will come off.
Repair Help & Product Troubleshooting for Euro-Pro NV31 Infinity Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

There is no suction, hoses do not appear to be clogged, is there a way to remove the piece underneath to see if there is anything clogged there


The top cover to the housing comes off in order to get to the roller brush area to check for clogs. There are two screws in the back of this cover to take out and then the cover will come off. ... Euro-Pro NV31 Infinity Vacuum

My DC 17 is plugged. I can see through the small hole in the top blue "flower shaped" that the holes at the top of the canister are plugged with hair & dirt. I cannot see anyway to get to these small round holes. Is there a way to remove the top blue "flower shaped" piece? I have removed the inner cone from the clear canister but still cannot get up underneath.


Please kindly follow the steps below to clean your vaccum cleaner,1.) Remove the clear plastic handle. You\015\012will have to take out two screws and then unclip from the from the\015\012front. It's stiff, I gently used a flat head screw drive ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

The removable filter at the front is cleaned regularly, and is not clogged. However, the machine appears to be suffering from being clogged by dust, as it has started to make a high pitched noise, and I fear it may burn out. I can see some dust inside the front panel but cannot see how to remove the front to clean it out. (NB. I have located two screws - one on either side - but cannot see how to proceed further.) Please help! Thank you.


\015\012\015\012Hi,Here\015\012is a tip that I wrote about my Bissel but I bet you have the same\015\012problem and the hose is clogged...Bissell Bagless Upright\015\012 ... Vacuums

I have a Model 116.35922500 Kenmore upright vacuum cleaner. It makes a loud air noise when using the vacuum. I have disconnected and removed the hose to see if anything is lodged in the hose and it appears clear. It makes the noise when the hose is connected. When I remove it, the noise stops. When I place my hand over the hose, the nose re appears. I sounds as though the noise is coming from the fan or internal parts of the machine. So, when there is a load or pull on the machine, it mak


... Kenmore Progressive 35922 Bagged Upright Vacuum

Hello i own the bissle proheat steamer it turns on but no water or soap or suction from floor or the utensiles ive taken the take off the back to scope out anything that could be in the way but dont see anything the motor is making that clogged vacume noise witch makes me believe something could be stuck somewhere in it but it could also be no water is getting to the pump or despencer but the brissels still work belt for that is good where would i be best to check and where is the location of th


... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

Poor suction The actual sweeper seems to work ok, but the hose attachment has some suction but not enough to pick up things I think it should and not enough to make the power brush spin. I've checked everywhere I can for clogs, but I can't see anything. And there doesn't seem to be any way to check to hose itself for clogs. I've cleaned out the container and the filters, but there's still a problem.


Check the inlet down by the brush roll, make sure it is open, if it is then the hose itself must have a clog. If the hose comes off, drop something like a marble in one end and see it it comes out the other end, if it doesn't then you have a clog. ... Dirt Devil M1100009 Reaction Soft Touch Cyclonic Upright Vacuum Cleaner Vacuum

My Dirt Devil D2 Reaction upright vaccume cleaner gets clogged up with hair and carpet fibers in the hose and does not put anything but very little dust in the canester even though I can see it picking up way more. Any ideas?


... Dirt Devil Reaction Twin Cyclone Upright Vacuum

How to disassemble the brush to empty anything that might be stuck inside of the brush? The motor seems to be overheating, all belts have been checked, all airways are clear and the filter is clean. The vacuum is vibrating and releasing a burning smell, but still sucking up dirt. There is nothing stuck on the outside of the brush, but is there a way to check inside of it to see if that is where a clog is occuring?


If there's a burning smell and the belts are fine, the problem is going to be hot wires causing the insulation to melt, or the motor going bad. Discontinue use and have it checked at a repair shop. ... Bissell 6594 PowerForce Bagless Upright Vacuum

My Dyson vacuum works fine for cleaning the rug but the hose doesnt get any suction at all. I removed the hose and all the parts around it that I could and dont see any clogs or broken pieces. I lost my manual so I dont know if this is addressed, or if there is a switch Im not flipping. Gave it a thorough look but found nothing.


Hi there,Sorry to hear you're having a problem with your DC07. If you have suction through the cleaner head but not through the wand, it sounds as though you have a blockage. Although you say you've already checked for these, you may find ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Roller problem Roller keeps stopping. I've emptied the dustbin. removed the roller to see if it is clogged, but appears to be nothing impeding it.  It stops on a short napped rug, and even on the wood floor.  Is the spool that the roller slips into driven by a belt? Can I get in there behind the spool?


I have 3 Prontos, one in each part of the house. Two of mine had the rollers stop. I figured out the problem and it fixed both. Take the roller out by turning the plastic screw and popping the plate off. Pull all debris off the wheel that turns. ... Electrolux EL1000A2 Pronto Bagless Stick Cyclonic Vacuum

I just bought a Tfal Ultimate Autoclean iron FV 9450. I am reading through the manual and trying to figure out all the parts and functions. I cannot figure out how to remove the anti calc valve. I see it is part # 12 on the drawing but that piece on my iron (the bit with the little circles on it where it says, " anti calc plus') seems to be a flat piece of integrated plastic with no give or slide to it. .I cannot see how I'd possibly remove it. What do you do - push up? push down? The i


Anti-calc valve wings (grip) located at #3 of the 1-15 labeled description diagram that is part of the instruction manual. The wings are on either side of the dry/steam control #4. Lift up on the wings (grips) and the dry/steam control will accompan ... Vacuums

I have a Sears Upright vacuum cleaner, model 116.35922500. The vacuum wasn't picking up. I discovered a clog in the nozzle hose. I attempted to remove the cover of the brush unit to clear the clog. I was unable to remove the cover completely, but was able to clear the clog. My problem now is that I cannot replace the cover correctly. Is there a way to remove this cover? Thanks, Elizabeth


When you tried to remove the cover did you have to put a little force on it to get to the clog ... Vacuums

I have a Dyson DC-17 and the top of the cyclone has hair and other debris jammed in the ports. It has 6 six screws holding the parts together and I can only get access to 4 of the screws. The bottom piece appears to be removable, but I can't figure out how to remove it without damaging it. If I can get this piece off, then I have access to the other 2 screws. Can you tell me how to remove the bottom piece? Thanks in advance.


The instructions on how to dis-assemble your DC-17 are somewhat lengthy and it is quite helpful to have pictures and videos handy while you are doing it. Normally I would give the instructions here, but due to the amount of info that is necessary to ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

I have a EuroPro Infinity NV29 and I have a clog in the base. I have removed the screws and the plastic piece where it says access port to remove clogs but don't know how to get the hose lose to empty it.


... Vacuums

Model number f 5912-900 hoover steam vav with clean surge.This is not the f5914 model........my new machine has 10 min. on it...in mid use it has stopped sucking and now is blowing more than anything, I took the front clear piece off as well as the black cowling/shroud and can find no obvious hoses to un-clog nor anything else to un-clog for that matter...I am looking for advise to fix this thing now, myself


Here is a list to go by for no suction problems that you can follow along with they are common proble\015\012Problem #1 Steamvac is not Sucking!If your Hoover Steamvac was working properly and suddenly it is not sucking any ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

How do i remove the front of the Proheat Clearview to clean it out? I removed the two obvious screws at the front sides of the clear plastic part but see anything to remove to take it off.


... Bissell 1699N ProHeat Clear View Force Upright Vacuum

My steam pocket mop seems clogged. Steam does not come out of the mop head. The clog appears to be in the rectangular mop head. The triangular head still works fine. I've tried soaking it in hot water and soaking it with cleaning solutions. They have not worked. If I blow into the connection piece, no air goes through. That's what leads me to believe there is a clog. If you can help, please do. I like the product and haven't been able to use it for awhile because of this. Thanks.


I had the same issue with the rectangular mop and corrected it by disassembling the tube from the rectangular piece. There are two screws that will need to be removed in order to get access to the connector. Once the connector is removed from the rec ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I bought the vac, used, but was told there was nothing wrong with it. I called the company, and was given the impression that it will be a huge headache to return it. Here's the best part: when I received it, I opened the box: it was broken. Clearly the highest internal piece of the vacume, whent he handle is removed, was cracked off, and in two pieces. The handle will not lock into place, so if I were to vacume forward, see ya, and the vac is back in pieces. Any idea how to rig this to get it t


... Dyson DC25 Vacuum

My Hoover Windtunnel Mach 6.9 brush roller quit working. Upon investigating I found that the idler arm pulley was broken so I managed to replace that. Before putting the cover back on I see the control knob for the roller brush moves a plastic piece left or right to activate/deactivate the brush roller. I don't know where this plastic piece connects. It appears to me that the idler are when raised creates tension on the belt which drives the roller. I'm at a loss trying to figure ou


Try this link belowhttp://www.ereplacementparts.com/hoover-u6630900-windtunnel-selfpropelled-bagless- ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Clogged vacuum Rather stupidly, my boyfriend 1) were vacuuming without a bag and 2) vacuumed up a big piece of cotton from a sofa cushion. And now it's making a horrible noise and I see it vibrating where the tube connects to the machine. When you look inside there's a white thing sticking out but it looks like it's part of the vacuum. If it's a clog, how do you fix it? I tried unscrewing the tray the bag sits in but it won't budge.


You can start by taking off the bottom plate or top cover, which ever comes off, that is where the inlet starts going in and hopefully the clog is there. Could be in the hose also. But without the complete model number I can't look it up to see a p ... Kenmore 31912 Progressive Direct Drive Bagged Upright Vacuum

We have a Eureka Chinese p.o.s, model 6831. The brush roller won't turn, appears to be plugged with cat hair dang long hair cat. I cannot figure out how to remove the cover without breaking it after removing the screws, there is a u shaped collar on the tube in the way. Can anybody help?


There are a couple of tabs on both sides of the top housing that need to be unlocked by using a flat screw driver, then the top will come off. The u shaped collar on the tube will then give way to take the roller brush out to clean. ... Vacuums

I have the Miele S7280...the one without the clog hatch on the back. I took the bag cover off, then continued the remove the screws and cover underneath it to detatch the top from the bottom. Found the clog and cleaned it out. Heres the problem...now the power nozzle light comes on and the vacuum "on" is lite up red, but it will not come on. Checked the filters and the bag. It certaintly seems like the top and bottom are meeting up to latch into each other, but I have no power. Help!!


... Miele S7210 Bagged Upright Vacuum

I have the Hoover Max Extract steam cleaner. It is about 2 years old. When I turn it off a lot of water immediately leaks out the bottom and continues leaking for some time. I looked underneath it to see if any hoses appear to be disconnected, but they don't appear to be.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

** suction The best way to describe it is that when I was vacuuming I could see dust clouds at the front of the vacuum where the light is swirling around in the air. It was like it was blowing dust around instead of picking it up. I checked the tubing and found that it was clogged with some paper and hair ***** etc.... So I cleaned it out and tried it again and it still was not picking up properly. I had my husband take all the tubing apart to check for other clogging and there was none. When I


You have an airflow problem. You may still have a blocked intake or tube, also check the filter. The air is supposed to go in the bottom (of course) and I'm sure you k**w where it goes out. You probably can **te a reduction in exhaust. If this is ... Oreck XL Ultra Bagged Upright Vacuum

How do you clear a clog out of the wand? There has to be a way to remove the clog without damaging the hose.


I would push a length of stiff wire through to ease out the blockage.pete ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0481 seconds