Having problems with your Fantom Vacums Cyclone XT Upright Vacuum ?

Beater brush runs intermittently - Fantom Vacums Cyclone XT Upright Vacuum


Answers :

Try changing the the belt.If it is worn it could cause your problem
Repair Help & Product Troubleshooting for Fantom Vacums Cyclone XT Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

Beater brush runs intermittently - Fantom Vacums Cyclone XT Upright Vacuum


Try changing the the belt.If it is worn it could cause your problem ... Fantom Vacums Cyclone XT Upright Vacuum

Brushes won't turn but vacume runs - Dyson DC07 Bagless Upright Cyclonic Vacuum


I suggest you check the drive belt, located under a cover on the bottom of the unit. It may appear to be good (tight and not worn) but 9 times out of 10 that is the problem. ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Fantom FM741B vacuum cleaner user manual - Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum


... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

Phantom XT cyclone switch wiring - Fantom Vacums Cyclone XT Upright Vacuum


... Fantom Vacums Cyclone XT Upright Vacuum

How do i replace the belt on my vacuum - Fantom Vacums Cyclone XT Upright Vacuum


There are two black screws on the back of the hood top that need to be taken out and then the top hood will come off forward. Then you can see the belt and rollerbrush. Slide to rollerbrush out and put on a new belt to the motor pulley and then put ... Fantom Vacums Cyclone XT Upright Vacuum

Dyson vacum beater bar does not work - Dyson DC14 Bagless Upright Cyclonic Vacuum


DC14 have two drive ... Dyson DC14 Bagless Upright Cyclonic Vacuum

Not picking up, not getting any suction. - Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum


Try to clean the filter out. I have a similar vacuum and I clean mine out and wash the filter out. Leave the filter to dry overnight before you use it again.If this fails try figure out if there is something blocking it so it is not able ... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

Need new roller brush ***. and belts FM741B - Fantom Vacums FM741 Twister Bagless Upright Vacuum


... Fantom Vacums FM741 Twister Bagless Upright Vacuum

Wont **** up anything - Fantom Vacums Cyclone XT Upright Vacuum


That\015\012 type of vac is notorious for stopping up where the 90 degree turn is. \015\012You may need to access it from the vac head by removing the beater bar \015\012or take it apart where ever you can access the turns and hoses. ... Fantom Vacums Cyclone XT Upright Vacuum

Need to change the belt on model #FC285HL - Fantom Vacums Cyclone XT Upright Vacuum


Http://www.fixya.com/support/p12053-fantom_vacums_cyclone_xt_upright_vacuum\015\012\015\012there is a pro waiting to help you live ... Fantom Vacums Cyclone XT Upright Vacuum

What year was this model made - Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum


... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

Beater runs but suction does not - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


The water will not come out of tub when pressing trigger to clean the carpet. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Beater bar won't turn - Fantom Vacums XT450K Upright Vacuum


Could be 1 of 2 things. first try to spin the bar with your finger. "MAKE SURE VACUUM IS NOT PLUGED" "NO POWER TO UNIT" If it does not move, it might be the barrings if not it might just a simple belt replacement. good luck. ... Fantom Vacums XT450K Upright Vacuum

Roller brush does not turn when vacum is on - Dyson DC07 Bagless Upright Cyclonic Vacuum


The belt is broken or stretched. You can get replacement belts for the DC07 here:Belt for DC07 with clutch ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Beater brush will not work - Dyson DC07 Animal Bagless Upright Cyclonic Vacuum


... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Beater brush won't run - Dyson DC25 All Floors Bagless Upright Vacuum


There is a switching device that controls this, and has to be sent to Dyson in California for repair, unless you are close to a certifid repair center ... Dyson DC25 All Floors Bagless Upright Vacuum

Beater brush will not rotate - Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum


If you have not had this unit in for any previous service, and you are tilting it back to engage the brush with the swich on carpet mode, then I would likely suspect the switch assembly in the upper handle. The new switch and harness can be replaced ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

The motor running the beater bar on ny Electrolux canister vacuum cleaner runs intermittently. It runs about 2 minutes and then cuts off and automatically starts again after a 1 to 2 minute interval. I have tried taking it apart and removing the dust and grit in the beater bar attachment but with no change in operation. What would you suggest?


Check all the wiring connections to make sure they're tight. \015\0121/2. Wiring to power nozzle motor or reset switch is loose.\015\0121. Cord from power nozzle to upper wand. If the plastic portion of the wand is cracked near the co ... Electrolux UltraLux 2000 Bagged Canister Vacuum

Fantom vacuum not sucking - Fantom Vacums FM740 Twister 300SE Bagless Upright Vacuum


... Fantom Vacums FM740 Twister 300SE Bagless Upright Vacuum

My wife had some thing caught in the front of our dyson dc17. Now when the beater brush is running it makes a noise. It still vacuums alright. I cleaned out the area around the beater brush.


It could be the belt has striped some of the teeth and may need replacing or the teeth on brushbar here is video how to check ... Dyson DC33 Animal Bagless Upright Vacuum

Fantom upright vaacum- cyclone XT


There are two screws just to the rear of the accessory compartment. There are also two hidden screws under the cord retractor lever. I tried to get the retractor off by pulling upward on it, but it just wouldn't come. It is not screwed down but held ... Vacuums

My DC07 Animal Bagless Upright Cyclonic Vacuum has a small attachment for vacuuming carpeted stairs. This attachment is currently not spinning its internal brush necessary to pickup the dirt on the stairs. The rest of the vaccum is working fine. The suction cap on this attachment is pulled out, as it should be. I have checked the vacuum over thoroguhly and there are no bloackages anywhere.


Make sure to extend the wand straight up and completely out of the handle and watch that you don't kink the hose. ... Dyson DC07 Animal Bagless Upright Cyclonic Vacuum

Beater brush is good, vacuum running no suction


This sounds like your vacs dust passage from the rotary brush to bag is blocked ? you can diy this if you turn vac over to show the brush and covering cover you will see cover is held by some screw/bolts ? remove these and cover then the brus ... Electrolux Vacuums

Bissell Power Track Cyclonic Upright Bagless Vacuum.. ..The spin brush works laying down....when upright it won't spin! I cleaned any and all hair from the roller....belt is not broken....but do I need a new belt though? The vac is a few years old bever replaced the belt yet.


You need a new belt. ... Vacuums

DYSON VACUUM BRUSH WON'T TURN - Dyson DC15 Animal Bagless Upright Cyclonic Vacuum


The problem will most likely be either with the PCB under a panel on the side of the chassis, or the small wires from it that feed the front brush motor. \012\012If you are technically inclined, you can ask for more detail on the repair here: ... Dyson DC15 Animal Bagless Upright Cyclonic Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1112 seconds