Having problems with your Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum ?

I have a Euro-Pro Shark Steam Pocket Mop. I used it twice last year, and then it stopped producing steam. Is there any way that I could easily fix this without dangerous chemicals? Everytime I call the company, I can't get anyone. The unit heats up, but doesn't produce steam. I've tried white vinegar to no avail. I am afried of using clr after reading that the unit blew up on somoone. I am visually impaired.


Answers :

Hi,

Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...

Euro-Pro Shark Steam Mop Problem

Here also is a link to get any of the Shark Manuals that you need.

heatman101

pp
Repair Help & Product Troubleshooting for Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Euro-Pro Shark Steam Pocket Mop. I used it twice last year, and then it stopped producing steam. Is there any way that I could easily fix this without dangerous chemicals? Everytime I call the company, I can't get anyone. The unit heats up, but doesn't produce steam. I've tried white vinegar to no avail. I am afried of using clr after reading that the unit blew up on somoone. I am visually impaired.


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

There is a break in the cord where the clamp is entering the unit of our Majestic IAQS system Filterqueen Lux have tried to get into it but cant seem to get it open! Any ideas?? This unit is approximately 5 years oldish!


Undo the side clamps so that you can get to the dirt below. Grab the handle and remove the top portion of the canister. Take the top portion and to go the table. Remove all the attachments (if they are even attached). twist an ... Filter Queen Majestic Canister Vacuum

I'm trying to get my S7000 Miele to stand upright an lock in this position. It wont , i tried to see if foot release was jammed but cant tell it doesnt seem to release to let it move upright an lock in again..help


There is a rear dust cover that sometimes gets stuck, this will make it almost impossible to lock the handle up. First locate the cover which is at the rear right above the wheels. It's about 2"x8" and ribbed vertically and slides up behind the rear ... Miele S7210 Bagged Upright Vacuum

I have a new (couple of months) Cuisinart Espresso Maker EM-100C. One has to turn on the power button on the front in order for the unit to heat the water. The button will only work if the two manual knobs are in a certain position. Very occasionally, it took a few tries to get the button to turn on. Now it usually does not work but will once in a while. Any ideas what we could do to repair this problem?


... Vacuums

Over heating Light Comes on as soon as I try to turn the unit on. I have a Miele S558 Silver Moon vacuum that has only been used once and it shut off and will not come back on. The overheating light comes on as soon as I try to switch speeds on the handle or turn the unit on at the canister, and the vacuum will not run. Do you have any idea what the problem is?


... Miele s558 Silver Moon Vacuum

Plug the unit in, the power light doesnt illuminate and heat element doesnt heat the water. wall plug has power, mop cord isnt damaged


Mine too ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Have a Shark steamer. Tried the vinegar, tried the CLR, tried putting a piece of wire and a skewer into steam hole...no luck. The unit gets hot but no steam. Will try one more round of CLR and let it sit overnight. Other than all that I mentioned...have no idea what to do next. It's a great gadget if it worked!!


\012\012\012Hi,Here\012is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it\012may not be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

November 2008 I bought a Simac Stirella 9000D steam generator iron. Recently its been leaking water out the bottom of the regenerator. It makes a noise when it is trying to get the steam to the iron and it works then but afterwards when the noise stops it stops steaming and I find a puddle of water underneath the regenerator. Also a little steam comes out of the water tank at the top. I understand this is happening because of scale in the base unit. Can I get something to get rid of the scale? -


... Vacuums

Have Fresh Aire 2.1 about 4 years was running great then went dead. I cant find where the fuse is and have unit apart. I plug in no fan dim display shows to errors. Unit was pretty dirty at the time. I need schematic and suggestions. Also need to knpw how to remove the honeycomb from the light unit to check for blown bulb. Seems brittle and I could break it with trying to pry with augur or sharp screwdiver object.


I'm sorry this may only be a partial help. But fuses are usually very close to the motor, OR where the switch is located. Pretty easy to find by testing but you have to be or so careful you dont electricute yourself. Now if your testing shows v ... Vacuums

The water dispenser must have been left plugged in and the hot water switch on without any water bottle on the unit because a plastic part inside got warped and now the unit tries to heat the whole 5 gallon jug of water. I want to replace the inside plastic part but I don't have the manual and don't know which part no. to request or where to send my request for parts.


Please state the brand and model number of your water dispenser, so I could give you the exact part and lead you where to purchase it.Post back ... Vacuums

I am trying to replace the cable and actuator on a Hoover windtunnel self propelled vacuum. but I cant get the top or hood off the get to them, I have removed all the screws I can see, roller, belts..what am I missing?? thanks so much for any help


Hi there SmartAlec from NelsonVacuums.com.au here. You will need to remove the knobs for carpet/hard floor selection and the carpet height to remove the cover they act as k ... Vacuums

Tried to take roller brush out to clean it's housing, cant get one side back in without trying to force it.


The roller brush fits snug in the housing, however, if you had it out, check to make sure the end caps of the brush shaft are pushed all the way on. These just slide on the roller bar shaft and if something got under them, they would not be able to ... Dyson DC07 Bagless Upright Cyclonic Vacuum

To : admiralstopf I have a U-Line clear ice maker UCLR2060B40. The authorixed service center has been trying to fix my unit since October to March. They have replaced the circuit board 2x and the Thermister and rain tube. They clai they were able to get it to work on their bench (not sure if true) but they can not get it to work in the house. They gave up and refunded my payment. Now what? Jonathan


Unfortunately we are not affiliated with any manufacturers. What I would do at this point is to contact the manufacturer of your ice maker and let them know what has transpired when you attempted to have their authorized repair center fix your issue. ... Vacuums

I NEED A TELESCOPIC HOSE FOR MY PHILIPS EXPRESSION HOOVER, WHERE CAN I GET THIS MY HOSE PIPE IS BROKEN AND I HAVE TRIED TO GET A NEW ONE AT VARIOUS SHOPS HERE IN IRELAND AND I CANT.


Hi - greetings from Scotland!\015\012Im not sure if you mean telescopic hose = do you mean telescopic metal tubes? If so they are readily available on ebay.co.uk I buy from many sellers on there but Hoovermania are one of the best. \015\012\015 ... Philips Vacuums

On our Hoover U6445-900 (Mach 6.9) we replaced the small belt that goes to beater brushes in front of unit. Upon starting, the Hoover quickly got hot and smoky. We shut it off and looked things over carefully, but the second try also resulted in friction heat on the belt. Now it appears the belt may have stretched due to heat and the brushes won't spin. Any ideas?


Are you sure you purchased the right size belt..the friction you speak of is usually caused by a belt not being the right tightness or a jammed beater brush ... Hoover U6446-900 WindTunnel Bagged Upright Vacuum

Cant get the belt to pick up on the hook when trying to get the head attachment working


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=844275\015\012Generic problem for all Vacuums\015\012Can’t get the belt to\015\012Posted by jltbo ... Vacuums

Unit not working to heat water--cant hear compressor starting up like normal


Did you make sure that it was closed all the way? Sometimes if the water canister is not on all the way it can cause this. And depending on how old the steemer is maybe that part went out. But I would check all the lines to make sure nothing is clogg ... Vapor Professionals TR6 Canister Steam Cleaner

Cant get cover back on Bissel Pro Heat


... Bissell 8910 ProHeat Clear View Upright Vacuum

Euro-Pro X model SC410. Unit heats water but when I push the power button, it just hums.... Where can I get it repaired? or does someone know what type of tool is needed to unscrew the screws on the machine?


... Euro-Pro S3325 Handheld Steam Vacuum

Kirby g4 i cant get the belt back on try and still wont work ? can u help me


First things first...take the powerhead off of the front of the kirby. If you look at where the powerhead connects to the front of the kirby and you'll see a large hook...turn the hook using the crank on the front of the powerhead so that the belt is ... Vacuums

Shutting off my vacuum has been shutting off in middle of use and i dont know why its like its over heating and i cant use it again for almost an hour is there a solution to this? or do i need to get a new vacuum?


It has a built-in temperature sensor which prevents it to be damaged from overheating. That's why it shuts down. It just needs to be opened up and cleaned thoroughly. Start with the hose if it has one and let someone who is handy with electric applia ... Vacuums

Hi there ive just purchased a bissell 1623e but cant get the 1 of the 2 screws to line up and tighten in handle any tips? ive tried holding it at all angles pushing down pulling up still it wont tighten should i take it back to shop? as faulty?


Take it back as faulty no question about it should line up easy and screw in stright away ... Bissell Carpet Cleaner Powerbrush Deep Cleaner Vacuum

Shopvac 90L400 quit working (4 years old). Thought the switch was bad but not the problem. I read that there is a fuse link in the motor that frequently burns up. I tried to take motor apart but not sure of the process. I was able to get to the motor but cannot pull it out of the armature. It appears I have to take the aluminum blower unit off the shaft (it appears to be pressed on with a retaining washer). Do I have to take it off to pull the shaft and motor assembly out? Is that where the fuse


By pass the switch and take power right to the motor leads.. that should tell you if the motor is ok.. have not seen fuse link on a vac motor.. graingers has new motors, but not inexpensive ... Vacuums

How do I get to the heating element to clean it for my bissell pro 2x? I have tried everything else.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Shampooer I have a rainbow e series and my shampooer is not working. The tubes do not seem to be clogged and it sounds like it is trying to work but we cant get the water to come out. We pull the trigger and nothing no soap, no water, nothing. Can anyone help?


Aqua mates have an o-ringed valve assembly that go bad regularly reccoment having it replaced by local vac shop ... Rainbow E series Canister Wet/Dry Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0786 seconds