Having problems with your Euro-Pro Ultra Big Shark Turbo Hand Vac Xsh166 ?

My ultra big shark, Model HV166, overheated and will not start again. Does this mean the motor is gone?


Answers :

Repair Help & Product Troubleshooting for Euro-Pro Ultra Big Shark Turbo Hand Vac Xsh166

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

My ultra big shark, Model HV166, overheated and will not start again. Does this mean the motor is gone?


... Euro-Pro Ultra Big Shark Turbo Hand Vac Xsh166

I have a Hoover, Steam spin scrub, Model F5897-900. Only used it a couple times and the motor gave out. First started being noisy then a bad smell. It did seem noisier that what I would expect from the start but I didn't realize it was a problem with the shaft of the motor. I took it apart and found the motor shaft wasn't true and causing sparks. The motor looks like it can not be taken apart and repaired. This seems like a default from the beginning but it is past warranty. Also noti


You will have to replace the motor and the hose asm. thehooverstore.com may be able to help, or you should be able to find a repair shop that can order them for you. ... Vacuums

I bought a Tacsew T8700 High Speed Stright Stitch and I should have paid more attention to the 'High Speed'! The motor that came with this industrial machine is a Tacsew Clutch Motor model: RM1878-1H. It is way too fast when starting out and usually breaks the thread. The local company I bought it from told me there was not a user manual for the machine or the motor :P. I've finally gottin the tensions adjudsted but still need to be able to start sewing at a slower speed. Any advice out the


If you are just starting off sewing and don't have good foot control change the motor to a d/c motor they are about $120 and you can turn the speed of the motor up or down ... Vacuums

Model # 5770 the brush motor runs and shuts down after a few seconds...Turn unit off and the brush again will run for a second or two...If I don't turn unit off brush will not start up..Could it be the printed board..the motor brushes..or the wiring that goes from the printed board to the main motor...Thank you


Seems like your unit goes into failsafe because it detects something wrong. Well you should check the brushes and replace them if they are worn out. Also check the wiring for shorts etc, becaue the unit maybe tripping due to an overload. The printed ... Bissell Vacuums

I have a eureka model 5190. The motor starts then


... Eureka Altima Upright Vacuum Model 2996AVS Vacuum

The motor is shot on my shark XSH035. can I get the motor replaced - as I prefer the attachable, flexible hose feature for cleaning cornors & creavices and the newer hand-held models do not provide this option.


The motor is available from manufacturer.The manufacturer website is currently not working, here is the website: ... Euro-Pro S3325 Handheld Steam Vacuum

Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc


Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum

I have usha Janome wonder stich model No. 392 , I need a new motor as my previous motor has gone unserviceable and is beyond repair. Please advice me how to get it as i am located in Mumbai


... Vacuums

BEAM model 178 central Vacuum. Motor will not start. Has power but just won't start. No click when switch is turned on. Is there any fuse to check? Could it be the relay? Any other thing to check? Thank you. Pierre


... Vacuums

Have a rexair model D series vacuum cleaner that worked fine until recently. Started making noise and then started smoking/overheating. I took apart the machine cover and am unsure how to get it tore down to see the motor or belt in there. Please help!


Below I have listed a link to the manual that has instructions on how to change your belt and a link for the replacement belt you need. ... Vacuums

Can't find a site to order a replacement belt for my Shark model V15Z which I bought for our motor home. It was used very little before the belt broke. I will be trashing this vacuum, and will NEVER buy another Shark product.


This web site has the belt for V15Z http://www.appliancefactoryparts.com/vacuumcleaners/brands/shark/v15z.html I found this one works great Pain to get belt on but not a problem since then. http://www.totalvac.com/ROR-1040.html (Dirt Devil type 1 Bel ... Euro-Pro Cordless Bagless Upright Sweeper - Blue/Gray

Vacuum cleaner Lux model motor fails to start


Can you provide more information? Is it the vacuum or power nozzle motor? \015\012There are a couple items that should be checked.\015\012Full bag will cause the vacuum to shut off.\015\012Hose blockage could be another problem. ... Electrolux Lux 7000 Bagged Canister Vacuum

Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio


Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum

Helping out someone that has a ECV 1590A model 117A Electrolux central Vacuum. There seems to be a problem with the brushes. I'm looking for a manual or what brushes to get or a new motor. It seems to run fine what it starts.


... Electrolux Vacuums

My dyson hoover keeps cutting out and smells of burning i cant see any obvious blockages does this mean the motor has gone


Hi, It definitely sounds like the motor is toasted.If you visit\012http://www.sparesaver.com/help-and-support/dyson-section/dyson-technical-advice-450/\012they have alot of info on repairing dyson cleaners AND they sell the\012parts, chea ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Brush rolls of my Euro-Pro Shark vacuum (model-UV 210CN) are stuck; the brush is unable to roll. Does that mean I have to the roll on one end or the whole brush unit? I live in Canada and if possible let me know where I can find a store. Thank you.


... Euro-Pro Shark Professional Upright Vacuum with Bonus StickVac Red Bagless Vacuum

RE: Goldstar dehumidifier: Model #DH404EY6, S/N 602TAQP05412 My unit is ~4 yr. old, has worked w/o problems until now. It will no longer auto. turn on. When I manually turn it on, the motor turns on, and then immediately shuts off, and "01" appears on the LED screen for humidity level setpoint. Is this an error code, and what does it mean? Can the unit be repaired? Thanks, Wolfgang


... Vacuums

I have a montgomery ward Signature floor polisher. The motor only buzzes, does not start. the model # is USS 682c G Can it be repaired?


... Montgomery Ward Vacuums

During re-assembly of my conair (model HC91RS) i noticed that my two blades do not line back up. The big blade sits evenly in it's space but the small blade is tilted slightly to one side. Is there any other means of aligning these two blades?


... Vacuums

Ihave a Hoover Windtunnel self-propel model U6445-920. The belt from the drive motor to the big wheel will not run in the center of the wheel. The belt runs about 1/3 off the wheel. I have tried several new belts and still the same problem. What do I need to do to repair this problem.


The large wheel may be worn off center. If the belt stays on and is not thrown, you can run the vac. if there is wobble in the wheel causing a genuine belt to slide off replace the wheel mechanism. ... Vacuums

Model 505 king No power, motor does not start, cord will not rewind - lead may have been damaged


... Nilfisk Family Vac Bagged Canister Vacuum

I have an easy flo vacuum model # 199C and it won't shut off. It started out as an intermitent problem but now will not shut off when the hose is unplugged, nor when the off/on switch on the main unit is shut off. the only way to get the motor to stop running is to unplug the unit. Any ideas?


Just had this same problem. I unplugged the low voltage signal wires and the vacuum stayed on. Thus eliminating the possibility of the signal wires shorting out somewhere. I'm not really sure which wire(s) were causing the problem. But when I disasse ... Easy Flo EF1500 Vacuum

I have a vax cylinder model V-094. Working fine then started to play up. Switch it on and the motor seems to struggle to power up. Kind of wurrs up and down. Was thinking it could be the brushes have worn. Tokk to bits and cleaned her up, took a look at motot and brushes, cleaned them too, back together and still them same problem. Help please, hoover is not old but has done some work really don't want to through away something that can be fixed.


Hi.\015\012\015\012after all you have done I would be pretty confident its the motor thats faulty they are expensive to buy so machine is going to be scrap,\015\012\015\012Sorry.\015\012\015\012 ... Vacuums

I have a Euro-Pro Shark Cordless Sweeper Model UV610. The motor still runs but the spinning brushes are no longer spinning. Can someone that is familiar with this appliance please assist me at repairing it and/or what parts I may need for repairing it? Thanks T.R.


IT SOUNDS LIKE YOU HAVE A BROKEN BELT, THAT CONNECTS THE MOTOR TO THE ROTOR BRUSH. ... Euro-Pro Shark Cordless Stick Vacuum SV775R Vacuum

We have an Eureka The Boss Central Vac Model ACV2001B. When you plug in the vac the motor starts momentarily and then stops. What could be the problem? Thank you.


Most likely there is a short in the low voltage wiring in the hose. ... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0782 seconds