Having problems with your Fantom Vacums Cyclone XT Upright Vacuum ?

I have a Fantom, Cyclone XT vaccum and while attempting to clear a blockage the wires inadvertantly came loose from the power on/off selector switch located on the top front of the unit and I need to reinstall the wiring in the proper order


Answers :

Repair Help & Product Troubleshooting for Fantom Vacums Cyclone XT Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I have a Fantom, Cyclone XT vaccum and while attempting to clear a blockage the wires inadvertantly came loose from the power on/off selector switch located on the top front of the unit and I need to reinstall the wiring in the proper order


... Fantom Vacums Cyclone XT Upright Vacuum

Need proper wiring connections inside unit, where they have pulled apart from squeeze connectors.(Wiring diagram needed) Can someone E-Mail this to me? Fritz (an ''old'' mechanic) Folks I have talked to, say there is no specific model number for these units. They are just described by name, and serial #. and I have relayed exactly what was labled on the unit. Please post this and quit asking me to enter a "valid" product.


Fritz , thanks please confirm... there are likely more than 2 leads from the motor?? I have not seen or worked on the Tristar CXL as it is very new.You will have a high low function but: Should the power head function at both spee ... Vacuums

I need a relay board for a Nutone CV 450 12.6 amp dual motor vacumn unit. Where can I locate one? Part #??? Unit will run by itself, then shut off. Unit wll not run at all. It has a mind of its own. Crossed a couple of wires on one of the relays and the unit runs smooth as silk. I assume its the relay, but can't locate part number.


Why not just replace the relay? Part number 1094117... ... Broan-NuTone CV450 Central Bagged Central System Vacuum

Bissell - Model 1697 - Powersteamer Pro - Carpet Cleaner I took the unit apart to replace some broken pieces and I can not seat the bottom to the top without properly engaging the soap/water mixer. What is the proper assembly procedure. What is the orientation of the water/soap mix valve when I seat the top to the bottom? The soap/water mix valve needs to engage the knob screw threads but this assembly is a blind operation. Do I turn to the soap/water mix knob to water only then seat the


Hi,\015\012http://dl.owneriq.net/7/7e477b7e-4440-49cf-a219-b68d301549e3.pdf\015\012This diagram will help you see the diagram plus the part assembly no and place it accordingly.I have also given link for Bissell - Model ... Vacuums

My wall ceiling fan's control unit UC 9051T failed. Light switch button does not work. If I replace it with some generic universal unit, do I need to replace transducer located in the fan housing also, or all of them are compatible? Thanks in advance. M


First, you didn't say you checked that the bulb worked. Is that burned out?\015\012\015\012If bulb is ok, you will have to make sure the switch is matched with the fan (ususally a set of 4, 6 or 8 micro-switches have to be set the same i ... Vacuums

Motor/Fan does not run. I have removed and taken the top of the canister plastic motor housing apart and tested for power. I have power through the cord to the switch and power from the switch to the two wire terminals. I have not removed the motor. Looks like I will need special tools to take out the motor. The Vac looks almost new. It has been setting for several years. What do you think?


Sorry to read about your problem, I hope this helps you out.Well you can order a new motor at shop vac, check out this link.you dont have to remove to check the motor, just connect power to the motor leads ... Shop Vac QPMH450 Canister WetDry Vacuum

I just received a Sharper Image SI724 Hybrid GP air purifier and it will not turn on. There is a green light that comes on at the bottom front of the unit, but the light on the top do not show any color and do nothing. I have tried to clean the fine wires to no avail. Is it just a bad unit or is there an in-home fix I could use?


If you just got it and it doesn't work ... you should return it for an adjustment. If you fool with it, you will probably void any warranty there may be on the device. ... Vacuums

I just purchased an Electrolux Epic 6500 SR, Model #C102G. I found that inside the cover over the bag. But where is the Serial number? I can't seem to locate that anywhere. Also, in case it breaks, I will need a light gray color on/off switch button located near the front of the canister.rnThanks.


The serial number is on the bottom of the machine. I believe near the front wheels, but can't remember for sure.\015\012Parts can be purchased at any authorized Aerus Electrolux store. You can locate the one nearest you using the below link. ... Electrolux Vacuums

Hello! I have a Rainbow vacuum Model# D4C that needs a switch. I am only able to get the new style 4 wire switch and it has the 6 wire. Can I make the 4 wire switch work in place of the 6 wire?


... Vacuums

I need to wire the switch to my coleman 2234 push button 12v water pump in my camper trailer. it is wired to the battery now with the "red" connected through a small fuse. i just cant figure out where to wire the on/off switch to.


Hi there. When connecting a switch, it is important to remember that a switch will only "break" the positive (+) circuit, while the neutral wire will go directly to the battery. So, basically split the red wire coming from your pump and connect the s ... Coleman Vacuums

Wiring the switch for a kenmore vacuum cleaner I need to know where teh different colored wires go. It had a short in it so I replaced the plug but think I wired it incorrectly. Its a Whispertone 300 model 116.28612790 The canister works but the beater bar doesn't.( it worked before a rewired the switch. Thanks


... Kenmore 23313 Whispertone Bagged Canister Vacuum

Can you send me a La Cimbali M22 Premium espresso machine power switch wiring diagram? I have a machine without a power switch. The switch is on order but I still have to connect the 10 loose wires. Thanks, Terry...


... Vacuums

NuTone CV750 Central Vacuum won't shut off. The on/off switch on side of unit has no effect. Did continuity test on switch, it tests ok. I've disconnected the low voltage wiring at the side of unit, that had no effect.


I will assume that you disconnected the switch from the circuit when you did the continuity test -- that is really important.\015\012If so, then i think that the relay inside the top of the unit is stuck on, or the low voltage wires (inside the ... Broan-NuTone CV750 Central Vacuum

Need a wiring diagram for a karcher puzi 100 yellow. Mainly need to know which way round the wires go on the switches?


... Vacuums

My electrolux ambassador power wand quit working. I replaced the switch that shuts it off when the roller stops, but it wasn't the problem. The on/off switch is fine, the motor is fine. We have traced the problem to the wires inside the canister by opening the inside cover to the bag container. We see the power cords going into the canister but we're not able to get to anything. We can't find any screws to undo that would open it up in order to follow the wires deep into the canister. We've bypa


... Electrolux Vacuums

The power wand electrical connection on the power unit itself seems to be corroded. I think I need a new two wire plug to plug into the wand. the model is a Eureka 6984 A. I am able to disassemble the power unit if necessary and replace the wire and plug if one is available


Try hesco inc they have a on line store with all the vacs parts diagrams and fast shipping. ... Eureka Vacuums

Trying to attatch the wires from the light kit to the fan but the blue and white wires from the fan have white caps on them covering the wire. Do these need to be removed in order to attach the wires with the wire nuts? If so, how are these white plastic caps removed?


They're called "wire nuts". Turn them counterclockwise to remove, lay the wires you need to join side by side with the ends of the bared sections even and screw the nut on. lp ... Vacuums

Motor wiring My Vax VS19TL motor died and I have managed to get hold of a new Vax 006 Turboforce motor which is the same size . My problem is that the original motor had two wires (black and white) which ran to the PCB switch. The new motor has three wires (black, white and yellow). I have ordered the PCB wiring loom for the 006 motor but I can't find any documentation that tells me where each wire goes. Can anyone help?


... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

The switch doesn't click on and off. When I opened it up I also noted the wires going into the switch were melted off at the switch. Can I order a new switch and the connectors that attach to the switch?


You can order the switch and connectors from http://www.vacpartswarehouse.com/Eureka-4870-Ultra-Smart-Vac-s/1928.htm\015\012Pl ... Eureka Smartvac 4870 Bagged Upright Vacuum

Picked the zig cp3g at car boot sale,just what i was looking for,but no instructions just wires been cut,tidy little unit.on the battery transfer switch, red, green and blue. and from lights green,aux brown,and water pump yellow.....firstly how do i wire to power up,and how does the single wires from unit not have return wires,thanks.


Hi,\015\012\015\012For your requirement wiring will be following: the green wire will be from the knob beside\015\012the tree switch to battery switch. Red wire will be from another side of battery\015\012switch to circuit o ... Vacuums

Wiring diagram I havea Dog and cat appart and are trying to understand the wiring. From the power side I have a black then another black for a individual terminal each and 2 x blue coming from a single terminal on the 3 pin plug side. This is passed thruogh the switch to a 4 x pin terninal strip that has a brown yello blue and blak from top to bottom. Can any body help me with a wiring diagramm so I can traced these wires?? The problem with the vacuum is that the motor is not running. I am tryin


Hello, First check the cord to make sure you have continunity throw both leads, check\015\012them at the cord reel, there are 2 wires hooked up to it, if not then\015\012the cord is bad. Check the swith also, the next cause would be the\015\0 ... Miele Cat & Dog 326i Bagged Canister Vacuum

Wiring diagram I havea Dog and cat appart and are trying to understand the wiring. From the power side I have a black then another black for a individual terminal each and 2 x blue coming from a single terminal on the 3 pin plug side. This is passed thruogh the switch to a 4 x pin terninal strip that has a brown yello blue and blak from top to bottom. Can any body help me with a wiring diagramm so I can traced these wires?? The problem with the vacuum is that the motor is not running. I am tryin


Check the cord to make sure you have continunity throw both leads, check them at the cord reel, there are 2 wires hooked up to it, if not then the cord is bad. Check the swith also, the next cause would be the speen control mounted on the motor, par ... Miele Cat & Dog 326i Bagged Canister Vacuum

The handle was getting hot and we opened the handle and the wires were melted around the switch. I need a part number for it. All I have seen are 2 wire and this is a 3 wire. Thank you.


Had exactly the same problem with my upright Eureka Model 5893\015\012bagless. Eventually, the handle would get hot, and finally it just\015\012quit. When handle was disassembled, the wires were melted and it was\015\012toast. Ordered a switch aft ... Eureka 5893AVZ Bagless Upright Cyclonic Vacuum

The brush wouldn't work when the selector switch was in carpet mode. Took the power head apart and removed the motor. Everything o.k. in the power head. Checked and found that the neutural wire had pulled out of the connector, the connector was never crimped at the factory. What a day! Took 2 hours and a large pizza to get it done. Neutral wire was in the hose just below the handle. Reconnected the wire and crimped it, put everything back together. It works!!!!


Great. ... Kenmore Vacuums

We have a Singer 626 sewing machine. It's an old mechanical machine with heavy metal parts. The stitch selector was stuck, I removed the top and helped the selector to move. when I had to move the selector again, it was stuck and I pushed too hard and broke a component. I can fix the machine if I had a repair manual. I need to buy a repair manual. How and where can I get one? Thankjs Charlie PS. Im pretty mechanicly inclined and I was able to clean the machine and get it to work after


... Vacuums
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.1139 seconds