Having problems with your Fantom Vacums Cyclone XT Upright Vacuum ?

I am trying to get to the belt on my fantom cyclone xt, although I am unable to see any screws to remove. I took the rubber bumper off thinking this would be of some help although nothing there either. Can you help???????


Answers :

Remove the lens covers, bulbs and the foil. under the foil are two screws. remove the screws and the cover lifts off. the motor for the belt is held in with one screw.
Repair Help & Product Troubleshooting for Fantom Vacums Cyclone XT Upright Vacuum

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Suggested Questions/Answers :

I am trying to get to the belt on my fantom cyclone xt, although I am unable to see any screws to remove. I took the rubber bumper off thinking this would be of some help although nothing there either. Can you help???????


Remove the lens covers, bulbs and the foil. under the foil are two screws. remove the screws and the cover lifts off. the motor for the belt is held in with one screw. ... Fantom Vacums Cyclone XT Upright Vacuum

Telescopic handle I don't think I have the exact same vacuum, although mine is a fantom upright bagless. I can't get the telescopic handle to stay in place. It pulls out whenever I try to pull back the vacuum. Any tips would be helpful! Thank you


Sometimes the locking mechanism for the wand wears out, make sure u have it all the way in and look where it locks and see if it looks worn ... Fantom Vacums FM760 Twister 500DX Bagless Upright Cyclonic Vacuum

I have only had my shark steam mop for about a month and only used it twice. I tried to use it yesterday and it would not work. The green light came on and it worked for maybe ten seconds, then it completely shut off. I tried switching outlets and draining the water but nothing worked. It still doesn't work today either. What do you think is wrong? Does this product have a warranty?


Yes has warranty call Shark/europro. ... Euro-Pro Shark Steam Mop - Gray/ Purple Vacuum

Again, I have a Bissel Model 3760-4. The same problem as everyone else. The beater bar will not turn. Took apart, nothing. Took to vacuum repair shop and they said it is not getting power to the motor to the beater bar. Seems like a fair number of folks are having this same issue. You would think Bissell would come up with a fix, if nothing else to save their reputation. Thanks Diane


... Bissell 37604 Lift-Off Pet Bagless Upright / Canister Vacuum CleanerVacuum

Hoover Model U8185-900 beater bar part keeps smoking and burning up We've replaced the part Hoover PCB Display Bridge U8172 three times and the vac beater bar works for about a minute then the part starts to smoke and burns out again. I've taken everything apart but cannot locate anything that would cause this part to burn up. I think if I did not disconnet immediately, he vac would catch my rug on fire. Help? I didn't send back the warranty card, so I can't get any help from Hoover. Any suggest


I'm not sure why this is happening. Perhaps if you would contact Hoover and explain the problem to them such that it appears that there is a safety issue with their product, they might be more cooperative. If that fails, I have had luck writing let ... Hoover U8185-900 Upright Vacuum

Either of my bissell porheat turbo 2x or my bissell pro heat don't have suction i would like to try and trouble shoot if i could due to the fact i am having difficulty finding a small machine repair center in my area could you possible help me or send a link which could help me find solution these machines are not more then a year and a half old if that thanks for your time and help warmest regards rebekah majors


Hi,Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.Bissell Proheat Upright Wet/ ... Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum

Altrev, I have an ODC325 Black&Decker spacemaker coffeemaker on my boat and it stopped working this weekend although the hot plate still gets hot. I suspect it is the thermal switch as you described (I hear a click when I switch the machine on but nothing happens and the heating element does not kick in). I would be very happy to receive one or two of these 14 spare switches you mention so I can repair the unit. If still available I would appreciate hearing from you how we can do the transact


We don't sell parts individually on the site here.... was it some other solution for another person you saw about the switch? I don't believe there really is a part called a thermal switch... there is a thermal fuse but if the hotplate gets hot I wo ... Vacuums

Hi all---I have a Dirt Devil 091020V. there was a problem with the wand where it was the only thing sucking even when it was stuck in the tube it would ****--but nothing from the vacuum end--the diverter was stuck closed I took it apart and found something stuck but in the meantime the torsion spring [I think} fell out and I don't know where it goes--so now only the vacuum works --not the overhead cleaner part.. is there a digram somewhere that can tell me where it goes--I think it might b


... Vacuums

My Bernina 807 set on min. speed takes off fast, doesn't go slow at all, although there is a difference in the slow speed setting and high speed setting if I switch from one to the other while stitching. The machine is well oiled and goes well apart from this. I would like min. speed to start smoothly and slowly. I have read it could be capacitor in foot, but DH says it does not look burnt out. Would it help my problem to remove it? thank you, Barbara


... Vacuums

Hi, I have been given a beautiful Husqvarna Prisma 980 and the power seems to have stopped getting to the machine.. The first time I plugged it in it worked, all the lights came up where they are supposed to, then the second time nothing =( Some help would be appreciated as I would like to fix it instead of throwing it in the bin Thanks Vicky


If you're really serious about getting this machine running, you need a service manual. Here is a .pdf download manual:\015\012 ... Vacuums

Hello, could you help please. I have a Bissel ProHeat 9400-M. The water remains in the bladder when the machine is on, in other words nothing happens and I cannot clean with it. Inside the tank the small flap is in the open position. I have always used your products although I did run the Bissell over an area that had been cleaned with another product. Could that have caused the problem by blocking it somewhere? I have cleaned everything and cannot see a blockage. Thank you for your help.


... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum

Belt type Ok, thank you for the help! I did have the top off, but did not know the taking the motor loose trick, thank you for that! Now I have a couple of more questions, and thank you so much for all of the help! I got a belt from sears, & the sales guy sold me an off brand belt. It looks just like the belt that broke, although do you have to force the motor back down into place? I think it may be the wrong belt? I have looked on the Hoover website & they do not even have parts listed fo


The belt number is 91001028. The belt will be snug but not real tight, so the belt you got may not be the right one. Most repair shops for vacuums should have this belt in stock. ... Hoover U8145-900 Savvy Bagless Upright Cyclonic Vacuum

Hi,My agitator brush won't run on my hoover S3590, I changed the belt, that didn't work. I don't see a possible cause in my book except replacing the belt. I think there could be a short, the brush will come on sometimes when pulling back and slightly lifting. Any ideas would be great and can I fix it myself? Thank you for any help, Bobbie


Hi Bobbie\015\012Take apart the electro floor head if you can and inspect inside - it may well be that there's clogged dust preventing the brush from turning and also check both sides of the actual beater bar as thread and tangled hair can often lead ... Hoover S3590 Bagged Canister Vacuum

The vaccum has been cleaned and checked but the brush is not rotating and no suction at the bottom, but through the hose. In reading the instructions to remove the brush cover it says to lift tab one and release 2-4. Where is the tab for tab 1 can not find anything for tab one to be able to lift, nothing there any ideas for help would be greatlly appreciated/


3 on the front and one on the back. where the belt runs ... Bissell 6594 PowerForce Bagless Upright Vacuum

The Petmate powerhead roller stopped rotating. I checked for anything binding it - nothing. There is power getting to it, just no rotation. As the guy said in the post above, it's like it is locked into the plastic housing, although it just worked last time I used the powerhead. Help!


... Kenmore 23913 Progressive PowerMate Bagged Canister Vacuum

My dyson turns on but when i push it to vacuum it makes this awful sound like something got sucked up and caught. i turn it off and turn it over and nothing is stuck. My husband even looked at it and he thinks it's the belt. The belt doesn't turn as loose. Please help.


If yours is one of the DC07 models that has a clutch (there's a knob you can turn, close to the front on the right side - right as you look from behind, that is). Sometimes this problem is cured by simply turning that knob from one extreme to the oth ... Dyson DC07 Bagless Upright Cyclonic Vacuum

Kirby G3 made loud noise when running. Sprayed silicon in fan thinking it might be a bearing. Found a coin and nail in fan and removed. Tha vacuum would not turn on. Replaced switch and brushes. Still nothing. Did the silicon spray do something?


No - the silicon is an insulating material and would have no effect on the electrics of the vacuum. Most likely you have a bad connection - dismantle the vacuum again and check the wiring and the motor with an ohmmeter. Be very attentive with the bru ... Kirby Generation 3 Bagged Upright Vacuum

Hello, I just bought a Bissell Powergroom (model 92L3-W) vacuum and a Bissell Proheat Pet (model 8910-3) deep cleaner and I love them both. My problem is, when we unpacked them we somehow lost the manuals; I think I had too many helpers that night – they may have gone out to the trash with the boxes. I need replacement manuals if you would be so kind as to help me out. Could you email me a manual for each of these two machines, or tell me exactly where to find them online? I’ve been looking, but


Follow the link below and enter the model numbers to access the User's Guides.\015\012http://www.bissell.com/customer-support/ ... Bissell 8910 ProHeat Clear View Upright Vacuum

I think I need to check yhe brushes on vax swift 1500 bagless how do I get to the motor taken some screws out nothing budged and now come to a standstill . Help please


If it's like my model, remove the top cover of the base unit (surrounds the hose connector), remove the drive belt underneath, remove the upright unit from the top of the motor housing. Hopefully, now the motor is just sitting there held by the swiv ... VAX Appliances Vax X5 Bagless Upright Cyclonic Vacuum

Help me with Search Tip: type in either product names or questions Search the entire site... or choose an option below Search the Web 1 Solution for "have miele solaris just had cord rewind repaired as motor would not go on. it's 4 yrs old" miele tech said "not common prob". & authorized repair said "yes-common prob,"


This is a common on some of the reviews I have read. The wires tend to break and sometimes wires get pulled from the motor itself. Problem - Vacuum doesn't go on at all.\015\012 Solution - You have some sort of electrical p ... Miele S514 Solaris Bagged Canister Vacuum

For some reason the adjustment thats in the front for lowering and highering doesn't seem to be working is there a manual that I could see in adobe that would show me how this is supposed to be I think I have it on right but when I look at the bottom to adjust it doesn't seem to do nothing [email protected]


My printer will not fax it says modem no exheistence?\015\012what does that mean and how can i get into fax settings ... Dirt Devil M086700 Vision Bagless Upright Vacuum

I would like to see how to change the belts on the bissell 8910 pro heat I have looked for hours now. I saw the book but it mentions and shows nothing on how to replace them. Help please.


Turn the vacuum over so that the bottom side is facing you, remove the 4 screws on each side using a Philips screw drive set the screws and the brush cover aside.- pull brush straight out and you will see the gray rubber band.-replace the ... Bissell 8910 ProHeat Clear View Upright Vacuum

The electricity in the apt attached to my house lost power in two of the walls. It happened when the cleaning ladies I think were using a vacuum, they don't speak english very well so I'm not sure. I have looked at the circuit breaker a # of times and nothing seems to have been tripped. I have also inspected the outlets and they seem to be fine. Can you help me?


Even know the breaker doesn't look tripped it might be. You have to flip it all the way off and then back on again. That is most likely what has happened. If that doesn't work check to make sure a GFI hasn't tripped. They are usually loc ... Vacuums

Suction button Although my Hoover Spin scrub is working perfecting dispensing the solution, when I go to suck up the solution from the carpet--I am having problems with the RED suction button that keeps popping up. I have to stop the cleaner and lift up the dirty water container to break the suction. Ive tried cleaning the netting that is encased around it, but still no luck. Any help would be appreciated! Thanks


This happens when the filter on the inside of the lid for the dirty water tank is pushed all of the way up. You need to leave a 1/4 in. gap from the top to the top of the filter ... Hoover SteamVac F5914-900 SpinScrub Upright Vacuum

I have a proheat 2x, and the pump will only spray water for a few seconds when unit is turned on, then nothing. The attachment is the same way. I think this is the pump failing, and the unit is only over a year old. How much would a pump cost? If this is the problem.


I just had my pump replaced for $66 and the repairman said this unit is notorious for this problem. He had 6 other units in his shop when we came in. Make sure you keep your clean water tank FULL, as he said the pump fails as soon as it runs dry. ... Bissell 9500 ProHeat 2X CleanShot Upright Deep Cleaner, Red Berends Vacuum
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.mictaservice.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0658 seconds