Having problems with your Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum ?

Mop head snapped off/broke. The axle that holds the handle in and makes it swivel broke on both sides with minimal pressure. Poor engineering. It's a piece of shit.

\015 It's made out of cheap plastic.\015

Answers :

Repair Help & Product Troubleshooting for Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Mop head snapped off/broke. The axle that holds the handle in and makes it swivel broke on both sides with minimal pressure. Poor engineering. It's a piece of shit.


... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a Beam Rugmaster Plus power head Model BM1 393 Type AB and the connection were the metal pipe meets the plastic swivel broke close to the unit. It appears like a manufacture defect in that is broke in two small places and not the entire unit. Can this piece be replaced or glued??


This is most likely repairable. Lots of the Beam parts are available. I would recommend checking out any local vacuum shop or searching online for a central vacuum store that sells beam products. ... Beam Industries 750 Classic Bagless Central System Cyclonic Vacuum

I have a Bissell Model 8905 Carpet Cleaner. I was going to replace the belts because the pump belt broke, but when I turned the machine over, a small piece fell out. It looks like a tensioner arm because it has a small round part at each end on opposite sides of an arm that has an offset or "dogleg" in it. I am looking for an exploded parts diagram to determine what the part is and where it came from.


... Bissell 8910 ProHeat Clear View Upright Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Search for bissell pro heat pump. bissell.com will not have it ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

No spray My Bissell Pro Heat 7901 will not put out any spray. I Took the pump out so I could get at it and disconnected the hoses. I put the one on the input side and the other in a bottle of water. Put the belt on the pump and turned on the machine .Nothing at all coming out of the pump. Where can I get a new pump? Also the lever that goes to the little flapper at the top under the clear plastic piece on the front that connects to the knob that changes from tools to floor broke off. Where can I


Pump part number is 2107181, the diverter valve # 2136988. You can Bissell and they can tell you who may have parts near you, or you maybe able to order thru Bissell.com. Before you took it apart, were you getting water to spray out of the hose. I ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Kenmore Progessive Lead wire "A" brackets broke on swivel


You could try GOOP adhesive ... Kenmore 25614 / 25615 Progressive Bagged Canister Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

We have several SGC-60D 1.5 Gal coffee urns and the front piece broke off. ( the tall rectangular piece that hold the tube on the front on) We've tried a couple of things but the new front piece won't connect to the screw to hold the tube on. Any suggestions?


... Vacuums

Sears progression kenmore canister va. Model 11623612300 on the wand, the plastic piece broke off, there is one long wand with two piece to it well the plastic piece, not on the bottom, where it hooks into the beater bar thing, but the other plastic in the middle. Can this be replaces?


Hi.The part is probably available as replacement.Please click here ... Kenmore Vacuums

Its hard to explain, I have a 4704 p Boss LightWeight Upright. The piece that holds the bagless cup onto the vacuum broke. So now the cup falls off, is there a way to get another piece or would i have to by a new vacuum for this one little piece being broken


Should be able to order what you need. Find a local shop, along with your model number, they should be able to order it for you. ... Vacuums

The Belt on my Dirt Devil broke...so I purchased another belt and as soon as i put it on and started to vacuum it also broke, i noticed that the metal piece the belt goes on was extremely hot and was melting the belt. Whats wrong with it?


It may be that the beater brush is bound up . This will cause slipping, of the belt. Take out the brush and clean out the bushing . Hair gets wound up in side. once you have it cleand out. Put a few drops of cooking oil in side the bushing on both e ... Dirt Devil& Breeze Vision Canister Vacuum Vacuum

I have Excellence 740. Only started using it yesterday. Pieced I have the Elna Excellence 740 and only yesterday started using it. I pieced several blocks. Took a break. When I started to sew again there was a loud clanking sound. I stopped the machine. Since I had only very minimal training I am at a loss as to what to do. I checked the manual and did not get enough informatio. Is there a service center near Miami, Florida? I do not want to mess around with this lovely machine.


... Vacuums

I have the Miele S175i Powerhouse Plus and it vacuums fine, but the bottom piece of the vacuum is broken. The head of the vacuum swivels freely and doesn't lock into place. Also, the connecting belt is messed up. How can I fix the head so that it doesn't swivel freely?


... Miele S175i Bagged Upright Vacuum

I have a new Euro-Pro shark model S3101. Used it one time and while I was doing my tile floor in my kitchen I reached under a cabnet to clean and hit the floor kick kind of hard and broke the head off of the shark. I have only the T shaped end on the shark now with the cleaning head broken off and looks unrepairable. I did kind of hit the floor kick hard but the plastic broke like glass. Can I put a new head on the remaining piece or is it repairable? thanks Angie


Hi,Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head...Euro-Pro Shark Steam Mop Pro ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

My foot pedal to my Bernina 930 broke last night. The plastic around the screws broke off so everything fell out... I have the pieces, but not sure how to put it back together. Can this be repaired.


... Vacuums

I have a eureka surface max 300, i saw smoke come out of my vacuum i seen that the belt was broke every time i change belt i run it on it snaps every time ive put 3 new ones and each one break right when i start it it looks like the metal piece is burning it is there a piece missing?? what am i doing wrong?? ugh i just purchased it couple of months agoo not even older then 6 months .. what do i do?


... Eureka Capture Upright Vacuum Vacuum

Hi, I have a pre-lit christimas tree and the top section the plastic end that inserts into the previous section is broke. the company that provided the tree I guess is no longer in business. any idea how you would fix this? The top tilts because a piece of the plastic of is missing on the piece that inserts into the previous section..


Find a piece of metal pipe with an interior diameter the size of the stem. Cut it long enough to cover the plastic fitting completely and press it over the old one. Put the upper section in position and fill the missing part with shards of wood - ham ... Vacuums

I have a bissell proheat carpet cleaner purchased in 4-18-2005 for $169.99 from kohls I have used it 6 times and the last time the brushes would not move cause the belt was broken and the end of the pump pulley which is plastic broke off so I reorder the pump unit and 2 new belts and now I see you have sent me a exact pump but the end that broke off that the belt rides on is made of steel or aluminum much strong piece of equipment I want to know if there was a recall for the machine due to mecha


I've owned my Bissell for over 5 years now & LOVE it! Even after vacuuming It pulls up tons of dog hair I never realized was there! I am having a similar problem, but I caused it myself & think maybe you may have the same problem, cross you ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

I broke the handle part of the shark steamer #53101. I don't have the book to try to tell you the parts I need. Can you send me a picture or a copy of the steamer. It is purple. The above number may not be the correct one. It is broken in the center part. It has a little small circular piece that joins the two pieces which are broken. The beginning of the handle at the bottom of the steamer and the next session which has the steam release. The top of the handle is okay . It the middle and bottom


Hi,Ann there are very few parts for these...Here is a tip that I wrote about the Euro-Pro Shark Steam Mop and why it maynot be getting steam to the head... ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

I have a kirby G4 and the mini emtor is broke off. It looks like there is a piece that connects the mini emtor boot to the base of the vacuum. I was wondering what that part is or if it is just part of the mini emtor that broke off and stayed attached.


Hello, hrjI was trying to help you out here. Maybe this will help some? I was going backto some customers that asked questions in the recent past and even fartherback. It appeared that no one answeredsome of them, So, I thought I would tak ... Kirby G4 Bagged Upright Vacuum

Broken Elevator? One side of my brush will not stay up. Could this be a broken elevator? I think the elevator (black piece) has fallen into the machine. How do I get into the bottom to get the piece out and repair/replace it?


Asdasd ... Bissell 7901-1 ProHeat Scotchgard Upright Wet/Dry Vacuum

Broken Piece In the neck of the hose where it meets the head there's some kind of adjustable piece that goes inside the tip of the hose to hold the two together. It resembles a "C". Cleaning lady broke it and I'm trying to figure out where together another one. Anyone know what I'm talking about? Thanks!


... Electrolux Harmony Canister Vacuum - EL6985 Vacuum

Piece with spring attached to bottom of brew basket broke off.


... Jarden BVMC-PSTX91 Mr. Coffee Optimal Brew 10-Cup Thermal Coffeemaker

Red piece brush holder broke on bissell powersteamer


... Vacuums

Last time I used by Hoover it worked fine, took brushes out to clean them and now when I try to put them back in they won't snap into place and lock. Looks like all tabs on both sides of the brush piece are there and I spin the brushes for the center spindle to line up but it won't snap into place.


Just slightly turn the brush wheel, The tabs look square, but are just a little different in one direction ... Hoover F7425-900 SteamVac V2 Widepath Upright Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0246 seconds