Having problems with your Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum ?

When I attach my rectangle head ,steam will not come out, then when I take it off steam goes everywhere. It looks like something has melted in it.


Answers :

Hi,
You need to clean that hole out...


Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...

Euro-Pro Shark Steam Mop Problem

Here also is a link to get any of the Shark Manuals that you need.

heatman101
Repair Help & Product Troubleshooting for Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

When I attach my rectangle head ,steam will not come out, then when I take it off steam goes everywhere. It looks like something has melted in it.


Hi,You need to clean that hole out...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a Series G Kirby Model G7D. The other day when I was vacuuming all of a sudden the TechDrive (Power Drive Assist N/D) pedal fell off. I see the hole that it goes into but when I put it in it's loose and falls out and doesn't control the power drive anymore. When I shook the vacuum I heard something rattling around inside the vacuum head. So I unscrewed the bottom and looked inside and found a small metal part labeled K3 on one side and T on the other side. It looks like it would fit


Hi, I have a Kirby G4 and i'v replaced the carbon brushes myself using a step by step guide however since its been back together it worked for about five minutes it then started sparking from the inside!!(a lot!!) I'v obviously touched something i sh ... Kirby Ultimate G Bagged Upright Vacuum

Steam cleaner im using my cleaner have it all working but it just seems like its not cleaning right!!! i went over it for about 20 min and it has only cleaned a little of the stain am i doing something wrong or does it just take a very long time to clean!!


If it is spraying ok and the brushes are turning, then maybe the cleaner isn't strong enough for the typa of stain you are trying to clean. ... Hoover SteamVac Carpet/Upholstery Deep Cleaner Vacuum

Motor is noisy like there is something stuck in it. I am looking for the service manual so I can see how to take it apart/


Hi\015\012Generally modern upright vacs don't have screws that you can undo to get into the motor and most Electrolux/Eureka models have sealed units. I suggest looking at the sole plate where the roller brush is, check for anything clogging the main ... Eureka 5892AVZ Bagless Upright Cyclonic Vacuum

I have a Eureka Pet Pal and it seems to have lost suction on the main part of the vacuum. It looks like it sucked something up before it happened so I'm fairly sure that the tube is clogged but I don't know how to take the vacuum apart so that I can clear it out. Is there anyone out there than can help me figure it out?


... Eureka 2991AVZ Bagless Upright Cyclonic Vacuum

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara


... Vacuums

A black plastic ring fell off underneath at the bottom left... looks like it goes around something... ? bissell steamcleaner


Plastic or rubber? If it's a rubber ring it's the drive belt for the brush cylinder and should be replaced. You can buy one online or at a hardware store. ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I bought the Eureka 4703D model vacuum and my very first time powering it on, it was extremely loud - abnormally loud, and I don't know if it is loud like that because I possibly put it together wrong, or there is something wrong with it or it was previously damaged and I would like to know if this is something I can fix myself or do I have to take it back apart and return it to Walmart where I purchased it from. When it makes the loud noise, it does vacuum fine but the noise is just unbearable


... Eureka Power Plus 4703D Bagless Upright Vacuum

Dead motor? My 8 year old Miele S251i has worked fine, until I was recently vacuuming and moved the plug from one outlet to another. When I restarted the vacuum, it made rrrrr.....rrrrrr....rrrrr noises and smelled like something was burning. I turned it off, and it's shown no signs of life since. Sound like a motor problem? I've taken the cover off and looked at the cord and seen the motor, nothing looks obviously wrong, but I'm also not mechanical.


... Miele S251 Flamenco II Bagged Canister Vacuum

The brushes spin very, very slowly and stop altogether sometimes - like they just don't have any power behind them.I've cleaned the brushes and also turned it on without the brushes inside to see if the female plug that the brushes go into turns - it does, but not very fast. My husband said he thought he smelled something - like burning. Is there a way to take the underside cover off and clean something?


... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

After plugging in the steam mop, waiting for the 30 sec, pumping 12-15 times - no steam comes out. the tank is full and if i take off the bottom attachment the steam sprays everywhere. but the steam will not come out when mop head is on. thanks


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it may not be getting steam to the head...Euro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I bought a Hampton Bay Hawkins 44 " ceiling fan (117 391) and would like a remote that I can control the speeds with not just the on and off. I have a pull chain for the speeds but would like to use a remote instead. Is this possible? I have a Hampton Bay Redington IV and love the remote. I'm looking for something like that. Thanks Madeline Lepisto


... Vacuums

I purchased a Euro-Pro Steamer Mop 9 months ago and the Mop had just quit steaming. The green light is on and it makes a steaming sound but it is not getting hot and does not shoot out any steam like it should. Does it have an element or something that has gone bad in such a short time???


Hi,Yeah, element is bad...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My Domotec handy steamer bought from Lakeland is not producing any steam. Have only used it a few times. makes a big noise and gets hot but no steam. I don't want to hold trigger too long in case something blows. In past steam has been quick to come out as soon as red light goes off. Any ideas?


... Domotec Vacuums

My shark steamer has stopped working after a year of having it (I have already replaced one, I'm a idiot!). My problem; however, is that it will steam, but the steam stops traveling through the actual "mop" part. I plugged it in, wait seconds and start pumping, but the steam builds up until it's hard to pump. I had to press the button really hard for the bottom to come off and it shot off like a rocket! I tried to stick something through the tubing, but it did nothing. What am I doing wrong? I


\012\012\012Hi,Here\012is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it\012may not be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My euro steam mop is not getting steam to the head, it gets hot but no steam comes out. looks like an ongoing problem with these mops/ can you help?


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Problem ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Belt type Ok, thank you for the help! I did have the top off, but did not know the taking the motor loose trick, thank you for that! Now I have a couple of more questions, and thank you so much for all of the help! I got a belt from sears, & the sales guy sold me an off brand belt. It looks just like the belt that broke, although do you have to force the motor back down into place? I think it may be the wrong belt? I have looked on the Hoover website & they do not even have parts listed fo


The belt number is 91001028. The belt will be snug but not real tight, so the belt you got may not be the right one. Most repair shops for vacuums should have this belt in stock. ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Changing belt How do I do that? It looks like I would have to take the screwdriver to the bottom and enter the engine compartment. I'm not sure that I feel confident to take this machine all apart and be able to get it back together again.


Its not the engine compatment take the screws out the cover 4 the roller will come off then u can c where the belt goes ... Dyson DC18 all floors Bagless Upright Cyclonic Vacuum

This is embarassing, but I have just looked at the Dyson DC07 manual and at my Dyson for about 20 minutes, and I can't for the life of me find the wand release button on my actual Dyson.....the manual pictures don't look like the parts on my Dyson....I don't have a hose with a wand release button....the hose just goes straight up inside the handle....Can someone help me? Thanks :)


Hi the wand release button is located directly above the the Cylinder release button. The wand release button looks like the picture below. In order to releease the wand you must firstly make sure the Electrical cable is not wrapped up for storage. S ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Very hard to push all of a sudden... its like the direct drive assist is not working all of a sudden... I can see the cable below and it appears attached but looks like it may be hanging up or something


What kind of machine is this?\015\012\015\012Sounds like the self propel function of you hoover is broken and needs replacement ... Vacuums

Our housekeeper has twice pulled the cord out past the yellow marker and we've had it repaired both times at a cost of $75 ea. The housekeeper is now gone but I would like to try and fix the problem myself but cannot find disasembly instructions. Looking for some assistance as I really don't feel like spending another $75 if I can take care of it. Thoughts ?


Try this. Set vacuum on it's back end. Gently pull out cord and release. It may take a few tries, but should work\015\012Repair/service manuals are only available to authorized service tech at authorized Aerus Electrolux stores. These are i ... Electrolux Lux 5500 Canister Vacuum

MY NEEDLE GOES DOWN TO PICK UP BOBBIN THREAD AND SEEMS TO HIT SOMETHING SOLID. IF I TAKE THE NEEDLE OUT IT GOES ALL THE WAY DOWN. pLEASE HELP


Hi,i think the problem is with the needle bar,the alighnment has been distorted internally,i think you should re-align the needle bar in order to restore your machine back to a normal working condition.\015\012\015\012\015\012Thanks and t ... Vacuums

I have a Eureka 4870GZ. It turns on, but the brush roller doesn't move. The belt looks fine. I do have an extra belt and would try replacing the old belt, but I can't get the old one off the motor shaft or the new one on. I called Eureka customer service. The lady said there's supposed to be a small space between the motor shaft and the outside edge of the vacuum where I can slip the old belt off and the new one on. I don't see it. It looks like the motor shaft goes into a recessed place in the


Remove the top cover so that you can access to belt, You'll find 2 rows of 4 decorative holes on the top cover, In two of the holes you'll find the screws, Please use a flash light to see in that., Once the screws are removed, you'll be able to ... Eureka Vacuums

I have a Shark Steam Mop, model S3101, that caught on fire. Looks as though a wire inside rubbed until it became exposed and then caught fire. I have had this unit for about 1 1/2 to 2 years; liked the concept of steaming my floors rather than using detergents. I am not happy though about spending $100 on this unit and then it only lasted this long.


... Vacuums

Roomba Schedular I have a Roomba Scheduler and it has worked great until recently. Suddenly it quit working. When it is charging the power light goes from red to green as it should, showing it is ready to use. When we turn it on to use, it will only go on for a few seconds then it shuts off like it is out of power. It is like it isn't really charged. Is there something I can try to make it work?


Let it charge for a full 24, or even 48 hours, regardless of the green light. If it still dies you probably need a new battery.. or worse. ... Roomba Robotic Floor Bagless Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0603 seconds