Having problems with your Euro-Pro UV209 Upright Vacuum ?
Starting my vacuum
\015 I have a Shark Pursuit tank vacuum and cannot get it started--everything hooked up that I can see.What could be wrong?\015
Power cords are the most common culprit. After checking the fuse, plug in and switch on, then wiggle gently pull and gently push the cable about an inch before it enters the cleaner and the plug. These are the classic places for the flex to fatigue and break. If this is the case, then cutting off the last 2 inches at the plug and refitting or replacing the plug is simple. If the damage is as the flex enters the cleaner (and I'm afraid it usually is) you need to figure out how to take this bit apart. Sorry, I don't know the model, so I cant help you there.
Repair Help & Product Troubleshooting for Euro-Pro UV209 Upright Vacuum
Tips for a great answer:- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
Suggested Questions/Answers :
I have a Eureka Power Plus vacuum, model 4702, type A. To start off, it never really had great suction. Marginal at best. Then today I was vacuuming and smelled something burning and turned off the vacuum. At that point, smoke started pouring out from the bottom of the vacuum so I layed it on it's side and the smoke cleared but I never found the source. Is it safe to turn on again after I let it cool down or is my vacuum "shot?"
Won't start. My son was using the vacuum & Didn't change the bag. The vacuum was making the full bag smell, but the light was't on & it didn't stop. I stopped him, changed the bag, checked the filter, closed the compartments & turned on the vacuum. Nothing happened. I checked to be sure that it was plugged in, that wasn't the problem. I've let the vacuum "rest" for several days, It still won't start. Any suggestions?
There is a reset button at the back of the powerhead. The user manual can be downloaded from the electrolux website, although I didn't find it very useful. There was some info on how to change the powerhead drive belt. ... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum
I was using my easy flow central vacuum, and shut it off. When I went to start it up again 5 min later, it would not turn on. I emptied out the filter, and reset the switch. When the reset button was pushed, it started up the vacuum, but the vacuum was not turned on in the house. It can only be turned on from in the garage and not on the actual hose. What is going on?
... Easy Flo EF2300 Central System Vacuum
I was vacuuming and noticed that the bag needed changing. the red light with the ! inside the triangle also came on. When the bag was changed, the vacuum would not restart. The red light came on. Tried the reset button but nothing happened. Tried unplugging and re-plugging in and nothing happened. Replaced all the filters and still it wouldh't start. So I brought it downstairs and tried one more time to get it to start. it worked! Is there something wrong with the vacuum cleaner? Was it overheat
It was overheated that is why it worked downstairs after cooling off. ... Miele S548 Bagged Canister Vacuum
I have a dyson canniter stow away vacuum. i've had it for 2 years and it just started having a problem. when i turn it on the motor starts just fine but the vacuum head does not turn on. Yet when i push it forward it trys to start and turns on for a second and turn off - almost like the connector isn't connecting the hose to the head very well anymore.
Hi, After reading you're problem, the symptom's are just like you said. Its just a matter of checking the connections. The connection where it plugs into the head it self. When you push forward the forward motion and down pressure makes ... Dyson "Stowaway" Canister Vacuum Vacuum
Simplicity vacuum My vacuum just cut off and now it wont start. I pressed there restart button but nothing happens I have 2 fairly old Industrial hitachi dry vacuum in my workshop both 110v and both wont start. Both i was told were manufactured in Italy and both have a manual and auto switch. It has a black top, takes an orange paper filter inside and its bin is dark blue. Sorry i've forgotton the model number. I've inspected the wiring but it's fine, could it be the motor and how do i gain acc
Just take it in to your vacuum store. ... Hoover U5753-900 WindTunnel Bagless Upright Vacuum
The breaker on the vacuum trips after about 3 seconds on. The canister was extremely full and started to smell like burnt wood, we fully cleaned out the unit. Now when the vacuum is turned on, the motor sounds weak, and then turns off in a matter of seconds,and we have to reset the breaker on the vacuum to get it to start again for another few seconds.
This sounds indicative of a worn set of carbon brushes on a dieing motor for a central vac. the armature is ,likely damaged causing teh breaker to blow. Please post back with more details as to make and model. Do not atempt to run the vac ... Vacuums
Once again having vacuum problems, when I push the start red paddle it hesitates and won't fully starts. It makes the noice to start but then it shuts off. Makes noise to start but then promply
... Eureka 4700A Maxima Bagless Upright Vacuum
I heard that a class action lawsuit against Oreck Vacuum is being started because of all the problems customers are having with their vacuums. Does anyone know about this? My Oreck is only a couple of years old and keeps burning up belts. I took it in after only one week of usage when I started to notice white smoke coming out of it and the smell of burning rubber. I feel like I got the old run-around, when the service tech told me he couldn't find anything wrong (but replaced the burned up belt
You are correct about the fact that legal action has been taken. Go to this link to read more\015\012\015\012 ... Oreck XL2200 Bagged Upright Vacuum
G5 vacuum won't start (turn on) when I try to use the accessory hose. It starts (works fine) when using the regular floor brush for vacuuming.
... Kirby G5 Bagged Upright Vacuum
I have a nearly 9 year old Electrolux Excellio Z5228 vacuum cleaner. It has recently started cutting out during operation. I cleaned the micro filter (between bag & motor) via brush & hitting against wall & seems / looks quite clean. I washed the gore filter (output from motor to clean the exhaust air) as per instructions, then let to dry. It was very clogged but now very clean. The vacuum clearner still cuts out often. Even after a long rest (say overnight) it still won't start, then ano
... Electrolux Vacuums
Miele Blue moon vacuum motor surging on and off and power light flashing. After many surges of the motor (on->off->on-> off etc), the motor no longer attempting to start as ferquently ie. now off for many seconds and may turn on for 1 second.. sometimes stops turming on and just power light flashes. There is also no voltage at the plug for the hose for the power head. I noticed that the vacuum first started having probs when hair was caught in the power head and the ovetrheating light went on
... Miele Blue Moon Bagged Canister Vacuum
Vacuum smell I have a new bagless Hoover Empower Widepath. When I start to vacuum, after only about 2 minutes, it starts to smell really bad, like rubber I would say. Is it band slipping, and how do I check that out to make sure??
Your belt is slipping, it is probably stretched and slips trying to drive the brush roll. Take the bottom plate off, check the brush also, make sure the ends turn freely. The belt runs from the brush roll to the motor shaft. If you can't get to th ... Vacuums
My lux 7000 has a new bag but when i start to use it with the power unit or without the unit shut's it self off i can reset the lites or the motor if you will by clicking the on off switch 4or 5 times and i'm ready to go again untill you start to work and off it goes you can repeat the switch thing as long as u want, it just won't let u vacuum ,it turn's it self off .I blew it all out but found nothing in it. if u don't try to vacuum it will run as long as u want to listen to it. Can you
Have you replace the afterfilter? It may also cause this if rather dirty. It's located under the tool caddy/air diffuser on the back half of the machine.\015\012Try this: Disconnect hose, turn on vacuum. Does it continue running? If so, pl ... Electrolux Lux 7000 Bagged Canister Vacuum
Vacuum brush Everytime I try to vacuum the vacuum makes a very loud noise and starts to shake. I'm thinking it is the vacuum brush because it feels like that's where the shaking is coming from. Could it be the brush?
Your suspision may be correct especially if vac is well used/older however may i suggest you turn vac over and investigate by removing the brush cover plate? then you may see what problem is?this could be debri trapped in roller/brush hous ... Kenmore 23313 Whispertone Bagged Canister Vacuum
Infinity Vaccum by Shark, model number NV31COS, will not start. The vacuum was running just fine until it grabbed the edge of a curtain. Turned it off to release the suction. Turned it back on and was working fine. About a minute later the vacuum was making an odd noise. Every 2 seconds or so it would "heave" (lack of a better word) then go away, then come back and so on. Turned the vacuum off and checked for blockage, none that could be seen or felt, and now the vacuum won't turn. Any suggestio
Carpet brush won't turn when vac on ... Euro-Pro NV31 Infinity Vacuum
Hi folks, my beam vacuum makes a very loud roaring noise quite often. the problem started when i was vacuuming up a quantity of vermiculite from my chimney. i think i overloaded the vacuum i think and it made this loud roaring noise. the vacuum tends to make thos noise when i am hoovering after 5 minutes or so. any ideas?. thanks in advance Tom....
If the filter bag is bad and didn't trap all of the dust, then it got into your motor, so you may have a problem with your motor now. ... Vacuums
Engine troubles I have a 1975 4x4 GMC full size van. The motor is a 350 cid small block on propane. The thing hadn't been running in 5 years and when I tuned it up I changed vacuum advance pod on HEI distributor and hooked to a better vacuum and now the hotter it gets the faster it idols and when I try and turn the timing back, it starts hard. Wondering if vacuum is too strong or what is up?
I haven't fixed it yet but I think I might have a solution for it. From the factory this thing had a 4 barrel carb and they put an equivalent size atomizer in it for the propane and over the years someone omitted the EGR system in it and propane is a ... Vacuums
Fantom vacuum vacuum starts running fine at first,but after about 15 mins the suction stops but the vacuum continues to run
Sounds like a partly clogged filter ... Fantom Vacums FM741 Twister Bagless Upright Vacuum
Suction Problem I was vacuuming and stopped to empty the cannister. When I started vacuuming again - the suction wasn't working properly. The vacuum was just pushing stuff around the floor. I cleaned the hair out the brush on the bottom and it still isn't working. It was working fine before I emptied the tube :( I can't figure out what happened.Help!
Greetings from GoVacuum,\015\012\015\012I believe what may have happened is that your vacuum cleaner belt has either broken, or been stretched so far that ithe brushes are no longer spinning fast enough. \015\012\015\012Here' ... Vacuums
Have Dyson DC 14. When tilt to vacuum, the handle and coiled hose comes away from the unit. The problem started when the little purple ridged curved part on front of vacuum cleaner right below handle came loose and a spring fell out from somewhere--don't know where. I pushed on the purple ridge part and it snapped back on. Now, can't get it loose again, don't know where the spring goes, and handle still comes loose from vacuum.
I'm not positive whether or not this is the wand handle because there are several versions of the DC14. However the device the locks and unlocks the wand in place is pretty similar between all the versions.The first picture is the wand re ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum
My Eureka Altima Upright Vacuum Model 2996AVS Vacuum wont turn on. Any advice where to start? I would think it may be a fuse but do not know where it is on this vacuum.
Generally, on something with a cord and plug, the first thing I suspect is a bad spot in the cord where it connects to the plug. One way to check it is to turn the vacuum on, plug the plug into a good outlet that you have checked to make sure it wor ... Eureka Altima Upright Vacuum Model 2996AVS Vacuum
Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall
That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums
I have the eureka capture vacuum and it works great; however, it has recently started making an extremely high pitched sound when I use it. It is still vacuuming but the noise is so loud it hurts my head and I can only vacuum for a few minutes at a time before I have to turn it off. What is wrong with it???
Dust is getting past the dust cup filter, to the motor. Call Eureka customer service. 1-800-282-2886. ... Eureka 12 Amp Capture Vacuum Upright Vacuum
Vacuum has burning odor when started - Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum
If it smells like rubber its the belt. if it smells like electrical its the motor ... Dirt Devil Vision Turbo W/Bonus Upright Vacuum Vacuum