Having problems with your Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum ?

Engonmic hand grip broke off

\015 My shark steam mop was resting against my wall & fell over onto my ceramic tile floor. When the mop hit the floor the handle broke right off leavinga small piece inside the upper extension tube. Can these parts be replaced ? I hope so, I really like the shark steam mop but very unhappy that just falling over onto the floor would snap the handle off that easily. \015\012\015\012Thank you\015\012\015\012Jeanmarie Serafine\015

Answers :

The solution is to send me a new mop. Shark S3101 Eur Pro Shark Steam Mop free of charge and free shipping. I do not think I will be buying anymore Shark Products. Thank you. Harry R. Simcox #46 Rolling Hills Rd. La Luz, NM 88337 or PO BOX 157 La Luz, NM 88337
Check the manuals link and maybe they will replace it under warranty...

Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...

Euro-Pro Shark Steam Mop Problem

Here also is a link to get any of the Shark Manuals that you need.

Repair Help & Product Troubleshooting for Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Engonmic hand grip broke off

The solution is to send me a new mop. Shark S3101 Eur Pro Shark Steam Mop free of charge and free shipping. I do not think I will be buying anymore Shark Products. Thank you. Harry R. Simcox #46 Rolling Hills Rd. La Luz, NM 88337 or PO BOX ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I just bought a used euro pro steam shark model ep903, has all parts but when I turned it on to use it water and steam poured out of the handle grip area. Am I not doing something right? The manual says to attach the brush directly to the hand grip but I can't use it without getting burned. Any suggestions would be greatly appreciated! Thanks!

... Euro-Pro Ultra Steam SharkTM II Hard Surface Steam Cleaner Vacuum

Hose hand grip

... Electrolux Centralux Vacuum

Needle rubbing I have a singer pro finish and recently I broke a needle and the lower looper also busted clean off. I ordered the lower looper and replaced the broken one and changed both the needles. Now when I turn the hand wheel and the lower looper moves to the left and the needles descend they pass in front of the looper but when the needles begin to move up and the looper moves back to the right the needles bend back and go behind the looper. Help! Thank You!

... Singer 14CG754.CS Pro Finish Industrial Commercial-Grade Serger

My dyson vacuum brush bar will not rotate and the belt is not broke. The hand tool works fine. What is wrong?

I took the plate off and cleaned up the vacuum brush bar. Since the belt was not broke I knew that was not the problem. I know when the setting is bare floor, the brush bar will not rotate. That was not the problem. I just keep turning the knob f ... Dyson DC15 All Floors - The Ball Bagless Upright Cyclonic Vacuum

I have the same rproblem with my little Shark V15Z hand held vacuum. the belt broke,there's no instruction on how to replace (and apparenlty it was not designed to be replaced (at least with out a lot of research). I see BElectric describes how to find the hidden path, but now where can we buy the correct belts??

... Euro-Pro HEPA Shark EP035 Bagless Handheld Vacuum

The belt broke, and I can't find out how to get a replacement (Shark Hand Held Euro-Pro Model V15Z. Help!

... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

We have a Eureka 71B Hand-Held Vacuum and it looks like the belt broke. I removed the two screws at the bottom that should release the housing that holds the belt. However, the housing still does not come apart. Any advice? Thanks.

There's a 3rd screw hiding underneath a plastic shield. You'll have to drill or cut off the covering but then it's pretty easy to deal with. ... Vacuums

Hoover U4395 Vacuum fan (impeller) broke

I've done these impeller replacements on two different Hoover convertibles.Yes it's a left handed thread on all classic convertibles - loosen it clockwise (reverse thread)After getting married, my wife upgraded the vacuum to one of th ... Hoover Vacuums

Hoover linx cordless bh50010 wire broke on motor can I get the part and fix it myself

... Vacuums

Rug doctor hand tool will not spray ...but it will vaccum....what can I do to get the hand tool to spray again ....tried another hand tool and that didn't work either ....help

... Vacuums

I have a Hoover SteamVac F5914-900 SpinScrub... The last time I used the hand tool attachment, it worked fine. Just tried to use it again, and now I only drips of water will come out of the hand sprayer, if that. I have tried prepping it for up to 15 seconds like the manual says... no luck with that. Also it is making a big puddle on the floor, probably because the brushes on the main unit keep spinning when I am trying to use the hand tool which I dont think they are supposed to do? Can a

The brushes can be turned off on most of them via a switch on the hood. There shouldn't be water coming out onto the floor unless you are pulling the trigger at that top. You probably broke this when attempting to use the tools. ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I dropped my battery operated alarm clock: the second hand still works but the alarm doesn't come on at the set time and the hour & minute hands don't "hold" their position - I took the clear front off and discovered that I could move the hands to a more secure place on the center spindle but I discovered during the night that the correct time was no longer showing. I really like this clock b/c it's battery operated and I can hear the alarm (when it worked) plus it has a "night vision" dial tha

The hour and minute hands can be pushed onto their respective shafts at any point in most clocks.\012If you already know the time that the alarm is set, let the clock run until it sounds. \012When the alarm sounds, install the hour hand a ... Vacuums

I have a Bissel 9300-C 0714 BC Carpet Shampooer. It was working great and all of a sudden it stopped working. It still sucks up dirty water but it does not spray water onto the carpet. I can get it to spray water through the smallest hand attatchment but not through the large hand held piece on the base of the machine. I really hope you can help me, I am a dog groomer and I really need my machine to work properly. I can get it to spray water out of the smallest hand attatchment but that's all t

The spray jet has become clogged from the soap.... just clean it out. same thing happened to my attachment. ... Bissell 1699 ProHeat Clear View Upright Steam Vacuum

I have checked for clogs in all of the hoses. When I take the hose and my hand over it, it sounds and feels like it is going to **** up my hand, but when I put a piece of lint for it **** up, it doesn't the lint is still in my hand. What is causing it not to **** up the dirt and lint?

Hi,\015\012\015\012Have you cleaned or changed the filter??? \015\012\015\012That is my first thought... the filter is no longer working correctly and allowing enough air to go through it...\015\012\015\012 ... Kenmore Progressive Bagless Upright with Inteli-Clean SystemVacuum

The belt broke on my proheat, I got the replacement belt and got it put on, turned on the machine and it instatly broke the new belt. Any ideas why??

Sound like brush roll is jammed solid .Clean. ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Hoover platinum carpet cleaner. won't extract the water out of the carpet... ever since I used the hand held extension. I have tried unplugging, resetting the hand held part... i have all this water in my carpet!!!

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha

I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I have a Beam Rugmaster Plus power head Model BM1 393 Type AB and the connection were the metal pipe meets the plastic swivel broke close to the unit. It appears like a manufacture defect in that is broke in two small places and not the entire unit. Can this piece be replaced or glued??

This is most likely repairable. Lots of the Beam parts are available. I would recommend checking out any local vacuum shop or searching online for a central vacuum store that sells beam products. ... Beam Industries 750 Classic Bagless Central System Cyclonic Vacuum

I got a Dirt Devil Versatile 3 in 1 design hand vaccum for a birthday present This has a suction type of cleaning. I would like a hand held lightweight vaccum cleaner with a roller type brush and cervice tool. I would like to clean carpeted steps. I want to return the above cleaner and get a voucher for another cleaner.

... Dirt Devil Vacuums

Our belt broke and now i can't find out where it should go back! The second one broke too so I thought that maybe I was putting it in the wrong location>

Check the brush make sure the ends spin freely if so put the belt on spin the brush with your hands 3 or 4 times around the belt will seat its self ... Vacuums

I have a new Euro-Pro shark model S3101. Used it one time and while I was doing my tile floor in my kitchen I reached under a cabnet to clean and hit the floor kick kind of hard and broke the head off of the shark. I have only the T shaped end on the shark now with the cleaning head broken off and looks unrepairable. I did kind of hit the floor kick hard but the plastic broke like glass. Can I put a new head on the remaining piece or is it repairable? thanks Angie

Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Pro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Just got secound hand ....hand held shampooer where to put water and how to put back on machine for use

... Dirt Devil Vacuums

My electro lux pronto hand vac works but not the sweeper. As long as the hand vac is out of the stick it works but not when placed in the stick

... Electrolux Vacuums

I have the Bissell Proheat (7901) It will pick up water and the hand tool works fine. I noticed that the red indicator stopped spinning. Then I noticed no water was coming out. If I put down water using the hand tool, the vacunme will pick it up. When I called Bissell they had me do something with the indicator. When it didn't work they said take it in for repair.

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0309 seconds