Having problems with your Euro-Pro Shark Cordless Stick Vacuum SV775R Vacuum ?

I have a Euro-Pro Shark Cordless Sweeper Model UV610. The motor still runs but the spinning brushes are no longer spinning. Can someone that is familiar with this appliance please assist me at repairing it and/or what parts I may need for repairing it? Thanks T.R.


Answers :

IT SOUNDS LIKE YOU HAVE A BROKEN BELT, THAT CONNECTS THE MOTOR TO THE ROTOR BRUSH.
Repair Help & Product Troubleshooting for Euro-Pro Shark Cordless Stick Vacuum SV775R Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Euro-Pro Shark Cordless Sweeper Model UV610. The motor still runs but the spinning brushes are no longer spinning. Can someone that is familiar with this appliance please assist me at repairing it and/or what parts I may need for repairing it? Thanks T.R.


IT SOUNDS LIKE YOU HAVE A BROKEN BELT, THAT CONNECTS THE MOTOR TO THE ROTOR BRUSH. ... Euro-Pro Shark Cordless Stick Vacuum SV775R Vacuum

Our Winsdor Sensor XP12 does not show any power or lights, I did check the handle connection, it was fine. The power cord has been repaired with duct tape 3-4 x where someone has sucked up the cord, this may be the cause yet it ran fine last time it was used! so I am at a loss, please help if possible.08/31/2010 Steve


Any time the cord has been damaged badly enough to require taping, the possibility or intermittent "opens" exist. This means the wires are in contact much of the time, but will losed contact periodically. Even if it worked fine seconds ago, jigglin ... Windsor SR12 Sensor Bagged Upright Vacuum

VACUUM REPAIR I have a Hoover Savvy upright, windtunnel, bag/bagless vacuum (model U8150-900). The Handle Release Foot Pedal - Part #38434026 broke soon after purchase but I finally found a source to replace this item. The problem is that now that I have the repair part I cannot figure out how to remove the old pedal and install the new one. The housing appears to be one piece of solid plastic. Any ideas, PLEASE! Peter


There are 2 tabs that stick out on the release, they fit in slots, so from the top look down and you can see them, using a flatblade screwdriver that will fit in there, push the side in to release it, which isn't easy, but it can be done. When you g ... Vacuums

The brush on my Kenmore Pet Power Mate no longer spins. I opened it up and found the problem may be with the rubber band connecting the spinning parts. Where might I purchase a new rubber band for it?


Try this link > http://www.vacuums24x7.com/kenmoreparts.html ... Vacuums

Hi, The thermostat on my PoltiVaporetti (1300) is not working. I can't find an appliance repairer in Brisbane, Australia. The repairs haven't got means to access problem spots and cite no way of getting possibly needed parts.


... Polti Vaporetto 2400 Canister Steam Vacuum

I have a Fantom 500 DX and it seems that it doesn't pick up anything anymore. It looks like machine is working well, but it doen't pick up. I would like to take to the repair guy, but I don't know where to find one. Machine is good, it might need jsu some maintenance. Please advise. I live on Long Island, NY. PLease advise. I changed the belt about 6 months ago, but all other parts are original.


The type of bagless that has sharp turns in the hose and plastic parts are easy to become stopped up. You have to follow the path of the air flow to find the blockage. ... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

Please tell me why I should consider buying a dyson after 4 years mine has had to have new parts and now it is totally beyond fixing. So many parts have broken off of it and I can only use so much duct tape to repair. I need a new vacuum but I am very skeptical to invest again in a dyson.


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Problem with cord rewinding mechanism on my Nilfisk King!Whilst repairing broken cord(successfully)the metal coil thats part of that mechanism sprang out!Can someone out there tell me how to put it back together again PLEASE.I would so like my cord to be able to retract again


... Vacuums

I have an Alba Vacuum Cleaner model AVC1502(Bagless cyclonic cylinder 1500w) I am in desperate need of a filter cover. As I have severe arthritis this vac cleaner only weighs 5.1kg(not able to lift much weight) please I need help tracking down the filter cover, perhaps a later model may have the same cover, need all experts assistance thanking you sincerely for any help that can be offered. In anticipation Dee


Www.searspartsdirect.com ... Vacuums

I have an Alba Vacuum Cleaner model AVC1502(Bagless cyclonic cylinder 1500w) I am in desperate need of a filter cover. As I have severe arthritis this vac cleaner only weighs 5.1kg(not able to lift much weight) please I need help tracking down the filter cover, perhaps a later model may have the same cover, need all experts assistance thanking you sincerely for any help that can be offered. In anticipation Dee


... Alba Vacuums

Hi good day, I have a Kenmore Grab n Go 12.0AMPS Vacuum cleaner, Model# 116.34722402 & serial#T53601507. The vacuum is now having a problem whereby the rolling brush underneath is not spinning when the vac is on. This has caused it to stop sucking up dust. Could you please advise as to what might be the problem. Thanks in advance for your kind assistance. regards, Clarance


... Kenmore 34722 Grab-N-Go Upright Vacuum

I need an operators manual for the bissell model #1631 please, and a parts list. I may be missing something when I purchased it at a yard sale.


I believe you will find what you need at this URL:\015\012\015\012http://www.bissell.com/product_search.aspx?searchtext=Bissell%25201631%2520PowerSteamer%2520ProHeat%2520Canister&searchType=search&mode=userguides&pagesize=25\015\012\015\0 ... Bissell 1631 PowerSteamer ProHeat Canister Vacuum

I have a Hoover Deluxe Spin Scrub carpet cleaner that has lost suction. I read the solution by Chris Jones of GoVacuum.com, in which he described the design flaw whereby the tool attachment hose tears at the point of connection with the motor housing. That is the case with my machine. Now I just need to know how to repair it. What kind of tape can I use? Plumber's tape? Please help me!!!


A tear in the hose will only affect pick up through the hose when using it to clean furniture, stairs, and such. It will have no effect on the carpet cleaning operation. If the hose cannot be replaced for a while, black electrical tape is one solutio ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a DeLonghi coffe urn Model # DCU61. It leaks terribly during the brewing cycle. I believe I broke the seal. I tried to unscrew the glass knob on the cover to clean it and discovered it didn't screw on! Please help me. I can't seem to find an appliance repair that will fix coffee urns.


HelloFirst locate where the leak is coming from,Leaks in pump coffeemakers are often due to faulty tube connectors. Unplug the coffeemaker and fill the reservoir with water. If water leaks from an elbow, clean the mating surfaces before r ... DeLonghi Vacuums

I can see the height adjuster under my Bissell pet hair eraser vacuum, but it doesn't adjust. The parts don't look like they're touching. It's been iffy since I took it out of the box. Now it doesn't adjust at all. Used only five times. Looks like I should be able to fix it myself. No local repair available. Could you help please?


Http://uk.bissell.com/images/UserGuides/3920E_508.pdf\015\012\015\012This is the pdf manual. If you look at page 12 you'll see that the bo ... Bissell Vacuums

I have a bissell powerlifter carpet and upholstery cleaner purchased in 2000-2001 by my wife. the sprayer does not work, it appears that the liquid is not being pulled up out of the tank. i am wondering if there is a part missing from machine. something that may need to go into the main tank. please advise.


I knew someone who had a problem with bissell before. I think they had to take it apart and clean the hose, dirt could be clogging it. Or you could try contacting the company. ... Bissell Vacuums

My hoover windtunnel is not picking anything up all of a sudden. Also the roller underneith is not spinning. I've replaced filters and the attachment part is working fine, just when it's in the upright position it won't pick anything up. It also doesn't seem to be self propelled anylonger either. It use to **** everything up, including the dog. Please help!


The belt that drives the brush roll has broken. That's why it doesn't pick up and why it doesn't pull itself forwards. Check the User Manual (download from Hoover website if necessary) for information on replacing the belt. Good luck! ... Hoover U6630-900 WindTunnel Bagless Upright Vacuum

Don't want an expert. I wan someone with authority that can make an intelligent decision regarding the way you sell replacement filters. It looks as though the patients are running the ward at HQ. This freak insane! Maniacal and just plain stupid! Tell me something Mr Expert, my closest choice was "vacuum expert" How is this expert going to know and fix the asinine way b&d devised a plan so that the consumer would enjoy wasting a better part of their day. Who, please tell me, who with a drop of


Ouch! So go into Lowes get a 10 pack of electrostatic register vent filters back in the furnace filter section. Take your old filter off and if it's a paper corrugated looking cone just wash it really good and dry it out...if it's disintegrating then ... Vacuums

I have a White Model 258SM sewing machine and when I have all the settings set for straight stitching, the needle bar still moves side to side. Is there something that I am doing wrong or is this normal and I just don't remember it happening before? Thank you for your assistance. If repair is needed, can you recommend someone in the Brainerd, MN area?


... Vacuums

Problem: water will not dispense Local repair shop gave verbal diagosis>need both solenoid valves. Found this part on www.nelsonappliance.com $14.95 each. (Shop quoted $98 for repair & parts) Can i access & replace parts? Is there a "how to" video available?


... Bissell 9200 Upright Vacuum

I have a riccar 500 upright and the axel broke in half. The repair shop says it cannot be repaired without replacing the part. WHere can I get the replacement part?


The repair shop should have all the parts needed. However, sometimes the manufacturer stops making some parts. If this is the case, you may need to try to find one at a thrift store or garage sale and cannibalize it. ... Riccar 8955 Upright Vacuum

Have Hoover F7452900 spin vac carpet shampooer and brushes won't spin. The screen by the brushes is clean and they are place in position to clean on carpet. I noticed that when I have the brushes out of the machine and turn it on that the white square that is on the base of the machine does not spin--this is where part of the brush connector fastens to make bristles spin.


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

Lost Part I have a 6.5 hp 18 gallon shop vac ultra pro. There is a part that goes into the inside of the tank and screws into the collection hose that attaches it to the tank. This part accidentally got thrown away when someone dumped it and now I cannot attach the hose to use the vacuum. Can this part be purchased separately?


I found a manual online for the shop vac and found the part number. Did locate part online.\015\012Thanks, ... Shop Vac Vacuums

Shark Euro-pro EP621 Bagless Upright Vacuum. Q regarding the brush not spinning / after troubleshooting and taking actions listed below, it now spinning for a few secs, but then stopping. Already removed hair, strings, etc. Checked that belt is aligned properly, checked that small wheel that turns belt is working (spins fine when belt removed. Oiled the turning parts a bit, that made it spin better, but still stops. It turns about 3-4 seconds then stops. If I switch it off and on again, I get ag


... Euro-Pro EP621 Bagless Upright Vacuum

I have a Eureka 5902AVZ and the brushroll does not work. when i remove the belt, which is not torn nor worn out, the motor spins perfectly fine. Though when i put the brushroll back into place, it shows that the motor is trying to spin, but with resistance. it seems the brushroll will not spin if locked into place, because there is no attachment on the left side of the brushroll that will allow it to spin freely with the belt. am I missing some parts or is there something else wrong?


Hi and welcome to Fixya. I am Kelly. \015\012\015\012You have correctly identified the problem as the brush roll itself. \015\012\015\012There is a bearing under each end cap of the brush roll. You can gain access to the ... Eureka 5902AVZ Bagless Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0621 seconds