Having problems with your Fantom Vacums Cyclone XT Upright Vacuum ?

The brush status indicator

\015 My Fantom Cyclone XT is now 10 years old. The brush status light goes from green to nothing and/or red and back to green. This happened on and off 6 years ago but had quit until now. It is always clean as as a whistle, nothing clogged anywhere or in the brush. Any ideas where I should go from here? Thanks!\015

Answers :

Try the brush belt condition
Repair Help & Product Troubleshooting for Fantom Vacums Cyclone XT Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

The brush status indicator

Try the brush belt condition ... Fantom Vacums Cyclone XT Upright Vacuum

Spin brushes spin freely on steam vac when not attached to cleaner indicator screen not dirty speed selector is in high position brushes are clean spin brush indicator when brushes attached to machine does not rotate

If this is a Hoover Steam vac, the turbine which drives the brushes is bad. If not a Hoover, then what is it, they are different, need brand and model number. ... Vacuums

I have a VAX V12 vacuum cleaner which suddenly stopped. The smell indicated Carbon Brush Problems. I contacted a service agent who told me that it was not possible to change the Carbon Brushes brushes on this model and they would need to change the Motor Unit.. To me this sounds very unlikely. Two questions please. Is it possible to change the Carbon Brushes and how do I get the cabinet apart which looks very difficult. I am well qualified electrically to do this job. Regards James Beech

... Vacuums

My bissell 82h1 has developed a very loud clattering noise. I cleaned the brushes and checked everything I could easily access to no avail. When I turn it on with the brush removed, the sound level is normal. With the brush in place, I can easily turn it by hand with no indication of it hitting anything.

... Bissell 82H1 Cleanview Helix Bagless Upright Vacuum

Last night as I was vacuuming, I noticed that the belt stop indicator light was on. I pulled out the hair that had gotten tangled around the brush in hopes of solving the problem. It didn't change things. I then unscrewed the entire bottom piece to take out the brush roller. I removed hair from the end piece of the brush roller and reattached the belt; however, I cannot figure out where the microchip is supposed to go so that I can reassemble the base piece by screwing it back together. It seems

Not sure what you mean when you refer to a "microchip" but maybe it is a sensor that works with the belt.\015\012Anyway, if you Google the make and model number of your vacuum you can probably get an exploded view or owners manual that might indicate ... Vacuums

Roomba red status light is flashing and i cant power it on. battery is fully charged and when placed on the charger it does not indicates anything, just the red flashing status light

... iRobot 4150 Roomba Vacuum

Brush not rolling, no brush indicator light on.

... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

Riccar model rad.7 upright (radiance). roller brush won't turn and red roller brush indicator is on. roller will turn easily by hand and belt is in place. how do i fix this?

As you already know, the red brush indicator light indicates that the brush roll has stopped turning, usually because an object has become stuck in the brush roll. When that happens you should turn the machine off (unplug it also for safety), remove ... Riccar 8955 Upright Vacuum

I have a minuteman c37115-14 MPV14 vacuum. When I turn it on the brush will rotate for a second or two and then it stops. The light indicates "brush is blocked". Any idea what my problem is? TY Mark

Check your brush roll for string (from the carpet) or other debris in and or around the bearings on the ends of the brush roll. Or check your brush height. If you have the brush too low/close to the floor it drags the brush down, telling the circut b ... Vacuums

My vacuum isn't working. The red light indicator comes on seconds after I start it, yet there is no blockage and the brush area is free of debris. I checked all the filters and no sign of blockage there either. The brushes don't turn and there is no suction. How can I fix it?

Brush motor not working. ... Fantom Vacums Cyclone XT Upright Vacuum

Hoover Deluxe Elite Rewind vacuum has stopped working as it should. The airflow indicator snaps on almost immediately after I turn it on whether the hose is connected to the brush or not. There isn&

... Hoover Elite Rewind Bagless Upright VacuumVacuum

After turning on power , brush roller freezes and indicator light turns red

Try turning the roller by hand UNPLUG VACUUM FIRSTit should turn very easy, otherwise it is bindingall uprights have this problem eventuallyhair and fibers get in roller bushing and seizeluckily disassembling is relatively easy, same ... Euro-Pro NV22 Shark Navigator Bagless Upright Vacuum

"brush status" light is red, not reen

... Fantom Vacums Lighting Canister Vacuum

Air flow indicator stays activated after filter has been cleaned. Brush spins, but very little suction. Dirt doesn't spin in cup.

Your vacuum is clogged. Check all of the air pathways, hoses, etc. The most common places to check are anywhere there's a joint in the airways, and also directly behind the brushroll. \015\012\015\012-R ... Hoover U5507900 Elite Rewind Bagless Upright Vacuum

Hoover Elite Deluxe rewind... Air flow indicator stays activated, after filter has been cleaned. Brushes spin, but very little suction. Dirt is not spinning in cup

... Hoover Vacuums

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i

At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

On /off power switch works but when i engage carpet/floor switch nothing happens/ no light to indicate its working and roller brush not turning

... Miele S7210 Bagged Upright Vacuum

Brush spin indicator does not spin when turned on. model F5915-900

... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

The performance indicator light has come on on my Eureka capture plus. Last night a t-shirt got caught in the roller brush and now it won't spin.

... Eureka 12 Amp Capture Vacuum Upright Vacuum

I have a Bissell 7920 ProHeat and only used it 4 times and the brush on the bottom has stopped spinning and when attempting to spray solution the flow indicator doesn't spin and nothing comes out. I have looked at all of the belts and they seem fine. I have also removed and cleaned the heating unit. Still nothing. Any other ideas?

Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell 7920 ProHeat Pro-Tech Upright Wet/Dry Vacuum

Just purchased a reconditioned model. Makes a ton of noise and the bottom brush doesn't seem to turn like in my old Oreck. Does that indicate it needs a new belt?

Your Dyson does have a belt but its one that cant be replaced it is called a clutch assy. if your roller brush isnt spinning then it could be that you dont have the purple knob on the left hand side if your facing the vacuum to the carpet setting. if ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Dear VacuumRepair, Some months ago, a user reported having a brush on a Eureka4870 that stopped turning easily, even on the highest setting, and after replacing the belt. You indicated that you had an idea, but that it is a lengthy repair, but I'm willing! Can you please advise?

Hi RobertBesides the presence pf some sort of obstruction, the only thing to prevent the brush from spinning jammed bearingsThe bearings sit on each side of the brush. Dirt, dust, hair and carpet fibre can build in the narrow ... Vacuums

I have a hoover steam vac deluxe and the brushes rotate very slowly and have little power. i have cleaned the indicator screen.

Check to make sure that the foam filter inside the recovery tank lid has at least a 1/4 inch gap from the top. Other then that, the turbine is what turns the brushes, either the shaft on the top of he brush block broke off, or the turbine is stuck. ... Vacuums

When the vacuum is running i get a check brush indicator lite, but once I put the hande in upright postion the light goes out

... Windsor SR12 Sensor Bagged Upright Vacuum

Roomba Scheduler Hi, my roomba scheduler is wobbling back and forth then stopping after a few minutes. It beeps "uh oh" and the orange status light comes on. I've cleaned every part I can think of or read about. I've replaced all the brushes and filters. Any suggestions?

... iRobot 4296 Robotic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0519 seconds