Having problems with your Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum ?

Took apart the s3101 and there is a long spring inside..where's it go. It's not obvious


Answers :

Hi,

The long spring goes over the plastic tube that goes to the head to support the tubing...

Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...

Euro-Pro Shark Steam Mop Problem

Here also is a link to get any of the Shark Manuals that you need.

heatman101
Repair Help & Product Troubleshooting for Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Took apart the s3101 and there is a long spring inside..where's it go. It's not obvious


Hi,The long spring goes over the plastic tube that goes to the head to support the tubing...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Long spring S3101W Took apart have a long coil spring where does it go


Hi,The spring goes on the hose to give the plastic tubing some support...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a Kirby Generation 3. The handle spring assembly is broke, so I took it apart to get a part number. Can you tell me if there is a cross reference or something on these parts. I am unable to find a part with the same number that is located on the part I took off. The number on this spring assembly shows Kirby HA-670289B K-1. Any help finding this part is appreciated.


... Kirby Vacuums

I cannot charge my two year old electrolux pronto. I purchased a brand new hand held vacuum for it, but even the new one does not charge. When I plug in the cord nothing happens. If I turn on either the long handle or the portable unit within the long unit, the blue charging light comes on for a few seconds, then out. This tells me that the circuit is intact without a broken wire somewhere. I took it all apart carefully and could see nothing broken or out of place. On re-constructing it, it


It must be the charging transformer. We have already ruled out the vacuum unit. Unfortunately the transformer is not a serviceable part, and will need to be replaced. ... Electrolux Pronto 2-In-1 Stick/Hand Vacuum - Cayenne

The Lower body of the Bissell QuickSteamer, water pours out from the body. Solution: I took apart the machine and there is a spring loaded valve with a rubber washer at the bottom. Think of the letter T upside down with the rubber washer on it. The washer stretches over the bottom and the spring creates a leakproof plug and won't allow water to pass till the button on the handle is pressed. This old washer came partially off and allowed water to leak. I purchased from the plumbing dept. a mi


... Bissell Vacuums

I fear the motor has failed on my Electrolux Oxygen EL6988D. Just six months after the warranty expired, I was vacuuming when it suddenly stopped. There was no blockage in the tube and it wasn't working hard or long . . . it just stopped. I looked around the Internet and it appeared that many similar Electrolux units have a fuse. I hoped my problem might just be a blown fuse, so I took the machine apart. There are two small printed circuit boards, but no fuse. There is an in-line


Hi,\015\012\015\012I don't think you need a new motor, but please stop testing the machine with live power. It's dangerous and unnecessary. Your tests indicate to me that the motor is fine and your thermal-fuse - I think this is wh ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

TOOK MY ELECTROLUX EPIC 6500 CANISTER MODEL 1762 APART TO REPLACE CORD REWINDER. TO MAKE A LONG STORY SHORT,MOST OF THE WIRES CAMES OFF OF HEIR CONNECTIONS. NOW CAN'T FIGURE OUT WHERE THEY GO WITHOUT A SCHMATIC. CAN ANYBODY HELP. THANKS CATHY


Hi,\015\012\015\012I will try to find a service manual for you. ... Vacuums

I am trying to replace the power cord for my 82 year old father-in-law's Oreck XL 2600HH. He already took it apart. I need to know where the semi U shaped spring steel piece is supposed to go inside the Helping Hand Handle? Any drawings or schematics available? Thank you for your time. Arthur


That justs lies on the inner handle whenb you put the spring back. There should be two holds where each end of the spring sits in. ... Oreck XL Ultra Bagged Upright Vacuum

The height adjustment on my Bissell 6594-W no longer works, I took it apart and reassembled but still doesn't change the height. Should there be a spring in there? Is there a site with directions on how to fix it? Thank you.


... Bissell 6594 PowerForce Bagless Upright Vacuum

I HAVE A FANTOM VACUUM CLEANER MOD.#F1205400. I PURCHASED IT ABOUT 6 OR SO YEARS AGO.IT WORKS PERFECT,AS FAR AS SUCTION, THE ONLY PROBLEM IS ABOUT 2 MONTHS AGO,SOMETHING HAPPENED TO IT AND IT GOT VERY LOUD, KIND OF LIKE A CAR WITHOUT MUFFLER. I TOOK IT APART,AND FOUND NOTHING OBVIOUS. CAN YOU GIVE ME SOME IDEA OF WHAT I CAN CHECK TO RESOLVE THIS PROBLEM. AS I SAID BEFORE IT STILL VACUUMS GREAT. THANK YOU, VINCE


You probably have a bad motor bearing. I don't know if the motor is available now or, these older Fantom's are obsolete along with most of their parts. ... Vacuums

I took my dyson animal dc25 apart at the kick stand and a spring came off


Hi there,Since your issue will be difficult to rectify on this page, please get in touch with us free, on 08002980298 (UK), or 1866MYDYSON (US), so we can provide the help you require.Kind regards,JackDyson C ... Dyson DC25 Vacuum

Hoover model U6476910 I was cleaning out the bearing sections of the brush when a spring type pressure washer fell on the floor. I did not see the washer when I took it apart and I can't tell where it goes in order to put it back together. It is very thin and measures about 5/8 inch with an 11/32 inch hole. Frank Nething


Hi frank this sounds like its a compression washer, you normally find these on the end of the roller to even out any movement from side to side, as you look at the hoover's brush head, it should slip into a groove on one side with the roller...hope t ... Hoover Self-Propelled WindTunnel Bagless Upright VacuumVacuum

Bissell PRO Heat Steam Cleaner is not dispensing the water. I took it apart and cannot find any obvious issue with it i.e loose tubes, connectors etc.


Does water squirt out of the hose nozzle, if it does, then check the heater inside the handle asm. Make sure that where the tubes hook up to it are not clogged. If water doesn't squirt, check for the seal at the bottom of the tank, it needs to be o ... Vacuums

I took my Dyson DC 25 Animal apart to clean it, and now the red foot pedal won't lock the vacuum into the upright position anymore. The trouble is the spring pin for the pedal popped out and I can't figure out where it is supposed to go.


That spring thing goes where the pedal screws into the side. When 'facing' the dyson in the front, it's on the left side. The spring's circle part and short stem section goes into a divot area on the pedal. The other end is tensioned (braced) a ... Dyson DC25 All Floors Bagless Upright Vacuum

My sister dropped her roomba than brought it to me complaining it does'nt work anymore. I took it apart, cleaned everything i knew to clean,could not find anything obviously wrong so I put it back together.I charged the battery than tried it. The green light comes on when you push the clean button and it makes a little grunt noise but that's it.


Have a look at the motor brushes if there broken or poped out this is were the "grunt is coming from" the motor is trying to turn but cant? ... iRobot Roomba 4000 Bagless Robotic Vacuum

Bissell 7901 Proheat Carpet cleaner water will not come out. Everything else works but it just will not wet the carpet... I have took apart the handle n I do not know where to put the spring back. Please Help


... Vacuums

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b


... Vacuums

It works well until it bumbs a wall. When it backs up it will not go forward again. I took it apart and noticed a cable is lose. I dont know where this cable hooks up to. One end is on a plastic disc on the end of the motor. The other end looks to have been pulled lose from somewhere. Its only about an inch and half long.


... iRobot Roomba 560 Robotic Vacuum

The kick stand that lowers the vacuum when in use got in a position where the red foot pedal would not come back up to bring the wheels down and the vacuum rest in the upright position. We took it apart and corrected the position, but the side with the small circular spring came out and we are not sure how to attach it back, exactly where it hooks onto. Can you help show us where it goes?


... Dyson DC25 Animal Bagless Upright Vacuum

My Hoover Windtunnel dual v brushes quit turning ....I took it Apart but I see no obvious problems. How can I fix it ?


... Hoover U8126-900 Wind Tunnel Dual V Bagless Upright Vacuum

Spray doesn't work on my Bissell Proheat 2x 8920 took apart but couldn't find where the heater is


It's in the handl ... Bissell Brushroll Proheat 2X 8920 9200 9400

The powerbrush seb 217 on my miele red velvet stopped spinning yesterday and the red & yellow lights came on the head. I took it apart and there are no strings clogging. It appears that the gears doesn't spin anymore. Took it apart and cleaned the contacts. still no luck. is it likely it is the motor?


... Miele Red Star Bagged Canister Vacuum

My Eureka Altima vacuum the brush is not spinning. I took it apart and the belt is Not broke, but when I turn the vacuum on I can smell the motor overheating. I turned the machine off and unplugged it and then took it apart so I could see the underneath and plugged it back in and the belt still won't turn..can you help?


Hi, since you have detected the the smell of the overheating motor, then the motor is faulty which is why the belt is not turning. You should change th motor ASAP........... ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

Rainbow Hi: I took my unit apart to clean it. I was careful to put it back exactly as I took it apart. Now it won't start. I also need a new filter. I rinsed it out but it still stinks.


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=19674&thid=779655\015\012Rainbow\015\012Posted by Nat51 on Jul 13, 2008\015\012Hi: I took my unit apart to clean ... Rainbow E series Canister Wet/Dry Vacuum

I have the Sharper Image EV-HD15 Cool Mist Humidier Ultrasonic 1.6 gal humidifier. I purchased it last year. Yesterday I took it apart to clean as per instructions. I feel that I may not have place the round housing (which is secured with 4 screws) back correctly. When I turned the machine on it made a whirring sound. I took the unit apart again and rotated that round piece moving the opening away from the opening on the tower. The whirring sound was reduced but there was still a sou


... Sharper Image Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0401 seconds