Having problems with your Fantom Vacums Cyclone XT Upright Vacuum ?

Remove brush motor

\015 How do i get to the brush motor\015

Answers :

First pry out the lens over the headlights. under the foil are two screws holding the top cover on. just lift carefully and the back of the cover pops off. the motor is easily removed, just one screw holds it in place.
Repair Help & Product Troubleshooting for Fantom Vacums Cyclone XT Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Bissell proheat 2x 9200 series carpet cleaner. I need to remove the Brush Drive motor. However, this series has the gear end of the motor shaft poking out a hole on the left hand side. I removed the retaining washer and pin from the gear shaft. I need to get the gear off of the shaft in order to remove the motor. It's not budging. How do I remove the gear so I can pull the motor out of the unit? Thanks .


Chap, I wish someone had answered this. I'm having the exact same issue. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

My bissell model 18Z6 has developed a loud noise and vibration when the brush is running. I have removed the brush assy and cleaned all the hair, etc but still the noise. I ran the brush motor with the belt disconnected and all seemed ok, but of course there was no load on the motor. I suspect a problem with the brush assy bearings or axle or both but I hate to just throw parts at the problem. any suggestions would be greatly appreciated.


... Bissell Vacuums

Brushes in motor are arcing badly and motor only occasionally will start. How do i remove the motor brushes for replacement. (from the green plastic case)


This is kinda of tricky. need to know what kinda of vacuum it is first. However if you get it apart. To fix this problem the armeture brass needs to be cleaned & you should replace both carbon brushes. Should be cheap to fix if you are up to it. ... Vacuums

I snagged a loose throw rug with the Dyson last night. It jammed the brushes which stopped spinning, Once I removed all the entangled fibers the motor won't turn. The vacume still sucks, but the brushes don't spin I'm concerned I burnt up the motor for the brushes


Have you checked the belt? You can do so by removing the bottom plate from the power head. Once removed, check the belt. If broken or worn, it needs replaced.\015\012An instruction video for replacing the belt can be found on the below link. ... Dyson DC17 Animal Bagless Upright Cyclonic Vacuum

HOW DO YOU REMOVE THE TOOTHED DRIVE WHEEL FROM THE BRUSH MOTOR ON MY BISSELL 9200E CARPET CLEANER. ALSO IS THE ATTACHED UNIT THE MICRO SWITCH? WHY IS THE MOTOR COVER STILL ATTACHED TO THE FRAME WHEN ALL 4 OFF SCREWS ARE REMOVED JIM


It is a snap lock plastic cap on mounted to the frame. ... Bissell 9200 Upright Vacuum

Do i need to do anything special when replacing the brushes in a lamb ametek 117500 motor? It looks like I can just remove the old brushes and insert the new ones. Is it this simple? Will the motor work again? Thanks


Http://geeksquad.fixya.com/ThreadView.aspx?prdid=0&thid=758676\015\012Generic problem for all Vacuums\015\012Do I need to do\015\012Posted by edkraynak on Jul ... Vacuums

I have a Kirby Dual Sanitronic '50' Vacuum Cleaner I bought in 1966. The motor does not start when I attach the belt lifter of the rug nozzle. When I remove the rug nozzle and detach the belt from the motor fan shaft the motor starts when I depress the nozzle switch and the power switch . Seems like the brushes in the motor are worn out. I do not have a manual for this unit. Can you assist me as to what newer unit is this compatible to and the problem I'm having at present??


... Kirby Vacuums

Bad Motor I have purchased two of the Kenmore direct drive beltless systems with Progressive systems. The first died after a year, the vacuum motor start making a grinding noies. I pulled the side HEPA filter and could see a fine coating of graphite like dust. Took it to a vacuum repair shop. They said the brushes were going and thus the motor was shot. I liked the vacuum and bought a second, 1 year later the motor is making a slight noise that and removing the HEPA filter I find a slight metall


That dust is from the carbon brushes on the motor. You may need to check them, and also clean out the motor compartment. A slight noise could be a motor bearing starting to go. Does the smell like rubber or electrical. If rubber, then the belt h ... Vacuums

Noise My Dyson DC08 is making a loud, rough, vibration/noise that seems to be coming from the from the rotating brush housing. I replaced the old belt which was several years old and slipping. When I run the motor with the new belt removed the machine sounds normal. The bearings on the rotating brush seem to be running smoothly when turned by hand both when out of the brush holder and when installed in the machine. I can't find anything rubbing on the belt or rotating brush. I applied a bit o


Hi there, it's Jack at Dyson.\012I'm sorry to hear you're having difficulty with your Dyson vacuum. From your \012description, it sounds like the model number you've supplied may not be correct, \012as DC08 is a cylinder vacuum which doesn't use ... Dyson DC08 Cylinder Bagless Canister Cyclonic Vacuum

I have a problem with my model 6585-3 bissell upright powerforce bagless turbo with turbo brush vacuum The brush has quit spinning upon removal i noticed that one side of the brush was free to spin the other side that has the rectangular piece to help hold into place seems to be locked up and will not spin is it corroded or have i lost a piece that joins with it that allows it to spin freely belts are good and motor is turning brush will not budge


... Vacuums

My Electrolux Regency Series upright vacuum brush motor does not activate. Cleaned the brush and press reset to no avail. Opened handle switch assembly and checked each wire attached to all three switch settings. Tried disassembling brush assembly but could not pry open after removing all screws.


... Electrolux Vacuums

How do I replace the motor brushes in my DC11? I cannot dismantle beyond removing the pipe attachment. I've removed the 6 fixing screws that are visible, but the machine is still firmly "together" as if there are still screws that I've not located. Does it snap apart? Are there hidden screws? Paul


You can buy brushes but if the armature is overheating changing the brushes wont help ... Dyson Vacuums

My dyson has started to give off an acrid smell when I use it. I have checked all areas for blockages, cleaned the removable filter and removed all hair from the brush but this has not helped. I am worried the motor is getting hot in use. Whats the best thing to do next? Thanks


... Dyson DC14 All floors Bagless Upright Cyclonic Vacuum

I need to replace the brush motor on my Bissell 9400...I can't figure out how to remove the existing motor. Took the clip off but can't get the gear off the shaft and the hole in the side isn't large enough to push the gear through...what's the secret?


... Vacuums

I have to replace the motor brushes in my Oreck XL model 2000RH. How do I remove the old brushes?


If it's an AC induction motor there are no brushes. ... Vacuums

I CAN NOT GET THE OLD BRUSH OUT I HAVE REMOVED ALL SCREWS BUT MOTOR PREVENTS REMOVAL


This information (if available) is not generic, therefore I require a Make and a Model number. ... Vacuums

Faithful Sebo X1 upright, about 12 years old, stopped working today. I replaced old with new dust bag, checked all dust paths were clear, checked main brush was clear/clean, and drive spindle rotated OK with fingers. When power switched on, the two red indicators briefly flash on then off, but nothing more happens, motor does not start - even with power reaching machine. Tried removing all consumables, refitting and turning on a few times to reset, no joy. Removed base cover, both belts were i


At 12 years, this vacuum has had a good long life. I suspect the motor is shot, but it could be due to faulty wiring and connections. A bad switch, break in the power cord, and worn brushes in the motor are other causes.\015\012I recommend ta ... Sebo Automatic X1 Bagged Upright Vacuum

Remove brush motor


First pry out the lens over the headlights. under the foil are two screws holding the top cover on. just lift carefully and the back of the cover pops off. the motor is easily removed, just one screw holds it in place. ... Fantom Vacums Cyclone XT Upright Vacuum

I was in the midst of vacuuming with my Dyson Animal when it stopped working. It smelled as though part of the motor burned up (there was hair and string wrapped around the brush so I stopped to remove it). Any ideas on an easy, quick, and inexpensive fix? Thank you!


Hi there,For guidance on clearing any remaining threads or hair from around the brushbar and resetting the machine, please follow the steps shown in the video below. Please note, the brushbar will never rotate when your machine is upright, so ... Vacuums

My vac has lost suction. When I vacuum it picks up very little, but when I remove the wand hose it has good suction. We have cleaned both filters, checked for blockage in all hoses & cleaned the beater bar brush. All to no avail. Is it the motor? Or is there a blockage deep in the vac somewhere? We're debating repair versus buying a new one. Hope you can help. Thanks.


Hi there,Sorry to hear you're having a problem with your DC14. Since you say you've already washed the filters and checked for blockages, it's probably best if you get in touch with us so we can run through some simple troubleshooting ste ... Dyson DC14 Animal Bagless Upright Cyclonic Vacuum

Our unit is 7024A Electrolux Oxygen 3 - it seems to work great but suddenly, the head or 'power brush' or whatever it is called - has died. I checked by removing the hose and plugging it directly into the body, but it is still dead. Without that motorized head working, the vacuum is useless. Is it worth replacing? The unit is only about 1 year old and has seen light use only. Very frustrating, since it was the most expensive unit in the store:(


... Electrolux EL7020A Oxygen 3 Ultra Canister Vacuum Cleaner Bagged Vacuum

Can't get to motor to connect belt after removing brush cover


I followed the instructions that were supplied @ the FixYa site, to remove the hood. Removing the hood was the problem. Just follow the online users manual pages 22 thru 26. you must spread the hood by the rear wheels to remove.\015\012Thank You Ve ... Hoover Soft Light Supreme U4262-930 Bagged Upright Vacuum

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums

My Vax Swift Pet Premium has suddenly lost suction. There was a lot of human hair wraped around the brush which I removed but no theres no suction at all. The motor sounds fine.


... Vacuums

Dc35 pulsing Hi I have a DC35 it works fine until i put the main head on and then the motor starts pulsing and cuts out after about 10 secs. If i remove the main brush head it runs fine again ? Please HELP :)


Check for debris in the head and remove ... Dyson DC35 Handheld Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0560 seconds